-
Date submitted2024-03-20
-
Date accepted2024-11-07
-
Date published2025-02-27
Analysis of the stress state of rocks transformation near a horizontal well during acid treatment based on numerical simulation
The article presents an overview of the assessment and modelling of the stress state of rocks in the near-wellbore zone of horizontal wells during acid stimulation of the formation for improving the efficiency of oil and gas field development. A numerical finite element model of near-wellbore zone of the reservoir drilled by a horizontal section was compiled using one of oil fields in the Perm Territory as an example. The distribution of physical and mechanical properties of the terrigenous reservoir near the well was determined considering transformation under the action of mud acid for different time periods of its injection. Multivariate numerical simulation was performed and the distribution of horizontal and vertical stresses in near-wellbore zone was determined with regard for different values of pressure drawdown and changes in stress-strain properties depending on the area of mud acid infiltration. It was found that a change in elastic modulus and Poisson's ratio under the influence of acid led to a decrease in stresses in near-wellbore zone. Analysis of the stress distribution field based on the Coulomb – Mohr criterion showed that the minimum safety factor of rock even after the effect of mud acid was 1.5; thus, under the considered conditions of horizontal well modelling, the reservoir rock remained stable, and no zones of rock destruction appeared.
-
Date submitted2023-07-04
-
Date accepted2024-05-02
-
Date published2025-02-25
Study of the pore structure in granite and gabbrodolerite crushed stone grains of various sizes
- Authors:
- Elena E. Kameneva
- Viktoriya S. Nikiforova
The results of a study on the pore structure of crushed stone grains of various sizes, obtained through staged disintegration of gabbrodolerite and microcline granite – rocks differing in texture, structure, and mineral composition – are presented. Research conducted using X-ray computed microtomography revealed that disintegration leads to changes in the pore structure of the rocks. The increase in overall porosity and pore concentration in the crushed stone grains is associated with the formation of newly developed pores of various sizes and sphericity. A clear relationship between the porosity of the crushed stone grains and their size is absent, which is due to the textural and structural characteristics as well as the mineral composition of the original rocks. The scale factor is evident only in the case of gabbrodolerite, which is characterized by a fine-grained structure, massive texture, and stable mineral composition. Fine gabbrodolerite grains exhibit lower pore concentration compared to larger grains, which aligns with the statistical theory of rock strength, according to which the probability of defects (pores and microcracks) decreases as the sample size diminishes – the smaller the grain size, the higher its strength. In contrast, for porphyritic granites with an uneven grain size, the trend is reversed – smaller grains are more porous. A study of the porosity of individual rock-forming minerals in granite showed that pores are unevenly distributed in the granite crushed stone grains. The highest concentration of pores is typical for microcline. The presence of brittle and porous microcline inclusions in the granite crushed stone grains leads to the formation of new pores and microcracks, whose number increases with the repeated application of load during staged disintegration.
-
Date submitted2023-10-29
-
Date accepted2024-04-08
-
Date published2025-02-25
Evaluation of the impact of the distance determination function on the results of optimization of the geographical placement of renewable energy sources-based generation using a metaheuristic algorithm
- Authors:
- Andrei M. Bramm
- Stanislav A. Eroshenko
Since the United Power System was created electrical supply of remote and hard-to-reach areas remains one of the topical issues for the power industry of Russia. Nowadays, usage of various renewable energy sources to supply electricity at remote areas has become feasible alternative to usage of diesel-based generation. It becomes more suitable with world decarbonization trends, the doctrine of energy security of Russia directives, and equipment cost decreasing for renewable energy sources-based power plants construction. Geological exploration is usually conducted at remote territories, where the centralized electrical supply can not be realized. Placement of large capacity renewable energy sources-based generation at the areas of geological expeditions looks perspective due to development of industrial clusters and residential consumers of electrical energy at those territories later on. Various metaheuristic methods are used to solve the task of optimal renewable energy sources-based generation geographical placement. The efficiency of metaheuristics depends on proper tuning of that methods hyperparameters, and high quality of big amount of meteorological and climatic data. The research of the effects of the calculation methods defining distance between agents of the algorithm on the optimization of renewable generation placement results is presented in this article. Two methods were studied: Euclidean distance and haversine distance. There were two cases considered to evaluate the effects of distance calculation method change. The first one was for a photovoltaic power plant with installed capacity of 45 MW placement at the Vagaiskii district of the Tyumen region. The second one was for a wind power plant with installed capacity of 25 MW at the Tungokochenskii district of the Trans-Baikal territory. The obtained results show low effects of distance calculation method change at average but the importance of its proper choose in case of wind power optimal placement, especially for local optima’s identification.
