-
Date submitted2024-03-20
-
Date accepted2024-11-07
-
Date published2025-02-27
Analysis of the stress state of rocks transformation near a horizontal well during acid treatment based on numerical simulation
The article presents an overview of the assessment and modelling of the stress state of rocks in the near-wellbore zone of horizontal wells during acid stimulation of the formation for improving the efficiency of oil and gas field development. A numerical finite element model of near-wellbore zone of the reservoir drilled by a horizontal section was compiled using one of oil fields in the Perm Territory as an example. The distribution of physical and mechanical properties of the terrigenous reservoir near the well was determined considering transformation under the action of mud acid for different time periods of its injection. Multivariate numerical simulation was performed and the distribution of horizontal and vertical stresses in near-wellbore zone was determined with regard for different values of pressure drawdown and changes in stress-strain properties depending on the area of mud acid infiltration. It was found that a change in elastic modulus and Poisson's ratio under the influence of acid led to a decrease in stresses in near-wellbore zone. Analysis of the stress distribution field based on the Coulomb – Mohr criterion showed that the minimum safety factor of rock even after the effect of mud acid was 1.5; thus, under the considered conditions of horizontal well modelling, the reservoir rock remained stable, and no zones of rock destruction appeared.
-
Date submitted2021-12-20
-
Date accepted2024-05-02
-
Date published2024-08-26
A new formula for calculating the required thickness of the frozen wall based on the strength criterion
- Authors:
- Mikhail А. Semin
- Lev Yu. Levin
The study delves into the elastoplastic deformation of a frozen wall (FW) with an unrestricted advance height, initially articulated by S.S.Vyalov. It scrutinizes the stress and displacement fields within the FW induced by external loads across various boundary scenarios, notably focusing on the inception and propagation of a plastic deformation zone throughout the FW's thickness. This delineation of the plastic deformation zone aligns with the FW's state of equilibrium, for which S.S.Vyalov derived a formula for FW thickness based on the strength criterion. These findings serve as a pivotal launchpad for the shift from a one-dimensional (1D) to a two-dimensional (2D) exploration of FW system deformation with finite advance height. The numerical simulation of FW deformation employs FreeFEM++ software, adopting a 2D axisymmetric approach and exploring two design schemes with distinct boundary conditions at the FW cylinder's upper base. The initial scheme fixes both vertical and radial displacements at the upper base, while the latter applies a vertical load equivalent to the weight of overlying soil layers. Building upon the research outcomes, a refined version of S.S.Vyalov's formula emerges, integrating the Mohr – Coulomb strength criterion and introducing a novel parameter – the advance height. The study elucidates conditions across various soil layers wherein the ultimate advance height minimally impacts the calculated FW thickness. This enables the pragmatic utilization of S.S.Vyalov's classical formula for FW thickness computation, predicated on the strength criterion and assuming an unrestricted advance height.
-
Date submitted2023-03-14
-
Date accepted2023-10-25
-
Date published2024-04-25
Predictive assessment of ore dilution in mining thin steeply dipping deposits by a system of sublevel drifts
The purpose of research is the study of stress-strain state of marginal rock mass around the stope and predictive assessment of ore dilution with regard for changes in ore body thickness in mining thin ore deposits on the example of the Zholymbet mine. Study of the specific features of the stress-strain state development was accomplished applying the methodology based on numerical research methods taking into account the geological strength index (GSI) which allows considering the structural features of rocks, fracturing, lithology, water content and other strength indicators, due to which there is a correct transition from the rock sample strength to the rock mass strength. The results of numerical analysis of the stress-strain state of the marginal part of the rock mass using the finite element method after the Hoek – Brown strength criterion made it possible to assess the geomechanical state in the marginal mass provided there are changes in ore body thickness and to predict the volume of ore dilution. It was ascertained that when mining thin ore deposits, the predicted value of ore dilution is influenced by the ore body thickness and the GSI. The dependence of changes in ore dilution values on the GSI was recorded taking into account changes in ore body thickness from 1 to 3 m. Analysis of the research results showed that the predicted dimensions of rock failure zone around the stopes are quite large, due to which the indicators of the estimated ore dilution are not attained. There is a need to reduce the seismic impact of the blasting force on the marginal rock mass and update the blasting chart.
