-
Date submitted2024-03-20
-
Date accepted2024-11-07
-
Date published2025-02-27
Analysis of the stress state of rocks transformation near a horizontal well during acid treatment based on numerical simulation
The article presents an overview of the assessment and modelling of the stress state of rocks in the near-wellbore zone of horizontal wells during acid stimulation of the formation for improving the efficiency of oil and gas field development. A numerical finite element model of near-wellbore zone of the reservoir drilled by a horizontal section was compiled using one of oil fields in the Perm Territory as an example. The distribution of physical and mechanical properties of the terrigenous reservoir near the well was determined considering transformation under the action of mud acid for different time periods of its injection. Multivariate numerical simulation was performed and the distribution of horizontal and vertical stresses in near-wellbore zone was determined with regard for different values of pressure drawdown and changes in stress-strain properties depending on the area of mud acid infiltration. It was found that a change in elastic modulus and Poisson's ratio under the influence of acid led to a decrease in stresses in near-wellbore zone. Analysis of the stress distribution field based on the Coulomb – Mohr criterion showed that the minimum safety factor of rock even after the effect of mud acid was 1.5; thus, under the considered conditions of horizontal well modelling, the reservoir rock remained stable, and no zones of rock destruction appeared.
-
Date submitted2023-11-02
-
Date accepted2024-09-24
-
Date published2025-02-12
Mercury contamination of sediments at Indonesia Ciujung watershed: contribution of artisanal small-scale gold mining
Artisanal small-scale gold mining is the largest artificial source of mercury pollution and has been a very common problem recently. This study examined the contribution of Hg release due to artisanal small-scale gold mining in contaminating the sediment of the watershed in Indonesia. Different from other methods, we measured Hg pollution using the stable isotopes of carbon and nitrogen. This report is the first time analytical reports in Indonesia since most papers focus primarily on only detecting heavy metals in river water and sediments, neglecting deep research on Hg pollution and resources. The findings of this study indicate that artisanal and small-scale gold mining activities, located in the upstream areas of the tributaries that act as point sources, are the primary source of mercury in the sediment of the Ciujung watershed. The isotopes δ13C and δ15N successfully trace the Hg-contaminated sediment in the Ciujung watershed derived from the Cisimeut and Ciberang Rivers based on soil organic matter. The biological effect showed the Hg concentration in most of the sampling sites exceeded the Effects-range medium and Probable effect limit values. The Risk quotient values of Hg indicated the Hg pollution had a possibility effect on the benthic organism. Several limitations have also been added in this study and needs for further investigation.
-
Date submitted2023-10-31
-
Date accepted2024-11-07
-
Date published2025-01-24
Specifics of magnetotelluric studies in Antarctica
One of the priority areas of scientific research in Antarctica is the study of its deep structure. Most of the continent is covered with a thick ice sheet, so the main geoscientific data are acquired using geophysical methods, among which magnetotelluric (MT) ones have the greatest penetration depth and insignificant environmental impact. The possibility of acquiring high-quality MT data in the conditions of the sixth continent has long been questioned. The work is aimed at studying the specifics of magnetotelluric survey in Antarctica. The following tasks were set: to summarize the world experience of studying Antarctica using MT sounding methods; to identify factors that negatively affect the high-quality data acquisition; to determine methods for minimizing the influence of these factors. The article analyses geophysical studies conducted by the magnetotelluric sounding method in the Antarctic region from 1964 to the present. The application of the method is complicated by the following: extremely low temperature affects the drop in the batteries capacity, freezing of the non-polarizing electrodes solution, and changes in the strength properties of materials. Electromagnetic noise occurs during strong winds; proximity to the magnetotelluric field source can violate the plane wave principle on which the method is based. The ice sheet covering most of Antarctica does not allow acquiring optimal values of the contact resistance of the electrode grounding; the extended coastline distorts the acquired data. Studies of the influence of factors complicating the MT sounding method in the coastal and central parts of Antarctica made it possible to formulate recommendations for preparing equipment and adapting the work procedure, modifying the processing flow and a set of measures to ensure safety, the implementation of which will both allow safe performance of geophysical investigations and high-quality data acquisition.
-
Date submitted2024-05-03
-
Date accepted2024-09-05
-
Date published2024-11-12
Platinum group elements as geochemical indicators in the study of oil polygenesis
This study examines elements of the platinum group (PGE), primarily platinum and palladium, as geochemical indicators in the investigation of oil polygenesis. It has been found that, like other trace elements such as nickel, vanadium, and cobalt, platinum group elements and gold can occur in oil fields at both background levels and in elevated or even anomalously high concentrations. The objective of this research is to analyze PGE and trace elements as geochemical markers to identify the geological factors, including endogenous processes, responsible for these unusually high concentrations in oil. A comprehensive review of the literature on this subject was conducted, along with new data on the presence of precious metals in oils from Russia and globally. The study explores the geological mechanisms behind elevated PGE concentrations in oils, utilizing atomic absorption spectroscopy with atomization in the HGA-500 graphite furnace to measure PGE content. Previously, the tellurium co-deposition method (ISO 10478:1994) was used to isolate noble metals from associated elements. Possible geological origins of abnormally high concentrations of platinum metals in oils have been identified. These include endogenous factors such as the spatial proximity of oil fields to ultrabasic rock massifs, the effects of contact-metasomatic processes, and influences from mantle dynamics. Moreover, data concerning mantle elements can serve as indicators of the depth origins of certain hydrocarbon fluids, thus contributing to the study of oil polygenesis.