-
Date submitted2023-11-02
-
Date accepted2024-09-24
-
Date published2025-02-12
Mercury contamination of sediments at Indonesia Ciujung watershed: contribution of artisanal small-scale gold mining
Artisanal small-scale gold mining is the largest artificial source of mercury pollution and has been a very common problem recently. This study examined the contribution of Hg release due to artisanal small-scale gold mining in contaminating the sediment of the watershed in Indonesia. Different from other methods, we measured Hg pollution using the stable isotopes of carbon and nitrogen. This report is the first time analytical reports in Indonesia since most papers focus primarily on only detecting heavy metals in river water and sediments, neglecting deep research on Hg pollution and resources. The findings of this study indicate that artisanal and small-scale gold mining activities, located in the upstream areas of the tributaries that act as point sources, are the primary source of mercury in the sediment of the Ciujung watershed. The isotopes δ13C and δ15N successfully trace the Hg-contaminated sediment in the Ciujung watershed derived from the Cisimeut and Ciberang Rivers based on soil organic matter. The biological effect showed the Hg concentration in most of the sampling sites exceeded the Effects-range medium and Probable effect limit values. The Risk quotient values of Hg indicated the Hg pollution had a possibility effect on the benthic organism. Several limitations have also been added in this study and needs for further investigation.
-
Date submitted2024-03-11
-
Date accepted2024-09-24
-
Date published2024-12-06
Comparative analysis of nitrogen and carbon isotopic fractionation during diamond formation based on β-factor determination
- Authors:
- Dmitrii P. Krylov
First quantitative estimates are presented for nitrogen isotopic fractionation during diamond crystallization with respect to nitrogen-bearing fluid components using quantum-mechanical (DFT) calculations on the defect (with the substitutional nitrogen) diamond lattice. Provided equilibrium isotopic fractionation, 15N/14N ratio decreases within the sequence of compounds NH4+ > N2 > (diamond, NH3) > CH3N > CN− > NH2. At temperatures of 1,100 to 1,200 °C fractionation among diamond and fluid N-compounds are estimated at –2.23, –0.77, 0.01, 0.44, 1.31 and 2.85 ‰ and substantially (over 1 ‰) exceed the already available estimates based on the modeling diamond C-N bonds by analogy with HCN or CN – molecules. Depending on the dominant nitrogen and carbon substance in the mineral-forming fluid, diamond formation can be accompanied by different isotope compositional trends, as expressed either by zoned patterns within individual diamond grains or by isotopic δ15N vs δ13C covariations during successive crystallization. Provided the dominance of NH3 component (the reduced conditions, high pressures and the cold geotherm) nitrogen isotope fractionation between diamond and fluid does not exceed 0.1-0.2 ‰ and the isotope shifts at temperature ca. 1100 °C Δ15N << Δ13C. In nitrogen depleted reduced mantle fluids possible existence of compounds with low heavy isotope affinity at temperature of diamond formation (especially NH2) implies high isotope fractionation between diamond and the fluid and hence, evolved Δ15N/Δ13C ratios. Oxidized fluids dominated by CO2 or CO3 coupled with N2 component are characterized by close to zero Δ15N/Δ13C ratios as inferred by prevailing carbon isotope fractionation with respect to nitrogen isotopes, the latter change considerably with nitrogen distribution coefficient among diamond and the growth media.
-
Date submitted2024-09-09
-
Date accepted2024-11-05
-
Date published2024-11-12
Acoustic emission criteria for analyzing the process of rock destruction and evaluating the formation of fractured reservoirs at great depths
In order to study the mechanism of destruction of rocks of various genesis and the formation of fractured reservoirs at great depths, laboratory studies of rock samples in the loading conditions of comprehensive pressure with registration of acoustic emission (AE) and parameters of the process of changing the strength and deformation properties of samples were carried out. The spatial distributions of the hypocenters of AE events for each sample were investigated. By the nature of the distributions, the fracture geometry is described, then visually compared with the position of the formed macrofractures in the samples as a result of the tests. The time trends of the amplitude distribution b, set by the Guttenberg – Richter law, were calculated, which were compared with the loading curves and trends of the calculated AE activity. Based on the analysis of the AE process for three types of rocks – igneous (urtites), metamorphic (apatite-nepheline ores), and sedimentary (limestones) – parameterization of acoustic emission was carried out to determine the features of the deformation process and related dilatancy. As a result, three types of destruction of samples were identified, their geometry and changes in strength and seismic criteria were established.