-
Date submitted2022-08-24
-
Date accepted2023-02-15
-
Date published2023-08-28
Modelling of the stress-strain state of block rock mass of ore deposits during development by caving mining systems
The article is devoted to the analysis of approaches to modeling the stress-strain state of a block rock mass in the vicinity of a single mine workings and in the area of rock cantilever influence during the development of the Khibiny apatite-nepheline deposits. The analysis of the existing in international engineering practice ideas about tectonic disturbances as a geomechanical element and the experience of predicting the stress-strain state of a block rock mass was carried out. On the basis of the analysis, the formulation of the basic modeling tasks is carried out and its main results are presented. Methodological recommendations for solving similar problems were developed.
-
Date submitted2021-10-31
-
Date accepted2023-03-02
-
Date published2023-12-25
Improvement of technological schemes of mining of coal seams prone to spontaneous combustion and rock bumps
On the example of the Alardinskaya mine, the problem of underground mining of seams prone to spontaneous combustion and rock bumps in the conditions of the Kondomsky geological and economic region of the Kuznetsk coal basin is considered. The contradictions in the requirements of regulatory documents for the width of the inter-panel coal pillars in the mining of seams with longwalls in conditions of endogenous fire hazard and in the mining of seams that are dangerous due to geodynamical phenomena are discussed. These contradictions impede the safe mining of seams using traditionally used layouts with the danger of spontaneous combustion of coal and rock bumps. A mining-geomechanical model is presented, which is used for numerical three-dimensional simulation of the stress-strain state of a rock mass with various layouts for longwall panels using the finite element method. The results of the numerical analysis of the stress state of the rock mass immediately before the rock bump are presented, and the main factors that contributed to its occurrence during the mining of the seam are established. A dangerous degree of stress concentration in the coal seam near the leading diagonal entries is shown, especially in conditions of application of abutment pressure from the edge of panels’ gob. The analysis of the features of stress distribution in the inter-panel pillar at different widths is carried out. Recommendations for improving the layout for the development and mining of coal seams that are prone to spontaneous combustion and dangerous in terms of rock bumps in the conditions of Alardiskaya mine have been developed. The need for further studies of the influence of pillars for various purposes, formed during the mining of adjacent seams, on the stress-strain state of previously overmined and undermined seams is shown.
-
Date submitted2022-07-15
-
Date accepted2022-12-13
-
Date published2023-02-27
Mathematical modelling of displacement during the potash ores mining by longwall faces
In favourable mining conditions, in particular at the Starobinskoye potash deposit (Belarus), longwall mining systems are used. They cause a high human-induced load on the subsoil, including intense deformation of the ground surface. The presented investigations are aimed at studying the dynamics of the ground surface displacement during the longwall face advance. Mathematical modelling was carried out in an elastic-plastic formulation with numerical implementation by the finite element method. The condition for the roof rocks collapse was opening of the contact between the seams when its boundaries were reached by shear fractures or formation of the tensile stresses area at the outcrop. With the working front advance, an increase in subsidence is observed, followed by its stabilization to a value determined by the process parameters of mining operations and the physical and mechanical properties of collapsed rocks. In this case, each point of the ground surface experiences sign-alternating horizontal deformations: when the front approaches, it causes tension, and when it moves away, compression. The obtained results of mathematical modelling are in good agreement with the data of instrumental measurements of the ground surface displacements, which indicates the adequate description of the rock mass deformation during the slice excavation of sylvinite seams by longwall faces.
-
Date submitted2022-05-18
-
Date accepted2022-07-21
-
Date published2022-11-10
Improving the method for assessment of bending stresses in the wall of an underground pipeline
- Authors:
- Ruslan V. Aginey
- Alexei A. Firstov
Brief information about modern methods for determining the bending stresses of the extended sections of underground main pipelines without access to the pipeline generatrix is given. The necessity of modernizing methods based on determining the configuration of the pipeline axis from the soil surface with subsequent calculation of bending stresses based on the obtained data is substantiated. A mathematical model that allows to calculate the optimal parameters for surveying the axis of the pipeline from the soil surface for a pipeline of arbitrary configuration and depth, when planning a study, is proposed. Bench tests of the BITA-1 pipeline finder were carried out to determine the error in measuring the depth of the pipeline axis. It is proved that the deviations of the pipeline finder data relative to the true values in narrow depth intervals follow a normal distribution and do not change their sign. The confidence intervals of the error in determining the depth of the pipeline axis for the BITA-1 device are presented.