-
Date submitted2024-04-12
-
Date accepted2024-09-05
-
Date published2024-11-12
Promising reagents for the extraction of strategic metals from difficult-to-enrich mineral raw materials
The need of the mining and processing industry for new types of directional reagents is due to the deterioration of the material composition of the processed ores. Low Au content (less than 0.5-1.0 g/t), finely dispersed Au inclusions (0.1-10.0 microns) in the ore, similar properties of the separated minerals have an extremely negative effect on flotation performance when using traditional reagents, which leads to significant losses of valuable metal with enrichment tailings. Expanding the range of domestic flotation reagents based on the latest achievements of fundamental research and their targeted application at mining and processing companies will compensate for the negative impact of the mineral composition of raw materials and ensure maximum extraction of strategic metals from difficult-to-enrich ores. The use of modern research methods (scanning electron and laser microscopy, UV spectrophotometry, XRF and chemical analysis) made it possible to visualize the adsorption layer of new reagents-collectors of a number of dithiocarbamates with different structures of a hydrocarbon radical and an organic modifier on the surface of gold-containing sulfides. The amount of adsorbed reagents on the surface of minerals has been experimentally determined. The specific features of the fixation of reagents on minerals of various compositions led to optimal correlations of their consumption in the flotation process. Scientifically based reagent regimes ensured an increase in the gold content in the concentrate and a decrease in the loss of gold with tailings by 5-6 % during flotation enrichment of the refractory ore of the Malinovskoe deposit.
-
Date submitted2022-03-01
-
Date accepted2024-06-03
-
Date published2024-12-25
Study of the possibility of using high mineralization water for hydraulic fracturing
The results of laboratory studies aimed at developing hydraulic fracturing fluid based on alternative sources of high mineralization water are presented. It is shown that Cenomanian sources have the most stable mineralization parameters, while bottom water and mixed waters collected from pressure maintenance systems differ significantly in their properties, with iron content varying several times, and hardness and mineralization undergoing substantial changes. The quality of the examined hydraulic fracturing fluids based on alternative water sources is confirmed by their impact on residual permeability, as well as residual proppant pack conductivity and permeability. The experimental results show similar values for these parameters. The comprehensive laboratory studies confirm the potential for industrial use of high mineralization water in hydraulic fracturing operations.
-
Date submitted2023-03-01
-
Date accepted2024-06-03
-
Date published2025-02-25
Lamprophyres of the Peshchernoe gold deposit, their geological position, material composition, and metasomatic alterations (Northern Urals)
The article presents the first data on biotite-hornblende lamprophyres discovered at the Peshchernoe gold deposit. We consider the geological position of lamprophyre dikes in the deposit structure and the relationship of these rocks with tectonically weakened and mineralized zones. The data on the structural position of mineralized zones, faults, dike bodies, metasomatic halos, and host volcanogenic-sedimentary rocks confirm the tectonic nature of the Peshchernoe deposit alteration system. Lamprophyre dikes are pre-ore, as evidenced by the superimposed metasomatic mineral associations. We assume that dikes of andesitic rocks, lamprophyres, and subsequently hydrothermal fluids, including ore-bearing ones, were intruded along the fault zone of northeastern strike at different geological times. The description of mineralogical and chemical transformations of lamprophyres, which occurred as a result of alteration, is given. Two stages of metasomatism are distinguished: carbon dioxide (beresitization-listvenitization) and subsequent alkaline (sodic metasomatism). During carbon dioxide metasomatism, dark-coloured minerals are replaced by chlorite, albitization and sericitization of plagioclase occur, and ferruginous dolomite is formed under the influence of a significant supply of CO2. Alkaline (sodic) metasomatism is superimposed on the mineral metasomatic paragenesis of the first stage. We consider metasomatic zoning during sodic metasomatism, manifested in one of the spessartite dikes. Chlorite and relics of magmatic dark-coloured minerals are replaced by magnesite, the supply of Na leads to the appearance of newly formed albite, and the supply of S leads to the formation of pyrite, which concentrates iron from other minerals. As a result of the sodic metasomatism, iron content in carbonates decreases in the direction from the outer metasomatic zone to the inner one. We conclude that it was the alkaline-sulphide sodium solutions that performed the ore-bearing function, and beresitization and listvenitization prepared a favourable environment for ore deposition.