-
Date submitted2023-07-07
-
Date accepted2023-12-27
-
Date published2024-08-26
Landslide hazard assessment in Tinh Tuc town, Cao Bang province, Vietnam using Frequency ratio method and the combined Fractal-frequency ratio method
Landslides are one of the most frequent natural disasters that cause significant damage to property in Vietnam, which is characterized by mountainous terrain covering three-quarters of the territory. In 17 northern mountainous provinces of the country, over 500 communes are at a high to very high landslide hazard. The main goal of this study was to establish landslide hazard maps and conduct a comparative evaluation of the efficiency of the methods employed in Tinh Tuc town, Cao Bang province. The landslide hazard assessment was carried out in this study using the combined Fractal-frequency ratio (FFR) and the Frequency ratio (FR) methods. The FR method is based on the actualist principle, which assumes that future landslides may be caused by the same factors that contributed to slope failure in the past and present. The FFR method is based on the determination of the fractal dimension, which serves as a measure of the landslide filling density in the study area. Eight landslide-related factors were considered and presented in cartographic format: elevation, distance to roads, slope, geology, distance to faults, land use, slope aspect, and distance to drainage. Determining the area under the receiver operating characteristic curve (ROC-AUC) and verification index (LRclass) was performed to assess the performance of prediction models and the accuracy of the obtained maps. As a result, five zones were identified for the study area, characterized by very low, low, moderate, high, and very high landslide hazards. The analysis of the reliability of the obtained landslide hazard maps using the AUC and LRclass indices revealed that the FFR model has a higher degree of reliability (AUC = 86 %, LRclass = 86 %) compared to the FR model (AUC = 72 %, LRclass = 73 %); therefore, its use is more effective.
-
Date submitted2021-01-21
-
Date accepted2023-09-20
-
Date published2023-12-25
Adaptation of transient well test results
Transient well tests are a tool for monitoring oil recovery processes. Research technologies implemented in pumping wells provide for a preliminary conversion of measured parameters to bottomhole pressure, which leads to errors in determining the filtration parameters. An adaptive interpretation of the results of well tests performed in pumping wells is proposed. Based on the original method of mathematical processing of a large volume of field data for the geological and geophysical conditions of developed pays in oil field, multidimensional models of well flow rates were constructed including the filtration parameters determined during the interpretation of tests. It is proposed to consider the maximum convergence of the flow rate calculated using a multidimensional model and the value obtained during well testing as a sign of reliability of the filtration parameter. It is proposed to use the analysis of the developed multidimensional models to assess the filtration conditions and determine the individual characteristics of oil flow to wells within the pays. For the Bashkirian-Serpukhovian and the Tournaisian-Famennian carbonate deposits, the influence of bottomhole pressure on the well flow rates has been established, which confirms the well-known assumption about possible deformations of carbonate reservoirs in the bottomhole areas and is a sign of physicality of the developed multidimensional models. The advantage of the proposed approach is a possibility of using it to adapt the results of any research technology and interpretation method.
-
Date submitted2022-10-13
-
Date accepted2023-10-11
-
Date published2023-10-27
An innovative approach to injury prevention in mining companies through human factor management
This study argues that human error has an effect on occupational injury risks in mining companies. It shows through an analysis of existing approaches to occupational risk assessment that it is necessary to develop a quantitative assessment method factoring in individual psychophysiological attributes in order to analyze injury risks posed to miners. The article presents the results of a comprehensive analysis of how workers’ psychophysiological attributes influence their susceptibility to occupational injuries in underground mining conditions. By utilizing statistical data processing methods, such as discriminant and regression analysis, the study develops models to forecast personal injury risks among miners. These quantitative models underlie the proposed method for assessing miners’ susceptibility to injuries. The study outlines an algorithm for the practical application of this method and shows how the method was validated using a training sample. It provides recommendations for managing the human factor, incorporating the results of the proposed method, and emphasizes the importance of implementing a series of protective measures to mitigate the risk of occupational injuries in underground mining operations.