-
Date submitted2021-04-06
-
Date accepted2022-04-27
-
Date published2022-07-13
Experimental study on the effect of rock pressure on sandstone permeability
The results of laboratory studies to determine the effect of effective stress on the permeability of sandstone are presented. During the test, the samples were subjected to a stepwise increase or decrease of the effective stress (at a constant pore pressure) in a specified step. The values of rock permeability at different values of effective stress were determined, and the influence of the grain size of the reservoir rock matrix on the character of the change in the sandstone permeability coefficient was also established. During the test, a decrease in permeability was observed with an increase in effective stress. It was found that as a result of gradual loading/unloading of the sandstone sample, the original permeability values were not restored, which indicates the beginning of the formation of residual strains in the rock. This effect should be taken into account when modeling field development because in the process of reserves extraction the effective stress acting on the reservoir rock skeleton changes, which results in a significant chang in rock permeability. The results of laboratory studies showed that the deviation of permeability in medium-grained sandstones relative to the initial value was greater than in medium- and fine-grained sandstones. The pressure sensitivity coefficient and constant of material, which are used in empirical relationships between permeability and effective stress, were numerically estimated. At the same time, the constant of material showed no such convergence, which indicates that the values of this parameter are individual for each rock.
-
Date submitted2021-07-05
-
Date accepted2022-01-24
-
Date published2022-04-29
Ensuring the excavation workings stability when developing excavation sites of flat-lying coal seams by three workings
- Authors:
- Oleg I. Kazanin
- Andrei A. Ilinets
On the basis of analysis of mining plans and field studies at mines of JSC SUEK-Kuzbass, it is shown that in conditions of increasing the size of excavation columns during the development of flat-lying coal seams the stress-strain state of the rock mass along the workings length changes significantly. The necessity of predicting the stress-strain state at the design stage of the workings timbering standards, as well as subsequent monitoring of the workings roof state and its changes in the mining operations using video endoscopes, is noted. The results of numerical studies of the stress-strain state of the rock mass during the development of excavation sites by three workings for various combinations of width of the pillars between the workings for mining-geological and mining-technical conditions of the “Taldinskaya-Zapadnaya-2” mine are provided. The stresses in the vicinity of the three workings are compared with the values obtained during the development of the excavation sites by double drift. A set of recommendations on the choice of the location of the workings, the width of pillars, timbering standards that ensure the stable condition of the workings throughout the entire service life at the minimal losses of coal in the pillars is presented.
-
Date submitted2021-10-27
-
Date accepted2022-01-24
-
Date published2022-04-29
Prediction of the geomechanical state of the rock mass when mining salt deposits with stowing
The technogenic impact of mining on the environment is analyzed and the transition to geotechnology with stowing to reduce the impact of mining operations is proposed. The results of the research work devoted to the justification of parameters of the development of salt deposits with stowing and the definition of the influence of stowing on the dynamics of deformation of the underworked rock massif are presented. The relevance of research aimed at creating a safe and efficient technology for the transition from systems with natural maintenance of stoping space to systems with stowing has been substantiated. The results of studies on qualitative and quantitative assessment of the state of the rock massif (by the finite element method using FLAC3D software), worked out by combines, are given and the dynamics of the impact of mining operations on the rock mass and the change in the maximum stresses during the hardening of the stowing in the chambers are revealed. The numerical modeling method is used to analyze the conditions of change in the state of the underworked rock mass, to establish the mechanisms of its deformation at various stages of development. It is recommended to use this approach for geotechnical assessment of the rock mass state in conditions of using development systems of different classes.