-
Date submitted2022-09-30
-
Date accepted2023-04-03
-
Date published2024-02-29
Optimization of the location of a multilateral well in a thin oil rim, complicated by the presence of an extensive gas cap
- Authors:
- Кirill О. Тomskii
- Mariya S. Ivanova
The specific share of the reserves of hard-to-recover hydrocarbon raw materials is steadily growing. The search for technologies to increase the hydrocarbon recovery factor is one of the most urgent tasks facing the oil and gas industry. One of the methods to expand the coverage of oil reserves and increase oil recovery is to use the technology of drilling multilateral wells with a fishbone trajectory. In the Russian Federation, the most branched well was drilled in the Republic of Sakha (Yakutia) at the Srednebotuobinskoye oil and gas condensate field. The main object of development is the Botuobinsky horizon (Bt reservoir). About 75 % of the geological reserves of the reservoir are concentrated in a thin oil rim with an average oil-saturated layer thickness of 10 m with an extensive gas cap. This circumstance is one of the main complicating factors in the development of the Srednebotuobinskoye oil and gas condensate field. For such complex wells, one of the most important design stages is to determine the optimal location of the fishbone well in an oil-saturated reservoir. The article shows the results of sector modeling in the conditions of the Srednebotuobinskoye field to determine the optimal location of multilateral wells using Tempest simulator.
-
Date submitted2022-04-03
-
Date accepted2023-03-02
-
Date published2023-12-25
Specifics of geotechnical risk control in the design of underground structures
The underground space development is associated with the emergence of complex and dangerous situations, often leading to accidents. The condition for their development is the potential geotechnical risks. High-quality execution and analysis of design work at all the stages of design, starting from the early stages, is one of the effective ways to control risks. Clarification of the characteristics and features of the rock mass adjacent to the projected underground structure makes it possible to identify the potential cause of the occurrence of an adverse event with a certain probability during the construction and operation of an underground structure. The purpose of a qualitative risk analysis is to identify risk factors in underground construction. The value of the total geotechnical risk, expressed by the sum of each of the possible risks, should be numerically estimated at the design stage of a specific underground facility. At the same time, it is extremely important to develop a methodology for managing geotechnical risks, which would make it possible to assess their probability of development at an early stage of project preparation and propose measures to reduce or prevent them. This technique is given in the article. The results of the study conducted in accordance with the presented methodology showed that geotechnical risk control proved an effective method in preventing accidents during underground construction.
-
Date submitted2022-08-05
-
Date accepted2022-11-17
-
Date published2023-02-27
Feasibility study of using cogeneration plants at Kuzbass coal mines
The paper considers the problem of reducing greenhouse gas emissions in the process of coal mining during the coal mine methane utilization in power supply systems. An algorithm to form recommendations for the implementation of CMM generation is presented. A simulation model for one of the Kuzbass coal mines was developed in the PowerFactory software application. The simulation model considers the uneven nature of the power consumption of mining equipment. As a result of modeling, daily power consumption profiles and voltage levels in the coal mine power supply system were determined before and after the implementation of the proposed measures. Based on the results, the technical and economic effects was estimated, which consisted in reducing the direct and indirect carbon footprint, electricity and capacity fees. It has been established that the cost of carbon dioxide emission quotas significantly affects the investment attractiveness of cogeneration projects. Based on the results, recommendations are given to stimulate the development of small generation in coal mines.
-
Date submitted2022-04-15
-
Date accepted2022-11-17
-
Date published2023-04-25
Uranium in man-made carbonates on the territory of Ufa
The paper presents the results of analyzing uranium content in man-made carbonates (scale crusts) on the territory of Ufa based on examination of 42 samples. The median uranium content in the investigated samples stands at 1.44 mg/kg, which is significantly lower than the background values (scales from the Lake Baikal water, a clarke of sedimentary carbonate rocks) and data on other settlements of the Republic of Bashkortostan. Low values of uranium content are probably associated with the effects of the three leading factors, i.e. specific subsurface geology of the territory (gypsum, limestone); types of water supply; water treatment processes for the centralized type of water supply. Spatial distribution of uranium in man-made carbonates is characterized with uniformity, which is disturbed in two cases, i.e. a change of the water supply type (from centralized to individual); and material of the vessels used for boiling the water. No significant differences were detected when comparing samples of man-made carbonates associated with different sources of water supply (the bucket and infiltration types of water intake) and the types of household filters.
-
Date submitted2022-03-17
-
Date accepted2022-10-04
-
Date published2022-11-10
Improving the reliability of 3D modelling of a landslide slope based on engineering geophysics data
Landslides are among the most dangerous geological processes, posing a threat to all engineering structures. In order to assess the stability of slopes, complex engineering surveys are used, the results of which are necessary to perform computations of the stability of soil masses and assess the risks of landslide development. The results of integ-rated geological and geophysical studies of a typical landslide slope in the North-Western Caucasus spurs, composed of clayey soils, are presented. The purpose of the work is to increase the reliability of assessing the stability of a landslide mass by constructing a 3D model of the slope, including its main structural elements, identified using modern methods of engineering geophysics. Accounting for geophysical data in the formation of the computed 3D model of the slope made it possible to identify important structural elements of the landslide, which significantly affected the correct computation of its stability.
-
Date submitted2021-07-05
-
Date accepted2022-07-21
-
Date published2022-11-10
Fragmentation analysis using digital image processing and empirical model (KuzRam): a comparative study
The rock fragmentation reflects the degree of control of blasting. Despite the accuracy of screening analysis to determine the size distribution of blasted rocks, this technique remains complex and long because of the large volume of blasted rocks. The digital image processing method can overcome these constraints of accuracy and speed. Our method uses the empirical model of KuzRam and numerical method (Digital image processing) through two image processing software’s (WipFrag and Split-Desktop) to analyze the particle size distribution of rocks fragmented by explosives in Jebel Medjounes limestone quarry. The digital image processing is based on the photography of the pile of blasted rock analyzed using image processing techniques. The objective of this work is to evaluate and compare the results obtained for each blast from the two methods and to discuss the similarities and differences among them. Three different blasts with the same design were analyzed through the two methods. The result of the KuzRam model gave idealistic results due to the heterogeneity of the structure of the rocks; although, this model can be used for an initial evaluation of blast design. For better efficiency of the explosion, we proposed a new fragmentation indicator factor in order to compare the fragment produced to the estimated ideal size obtained from the KuzRam model by incorporating the blast design parameters and the rock factor. Both image processing gives close results with more accuracy for the Split-Desktop software. Our method can improve the efficiency and reduce crushing costs of the studied career.
-
Date submitted2022-06-02
-
Date accepted2022-07-21
-
Date published2022-10-05
Substantiation of the optimal performance parameters for a quarry during the stage-wise development of steeply dipping ore deposits
- Authors:
- Sergey I. Fomin
- Maxim P. Ovsyannikov
The use of stage-wise schemes in the development of deep quarries is one of the ways to increase the economic efficiency of mining a deposit and determining the optimal stage parameters remains an urgent task. Such parameters are stage depth, bench height, block length, etc. However, there is a wide range of values for these parameters. Therefore, to select the optimal values and evaluate the effectiveness of design solutions, it is advisable to use the net present value, which is an international notion. As a result of the analysis of data on deposits, a large number of variable indicators can be identified that presumably affect the efficiency of mining. The article proposes to divide all parameters of the quarry mining into two types: mine engineering and economic. The importance of each of them is determined by the measure of influence on the net present value. Thus, to assess the measure of influence of mining indicators, the average values of each of them are taken, and as a result of the alternating change of one parameter under study, the measure of its influence on the discounted income received is estimated. The results of the analysis of relevant factors, their evaluation and comparative analysis are important indicators that significantly affect the design decisions made and the effectiveness of the investment project.