-
Date submitted2021-01-18
-
Date accepted2021-05-21
-
Date published2021-09-20
Improving the efficiency of the technology and organization of the longwall face move during the intensive flat-lying coal seams mining at the Kuzbass mines
The reasons for the lag of the indicators of the leading Russian coal mines engaged in the longwall mining of the flat-lying coal seams from similar foreign mines are considered. The analysis of the efficiency of the longwall face move operations at the JSC SUEK-Kuzbass mines was carried out. A significant excess of the planned deadlines for the longwall face move during the thick flat-lying seams mining, the reasons for the low efficiency of disassembling operations and the main directions for improving the technology of disassembling operations are revealed. The directions of ensuring the operational condition of the recovery room formed by the longwall face are considered. The recommended scheme of converged coal seams mining and a three-dimensional model of a rock mass to justify its parameters are presented. Numerical studies using the finite element method are performed. The results of modeling the stress-strain state of a rock mass in the vicinity of a recovery room formed under conditions of increased stresses from the boundary part of a previously mined overlying seam are shown. The main factors determining the possibility of ensuring the operational condition of the recovery rooms are established. It is shown that it is necessary to take into account the influence of the increased stresses zone when choosing timbering standards and organizing disassembling operations at a interbed thickness of 60 m or less. A sufficient distance from the gob of above- or undermined seams was determined to ensure the operational condition of the recovery room of 50 m, for the set-up room – 30 m. Recommendations are given for improving technology and organization of the longwall face move operations at the mines applied longwall mining of flat-lying coal seams with the formation of a recovery room by the longwall face.
-
Date submitted2020-12-02
-
Date accepted2021-04-21
-
Date published2021-06-24
Modeling the processes of deformation and destruction of the rock sample during its extraction from great depths
Article investigates the change in the geophysical properties of rocks in the process of extracting the rock sample from great depths. Evaluation of changes in effective elastic properties, porosity and permeability of rock samples during extraction was carried out by means of finite element modeling. Assessment of the critical dimensions and orientation of internal defects, leading to the destruction of the rock samples during extraction from great depths, has been made based on the methods of linear destruction mechanics. Approach that makes it possible to calculate the change in the mechanical properties, porosity and fracturing of reservoir rocks in the process of extracting the rock sample from depths to the surface is proposed. Use of refined data on the mechanical properties of recoverable rock samples makes it possible to increase the accuracy of digital geological models required for geological exploration, determination of reservoir properties and oil and gas saturation of a field, and development of oil and gas deposits. Application of such models is especially relevant at all stages of the fields development with hard-to-recover reserves.
-
Date submitted2020-05-08
-
Date accepted2020-06-12
-
Date published2020-12-29
Gas-dynamic roof fall during the potash deposits development
In the development of practically all potash salt deposits, the study of gas-dynamic phenomena (GDP) is one of the most difficult tasks to ensure mining safety. Sudden salt and gas outbursts, dynamic breakdown, which are accompanied by intense gas release and possible broken rock carry-over into the mine workings, are associated with GDP. Geological preconditions for the GDP development are often the layered structure of the salt rock mass, the presence of interlayers and layers of salt clays. For the conditions of the Usolsky potash plant mine, complex studies of factors that characterize the possibility of gas-dynamic roof fall of the stoping rooms were carried out. In mine studies, free gases pressure and the initial velocity of gas release in the rocks of the roof workings were determined. The obtained experimental estimations were used as a parametric basis for mathematical modeling of geomechanical processes under conditions of a near-contact accumulation of free gas. The deformation of a layered salt mass produced by a room development system was described by the model of an ideal elastic-plastic medium with internal friction. The parabolic envelope of Mohr circles was used as a plasticity criterion in the compression area. In the numerical implementation, the deformation of clay contacts was modeled by Goodman contact elements. Based on the results of multivariate numerical calculations, it is established that the main factors determining the possibility of implementing GDP are the additional gas pressure at the contact, the width of the workingspan, and the distance from the roof to the first gas-containing contact. With multi-level lamination of roof rocks, there is a danger of large sources of GDP formation and the mechanism of successive fall of layers in an instant mode is implemented.