-
Date submitted2021-10-31
-
Date accepted2022-04-26
-
Date published2022-07-13
Identification of structural control factors of primary gold ore occurrences by method of unmanned aeromagnetic survey by the example of the Neryungrisky district of Yakutia
The long-term development of the geophysical industry, in which the methods of magnetometry are in maximum demand, as the simplest in instrumental and methodological execution, has determined the development of remote measurement methods implemented both from space and airborne carriers. The necessity to use the latter as an obligatory component of field surveys, providing coverage of significant areas, determines the need for using the unmanned low-tonnage carriers. Their use is implemented to search for predictive elements of structural (spatial, genetic) control of endogenous gold ore occurrences that allow predictive constructions, i.e., solving the problem of increasing gold reserves, which is being performed within the framework of federal programs. The purpose of the survey is to develop a system of instrumental and subsequent interpretation approaches in the organization of unmanned magnetometer survey, implemented for structural and geological mapping by the example of the Neryungrinsky district of Yakutia. Within the framework of the digital model formation of the relief and the anomalous magnetic field, a survey method using an unmanned aircraft, its technical characteristics are considered; the analysis and the author's modification of the office analysis of magnetometry data are performed. Based on the obtained materials, a physical and geological model of the investigated area was created, which is presented in the form of a geological and structural cut, accompanied by the physical characteristics of the structural and material complexes. The refinement of the physical and geological model was implemented by a joint morphostructural analysis of the remote base and the anomalous magnetic field using the results of quantative interpretation of the anomalous magnetic field. The result of the study is presented by an updated geological basis with the allocation of promising ore sites for their detailing as part of the planned large-scale geological and geophysical surveys. The scientific novelty of the work consists in the synthesis of the tried and tested methods of unmanned aeromagnetometric measurements and geostructural reconstructions, which allow the processing of both potential and non-potential geofields.
-
Date submitted2021-07-19
-
Date accepted2022-05-31
-
Date published2022-07-13
Study of a set of factors influencing the error of surveying mine facilities using a geodesic quadcopter
The factors influencing the qualitative and quantitative components of the result of surveying in open-pit mining using a quadcopter were identified and systematized, and the mathematical dependence of the influence of factors on the final error of surveying was determined. After a large number of field observations – numerous flights of a geodesic quadcopter over mining facilities – the subsequent mathematical justification of the results of the aerial photogrammetric surveying was made, which allowed to analyze the degree of participation in the final accuracy of the survey of each of the considered factors. The results of this study demonstrate the source of errors, which provide the surveyor with the opportunity to efficiently and competently carry out pre-flight preparation and planning of fieldwork. The study and subsequent consideration of the factors affecting the accuracy of surveying with the use of an unmanned aerial vehicle are the basis for the subsequent development and formation of a methodology for using a geodesic quadcopter in the conditions of open-pit mining.
-
Date submitted2021-07-13
-
Date accepted2021-10-18
-
Date published2021-12-16
Prediction of the stress state of the shotcreting support under repeated seismic load
- Authors:
- Maksim A. Karasev
- Roman O. Sotnikov
The article assesses the impact of repeated blasts on the stress-strain state of the shotcreting support, which negatively affects the bearing capacity of the support and can lead to the formation of local rock falls in places of significant degradation of the shotcreting strength. Despite the fact that a single seismic load usually does not have a significant impact on the technical condition of the shotcreting support, repeated dynamic loading can lead to the development of negative processes and affect the safety. The article considers unreinforced and dispersed-reinforced shotcreting concrete as a shotcreting support. Models of deformation of rock and shotcreting support have been studied. To describe the deformation model of a rock mass, an elastic–plastic model based on the Hook-Brown plasticity condition has been accepted, which accurately describes the elastic-plastic behavior of a fractured medium. When performing the prediction of the stress-strain state of the shotcreting support, a model of plastic deformation of concrete with the accumulation of Concrete Damage Plasticity (CDP) was adopted, which allows to comprehensively consider the process of concrete deformation both under conditions of uniaxial compression and stress, and with minor edging draft. At the first calculation stage, a forecast of the seismic waves propagation in the immediate vicinity of the explosive initiation site was made. At the second stage, forecasts of the seismic waves propagation to the mine working and the stress-strain state of the support were made. On the basis of the performed studies, a methodology for assessing the impact of repeated blasts on the stress-strain state of the shotcreting support of the mine working is proposed.
-
Date submitted2021-03-13
-
Date accepted2021-05-21
-
Date published2021-09-20
Cadastral valuation of forest lands, taking into account the degree of development of their infrastructure
The article substantiates the need to improve methodology for cadastral valuation of forest lands and change the principles for calculating the rental rate of forest lands, on the basis of which the rent for the use of these lands will be determined in future. The methodology for determining the cadastral value of forest lands, taking into account the degree of development of their infrastructure, is presented. The infrastructure of lands of the forest fund is considered and an algorithm for assessing such infrastructure by means of geoinformation modeling is shown. A method for calculating a complex integral indicator (coefficient of infrastructure development) is presented, which is applicable to differentiate lands covered and not covered with tree vegetation, for their effective and rational management. The complex integral indicator determines the availability of forest plots, as it takes into account location of the forest fund infrastructure in relation to assessment plots, which makes it possible to obtain information about the time spent on covering the required distance. This methodology can be applied to assess the quality and condition of the existing infrastructure of the forestry sector in implementation of measures within the framework of the Strategy for the development of the forestry complex, providing for support and construction of infrastructure facilities on the forest fund lands. The method was tested in the Baltiysky district forestry of the Baltiysko-Belozersky taiga region. The results were as follows: the map of the forest fund infrastructure development within the boundaries of differentiation assessment according to the calculated integral indicator of infrastructure development was obtained; the regression model for calculating the rent rate taking into account the taxation value and integral indicator infrastructure development was received: the cadastral value of forest lands taking into account the developed model was calculated.
-
Date submitted2020-09-09
-
Date accepted2021-03-29
-
Date published2021-09-20
Developing features of the near-bottomhole zones in productive formations at fields with high gas saturation of formation oil
The article studies the formation features of the bottomhole zones in productive formations during operation of production wells in the north of the Perm Territory. Their distinctive feature is the high gas saturation of formation oil. The most widely used parameter in Russian and world practice – the skin factor was used as a criterion characterizing the state of the bottomhole zone. Analysis of scientific publications has shown that one of the main problems of applying the skin factor to assess the state of bottomhole zones is the ambiguity of interpretations of its physical meaning and the impossibility of identifying the prevailing factors that form its value. The paper proposes an approach to identifying such factors in the conditions of the fields under consideration, based on multivariate correlation-regression analysis. Choice of this tool is due to the complexity of the processes occurring in the “formation – bottomhole zone – well” system. When describing complex multifactorial processes, the chosen method demonstrates a high degree of reliability. For a large number of wells in the region, significant material was collected and summarized, including the results of determining the skin factor (1102 values) during hydrodynamic investigations, as well as data on the values of various geological and technological indicators, which can probably be statistically related to the value of the skin factor. A series of multidimensional mathematical models has been built; the skin factor was used as a predicted parameter, and data on the values of geological and technological indicators were used as independent indicators. Analysis of the constructed models is a key stage of this study. Set of parameters included in the multidimensional models, sequence of their inclusion and contribution to the total value of the achieved determination coefficient as the main indicator for the performance of the constructed models were studied. It has been established that the main factor influencing the state of the bottomhole zone is oil degassing. Significant differences in the formation features of the skin factor in the terrigenous and carbonate sediments at the fields under consideration have been determined.
-
Date submitted2020-06-16
-
Date accepted2021-03-29
-
Date published2021-09-20
Empirical regularities investigation of rock mass discharge by explosion on the free surface of a pit bench
- Authors:
- Igor A. Alenichev
- Ruslan A. Rakhmanov
Minimizing the discharge of blasted rock mass into the developed space of the pit is a very relevant area for study, as it allows to increase the processability of work and reduce the cost of mining. The article presents the results of experimental industrial explosions, during which the study of this issue was conducted. The main purpose of the work was to establish the key factors affecting the volume of rock mass discharge to the pit haulage berm. During the analysis of the world experience of research on this topic, the key factors affecting the formation of collapse and discharge – natural and technological – are identified. The method of conducting experiments and collecting data for analyzing the influence of technological parameters of location, charging and initiation of wells on the volume of rock mass discharge is described. It is established that the main discharge to the pit haulage berm is formed by the volume of rock mass limited by the prism of the slope angle. With a sufficient rock mass displacement from the edge of the bench crest towards the center of the block, only the wells of the 1st and 2nd rows participate in the discharge formation. Empirical dependences of the total volume of rock mass discharge on the length of the block along the bench crest, the specific consumption of explosives, the size of a rock piece P 50 and the rate of rock breaking are obtained. The obtained results can be used to design the parameters of the drilling and blasting operations (DBO), as well as to predict and evaluate the possible consequences of a mass explosion in similar mining and geological conditions.