-
Date submitted2019-07-17
-
Date accepted2019-10-09
-
Date published2020-04-24
Assessment of internal pressure effect, causing additional bending of the pipeline
Article justifies accounting for internal pressure effect in the pipeline, causing additional bending of the pipeline. According to some scientists, there is an erroneously used concept of the equivalent longitudinal axial force (ELAF) S x , which depends on working pressure, temperature stresses, and joint deformations of pipelines with various types of soils. However, authors of the article use ELAF S x concept at construction of mathematical model of stress-strain state (SSS) for complex section of the trunk pipeline, and also reveal it when analyzing the results of calculating the durability and stability of the pipeline. Analysis of SSS for calculated section of the pipeline was carried out for two statements of the problem for different values of operation parameters. In the first statement, effect of internal pressure causing bending of the pipeline is taken into account, and in the second it is neglected. It is shown that due to effect of ELAF S x at p 0 = 9.0 MPa, Dt = 29 °C extreme value of bend increases by 54 %, extreme values of bending stresses from span bending moment increase by 74 %, and extreme value of bending stresses from support bending moment double with regard to corresponding SSS characteristics of the pipeline. In case of neglecting the internal pressure effect causing additional bending of the pipeline (second statement of the problem), error in calculating the extreme value of bend is 35 %, extreme value of bending stresses from span bending moments is 44 %, and extreme value of bending stresses from support bending moments is 95 %.
-
Date submitted2019-03-25
-
Date accepted2019-05-23
-
Date published2019-08-23
Assessment of Rock-Burst Hazard in Deep Layer Mining at Nikolayevskoye Field
The paper presents results of conducted research using regional and local methods of forecast and control over geomechanical state of the rock mass at burst-hazardous Nikolayevskoye field, located in a geodynamically active region. The study subject is the ore mass of Nikolayevskoye field, characterized by man-induced and tectonic disturbances and high geodynamic activity. The aim of research was practical implementation of methods and instruments of forecast and control over geomechanical state of the burst-hazardous rock mass and safety improvement of mining operations. Exploitation practice of burst-hazardous fields demonstrates that forecast accuracy of hazardous rock pressure demands cutting-edge multi-level systems, where local methods and tools complement regional ones. A regional forecast of rock-burst hazard at Nikolayevskoye field was performed by means of seismoacoustic method using automated control system for rock pressure (ACSRP) «Prognoz-АDS». Local forecast was carried out using «Prognoz-L» device, geophysical (sample disking) method and visual observations of dynamic pressure manifestations in the mining tunnels. Quality assessment of stress-strain and burst state of the rock mass was performed using specialized software «PRESS 3D URAL». Integration of engineering and geomechanical data in the process of conducting research guarantees a relevant assessment of rock-burst hazard in various areas of the field at various stages of its development. Practical verification of the system, where local methods and tools complement regional ones, demonstrated satisfactory results at Nikolayevskoye mining plant, which makes it recommendable for other mining facilities extracting ore at great depths under similar conditions of active geodynamic processes.
-
Date submitted2019-03-11
-
Date accepted2019-05-06
-
Date published2019-08-23
Estimation Method for Vector Field Divergence of Earth Crust Deformations in the Process of Mineral Deposits Development
- Authors:
- B. T. Mazurov
- M. G. Mustafin
- A. A. Panzhin
An essential requirement for effective and safe deposit development is good geomechanical software. Nowadays software packages based on finite element method are used extensively to estimate stress-strain state of the rock mass. Their quality use can only be assured if boundary conditions and integral mechanical properties of the rock mass are known. In mining engineering this objective has always been achieved by means of experimental observations. The main source of information on initial and man-induced stress-strain state of the rock mass is natural measurement of displacement characteristics. Measurement of geodetic data (coordinates, heights, directions) in the period between alteration cycles allows to plot a field of displacement vectors for the points in question. Taken together, displacement vectors provide information on the objective stress-strain state of the Earth crust. Basing on it, strain tensors, displacement components, directions and rates of compression and tension can be calculated in the examined area. However, differential characteristics of any physical vector field – namely, curl and divergence – need to be taken into account. Divergence is a single value (scalar) associated with a single point. Vector field as a whole can be described with divergence scalar field. Divergence indicates the sign (positive or negative) of volume changes in the infinitesimal region of space and characterizes vector flux in the nearest proximity and in all directions from a given point. In the paper authors propose a method to estimate divergence using discrete geodetic observations of displacement occurring on the surface of examined territory. It requires construction of formulas that model vector field for any point of the area. It is proposed to use power polynomials that describe displacement in three directions (x, y, z). These formulas allow to estimate field vectors in any given point, i.e. to form vector tubes. Then areas of input and output cross-section, as well as divergence values are calculated. This increases the quality of geodetic observation and provides opportunities for more precise modeling of the rock mass disrupted by mining operations, using modern software packages.