-
Date submitted2020-08-03
-
Date accepted2020-12-13
-
Date published2021-06-24
Tectonic and magmatic factors of Li-F granites localization of the East of Russia
- Authors:
- Viktor I. Alekseev
We have investigated tectonic and magmatic factors of Li-F granites localization of the East of Russia. The study is based on the ideas of Far Eastern geologists about the deep structures of intraplate activity. A model of a source structure with mantle heat sources and ore-forming magmatic complexes was used. We carried out a special metallogenic analysis of the East of Russia as applied to the rare metal-tin-bearing formation of subalkaline leucogranites, including Li-F ones. Source structures are the main factor in the tectonic and magmatic development of the East of Russia, localization of ore-forming granites and the formation of rare-metal-tin ore regions. On deep layers of source structures there are areas of the mantle and earth's crust decompaction, heat, magmas and fluids sources, as well as granitoid cryptobatholiths. Relatively large massifs of leucogranites, small intrusions of tin monzonitoids and Li-F granites are concentrated near the modern surface. The source structures correspond to the rank of the ore region. The source structures in the South of the region are: Badzhalskaya, Miao-Chanskaya, Ippato-Merekskaya, Hogdu-Lianchlinskaya, Arminskaya, etc.; in the North: Pevekskaya, Kuiviveem-Pyrkakayskaya, Kuekvun-Ekiatapskaya, Iultinskaya, Telekayskaya, Central Polousnaya, Omsukchanskaya, etc. Three types of ore regions have been identified according to the degree of source structures and Li-F granites erosion. We have also outlined the patterns of source structures evolution and their place in the geological history of ore-bearing granites. A classification of source structures and its comparison with the classifications of regional intrusives and metallogenic subdivisions are proposed. It has been established that, despite the diversity of tectonic, geological and petrological settings in the East of Russia, the intrusions of Li-F granites are regulated by the same tectonic and magmatic factors. The tectonic and magmatic factors of Li-F granites localization in the East of Russia are identified and classified as geophysical, orogenic, geoblock, magmatic, metasomatic and disjunctive.
-
Date submitted2020-06-12
-
Date accepted2020-06-15
-
Date published2020-12-29
Analysis of project organization specifics in small-scale LNG production
- Authors:
- Pavel S. Tcvetkov
- S. V. Fedoseev
Gas industry plays an important role in the global energy sector, and in the coming decades amountsof natural gas production will only increase. One of the fastest growing trends in gas industry is the production of liquefiednatural gas (LNG), which is associated with the necessity to organize flexible systems of gas supply to the regions,remote from gas extraction sites. Industrial structure of LNG production includes projects, belonging to several different groups depending to their scale, in particular, small-scale production (SSLNG), cumulative production capacityof which is approximately 10 % from the industry-wide one. Economic aspects of implementing such projects remainunderexplored, which does not allow to draw objective conclusions regarding the prospects of their implementationin particular regions.This paper contains a review of publications, devoted to SSLNG project studies, aimed at identifying specifics oftheir organization compared to projects of greater scale. The results demonstrate that the majority of internationalcompanies classify projects as SSLNG, if their annual production capacity is below 0.5 million tonnes per annum.Specific capital costs, as well as implementation timelines of such projects, are several times lower than those of projects with greater production capacity, which reduces their risks and minimizes barriers to market entry. Furthermore,SSLNG is the most decentralized subsector in gas industry, aiming to cover the market due to a growing numberof projects, not their specific production capacity. These specific features define significant prospects of SSLNGdevelopment in Russia, both in the context of energy supply to remote regions and diversification of export deliveries.
-
Date submitted2020-05-24
-
Date accepted2020-05-29
-
Date published2020-06-30
Features of permeability anisotropy accounting in the hydrodynamic model
Important step in the construction of a geological and hydrodynamic model is to set the correct properties of the formations and further adapt the model to the historical development data. Main source of information on the geological properties of reservoirs is well logging data. Paper describes the application of the method for post-interpretation processing of logging data, with the help of which the lateral anisotropy value of the field site is found. Brief discussion on the algorithm for adapting the hydrodynamic model to the parameters of the formation using one reference well is given. Feature of the logging data application to study the phenomenon of permeability anisotropy is that this type of research is widespread, has sufficient information content, and the geophysical system itself does not require the inclusion of specialized instruments. Based on geophysical study, a volumetric model of the properties for oil and gas bearing formation is constructed, from which the permeability distribution is used, whose gradient allows establishing the directions of improved and deteriorated filtration properties. As a result, during adaption of the model, it was possible to achieve a difference in reserves between the geological and hydrodynamic models of 2.4 %, which is an acceptable deviation for further calculations. It was found that the direction of improved filtration properties has a northeastern direction at an angle of 35°, and the value of lateral anisotropy is 2.2. Obtained results of lateral anisotropy, taking into account the data on values of vertical anisotropy, are included in the field model, where it is planned to further study the effect of permeability anisotropy on formation productivity.