-
Date submitted2018-11-09
-
Date accepted2019-01-22
-
Date published2019-04-23
Determining the stability of the borehole walls at drilling intervals of loosely coupled rocks considering zenith angle
- Authors:
- P. A. Blinov
During development of drilling projects, a whole array of data is needed considering the properties of rocks and the conditions of their bedding. Accounting for geomechanical processes occurring in the near-wellbore zone allows avoiding many complications associated with the violation of the wellbore walls stability at all stages of its construction and operation. Technological and technical factors such as vibration and rotation of the drilling string, formation of launders during the descent and ascent of the assembly, pressure pulsation during the start and stop of pumps, hydrostatic and hydrodynamic pressure of the drilling fluid, its composition and properties, have a great influence on the stress-strain state of the medium opened by the well. The washing fluid circulating in the well should provide backpressure to the reservoir, not interact with the rocks chemically, colmatage channels in porous and fractured rocks, preventing penetration of the mud into the medium, by creating an impermeable barrier at drilling clay seams that are prone to swelling, cracking, etc. The article discusses the method for determining the stability of the directed well walls, taking into account the penetration of drilling mud into the pores and fractures of rocks. The technique will allow adjusting the zenith angle of the well during the workout of an unstable interval at the design stage, or selecting a drilling fluid composition to ensure fail-safe drilling.
-
Date submitted2018-07-18
-
Date accepted2018-09-22
-
Date published2018-12-21
Forecasting rock burst hazard of tectonically disturbed ore massif at the deep horizons of Nikolaevskoe polymetallis deposit
- Authors:
- D. V. Sidorov
- M. I. Potapchuk
- A. V. Sidlyar
The subject of the research is the stress-strain and rock burst hazardous state of the ore massif of the Nikolaevskoe polymetallic deposit, formed under the influence of complex mining-geological and mining-technical factors. The purpose of the research is to establish the peculiarities of the formation of technogenic stress fields at the deposit, which is characterized by a block structure, a complex tectonic system and the presence of a large volume of developed spaces. Volumetric geodynamic modeling of the stress-strain state of the massif at different stages of the development of the deep horizons of the deposit was carried out by collecting information on the structure, properties and geodynamic state of the rock mass. The assessment of stress changes taking into account the effect of hypsometry, the configuration of the selvages, the physical-mechanical properties of the ore deposit and host rocks, the presence of tectonic disturbances was made using the developed numerical algorithms, the automation equipment of the initial data and the PRESS 3D URAL software. The simulation made it possible to establish that tectonic faults in the massif lead to a qualitative change in the stress-strain state in certain parts of the ore massif and in the pillars, namely, the reduction of stresses along the tectonic faults and their growth in nearby pillars. The identified features of the distribution of stresses in the tectonically disturbed rock massif of the Nikolaevskoe deposit will allow to identify in advance potentially hazardous areas both at the planning stage of mining operations and during development, as well as to work out effective rock burst measures to increase the safety of mining. The results of research can be used in enterprises with similar mining-geological and mining-technical conditions.
-
Date submitted2015-07-14
-
Date accepted2015-09-09
-
Date published2016-02-24
Engineering and geomechanical forecast for waste disposal in underground caverns including earthquake-prone zones
- Authors:
- O. V. Kovalev
The article aims at obtaining representative scientifically based data to determine parameters of a necessary-safe condition of the rock massif (RM) in underground waste diposal caverns zones, including earthquake-prone zones. The main requirements for underground caverns for hazardous waste disposal and for their construction technology are described. The subject of the research is underground solution caverns in halogen rocks. Data for justification of safe waste disposal conditions in underground salt caverns and its stages are presented. A complex approach to the solution of the research problem is described. The main aspects of dynamic influence of seismic waves on underground caverns stability are considered. Taking into account seismic-risk zoning data on the research region some significant parameters of a possible seismic impact on the experimental cavern are calculated. The article points out the necessity of superincumbent rock and surface displacement assessment for the experimental site zone using the suggested complex approach and including the analysis of surveying data and results of rock mass geomechanical modeling.
-
Date submitted2015-07-11
-
Date accepted2015-09-17
-
Date published2016-02-24
The mechanism of rock burst leading to ground destruction of mine openings
- Authors:
- M. G. Mustafin
The article deals with the main issues of studying of one type of rock bursts which lead to gound destruction of coal mine openings. The research is focused on rock burst prediction. Some cases of rock bursts are analised. The paper points out factors affecting this kind of rock failure. It also presents some simulation models and numerical examples. The results of the research show that it is possible to plan safe mining operations under different mining and geological conditions.
-
Date submitted2014-12-28
-
Date accepted2015-02-21
-
Date published2015-12-25
Modeling of rock massif geomechanical state at gas extraction from coal seams
- Authors:
- M. G. Mustafin
The article describes the method of modeling a coal seam stress-strain state and an enclosing rock massif when degasified. An approach to defining the model input parameters, calculated with the porosity and gas pore pressure coefficient, was shown. The importance of preliminary calculations, indicating possible coal seam shrinkage and surface subsidence was underlined. It shows formation mechanism for coal seam zones with elevated gas pressure, where gas recovery is efficient.
-
Date submitted2014-10-08
-
Date accepted2014-12-11
-
Date published2015-08-25
Modeling of geomechanical processes in ore mass using physically nonlinear model
- Authors:
- A. G. Protosenya
The aim of the article is to develop a method of forecasting the state of stress of the ore mass around excavations for ores of weak and medium strength. The paper presents experimental studies on the deformation of ore samples of low and medium strength in the forging equipment in conditions of volume stress state. A physically nonlinear model is used to describe the deformation process of ore mass. The study of the stress state of physically nonlinear ore mass around excavations of round and valuated cross-sections is performed. Values of coefficients of tangential stress concentrations on excavation contour are found for different types of ore. Solutions to physically nonlinear problems in preparatory excavations in the development of the Yakovlevskiy deposit of rich iron ore using a slicing method are considered. Methods for forecasting the stress state in rock mass around mine excavations can be used to assess their stability in the mining of ore of low and medium strength at the Yakovlevskiy iron ore deposit and in the rock and soil masses.
-
Date submitted2009-10-23
-
Date accepted2009-12-10
-
Date published2010-09-22
Geomechanical substantiation of projects of ore deposits mining
- Authors:
- V. V. Zubkov
- A. A. Filinkov
The paper presents the monitoring system for better geodynamic safety in mining of mineral deposits. The suggested system of geodynamic monitoring allows us to evaluate the stress state of ore massif for the planned variant of mining and to give recommendations on the safe deposit mining. Based on the analysis of the modeling data, consideration was given to one of the variants of geomechanical substantiation of the project of ore deposit mining.
-
Date submitted2009-10-14
-
Date accepted2009-12-03
-
Date published2010-09-22
Some geomechanical aspects in the development of calculation methods of rock pressure in permanent mine workings
- Authors:
- A. M. Kozel
The paper deals with the particular features of the stress-strain state and mechanical condition of the rocks surrounding the permanent mine workings; they should be taken into account in the development and updating of standards and calculation methods to ensure the stability of these workings.
-
Date submitted2009-10-02
-
Date accepted2009-12-03
-
Date published2010-09-22
Particular formation of higher rock pressure zones with intensive mining of contiguous seams at coal mines of the «Suek-Kuzbass» CO
- Authors:
- A. I. Paltsev
- V. V. Zubkov
- N. V. Krotov
The problem of mining the suites of contiguous coal seams is considered. The sequential manner of seams mining essentially has influence on change of rock and gas pressure. The results of calculation and construction of borders of zones of higher rock pressure are presented. The analysis of conditions of hazardous zones formation is given.