-
Date submitted2023-07-07
-
Date accepted2023-09-20
-
Date published2024-02-29
Isotherm and kinetic adsorption of rice husk particles as a model adsorbent for solving issues in the sustainable gold mining environment from mercury leaching
One of the techniques used in extracting gold in small-scale gold mining is mercury amalgamation. However, the use of mercury presents significant health and environmental hazards, as well as suboptimal efficiency in gold extraction. This study explores the possibility of the use of rice husk as a prototype adsorbent for mercury removal from its leaching in mining environments. To support the analysis, the rice husk adsorbent was characterized by Fourier-transform infrared spectroscopy, scanning electron microscopy, electron dispersive X-ray spectroscopy, atomic absorption spectrophotometers and Brunauer − Emmett − Teller analysis. To investigate the removal of Hg from aqueous solutions, batch adsorption experiments were conducted, and the efficiency was optimized under various parameters such as contact time, rice husk dosage, and initial concentration of mercury. Kinetic and isotherm investigations were also carried out to gain a better understanding of the adsorption properties. The kinetic adsorption was analyzed using the pseudo-first-order and pseudo-second-order. Furthermore, the isotherm adsorption was analyzed using ten adsorption isotherm models (i.e., Langmuir, Freundlich, Temkin, Dubinin – Radushkevich, Flory – Huggins, Fowler – Guggenheim, Hill – de Boer, Jovanovic, Harkin – Jura, and Halsey). The amount of mercury absorption increased with increasing contact time, adsorbent mass, and initial concentration of mercury. The pseudo-second-order kinetic model is the best model that can be applied to describe the adsorption process. Analysis of the adsorption results obtained shows that the adsorption pattern is explained through the formation of a monolayer without any lateral interaction between the adsorbate and adsorbent. In addition, the formation of multilayers due to inhomogeneous pore distribution also occurs which causes a pore filling mechanism. We found that the isotherm phenomena are near the Jovanovic models with the maximum adsorption capacity) of rice husk found to be 107.299 mg/g. As a result, rice husk could be a promising option for wastewater treatment due to its fast and efficient removal capacity, as well as its affordability and eco-friendliness. The predicted thermodynamic studies using the Flory – Huggins isotherm model show that the adsorption process is endothermic, spontaneous, and physisorption. The impact shows that the utilization of rice husk can be used and fit for the current issues in the sustainable development goals (SDGs).
-
Date submitted2021-04-15
-
Date accepted2022-09-06
-
Date published2023-10-27
Gold-rare metal and associated mineralization in the western part of Bolshevik Island, Severnaya Zemlya archipelago
The presented studies are aimed to determine the formation patterns of the gold-rare metal mineralization within one of the most inaccessible Arctic islands of the Russian Federation, Bolshevik Island of the Severnaya Zemlya archipela-go. The relevance of the work is determined by the high probability of discovering a significant in terms of metal reserves deposit, which is proved by many researchers on the example of known large deposits to be a typical feature of sites with gold-rare metal formation. Obviously, only the possibility of discovering and subsequent development of a deposit of a highly liquid type of mineral, gold, can ensure the profitability of mining production on Severnaya Zemlya. It is established that the main geological, mineralogical, and geochemical features of the gold-rare metal mineralization in the Kropotkinsko-Nikitinskaya metallogenic zone of Bolshevik Island correspond to that of similar ore sites in Russia and the world. The occurrences of other formation types revealed in this metallogenic zone suggest a certain zoning in their distribution: mineralization is located in the apical parts of granitoids and in the nearest halo of hornfelses. At a distance, with an exit from the hornfelsed zone, there are occurrences of a cassiterite-sulphide formation with elevated gold and silver content at the top of the ore column, together with an increased amount of polymetallic ores. Occurrences of gold-quartz and gold-sulphide-quartz formations are localized in fault zones, as a rule, farther from granitoids. The total vertical range of gold mineralization exceeds 300 m. The assignment of all types of mineralization in the Kropotkinsko-Nikitinskaya metallogenic zone of Bolshevik Island to a single hydrothermal process is emphasized by the similar isotope composition of lead galena from heterogeneous occurrences, which determines the age of all mineralization at 200-300 Ma.
-
Date submitted2023-07-04
-
Date accepted2023-09-20
-
Date published2023-10-27
Structure maintenance experience and the need to control the soils thermal regime in permafrost areas
- Authors:
- Anatolii V. Brushkov
- Andrei G. Alekseev
- Svetlana V. Badina
- Dmitrii S. Drozdov
- Vladimir A. Dubrovin
- Oleg V. Zhdaneev
- Mikhail N. Zheleznyak
- Vladimir P. Melnikov
- Sergei N. Okunev
- Aleksei B. Osokin
- Nikolai A. Ostarkov
- Marat R. Sadurtinov
- Dmitrii O. Sergeev
- Roman Yu. Fedorov
- Konstantin N. Frolov
The risks of reducing the stability of buildings and structures are increasing in conditions of climate change and the active development of the territories under the influence of natural and anthropogenic factors. The main causes include: loss of the bearing capacity of frozen soils, various geocryological processes, errors at the stages of design, construction and operation of facilities. Main actual task when conducting research and industrial operations in the cryolithozone is monitoring and, if necessary, managing thermal processes in the permafrost layers interacting with facilities. In this article the obtained positive experience of various technologies applying at various stages of the life cycle of civil and industrial facilities was analyzed. It helps to eliminate or prevent the structure deformation or destruction under the influence of climate change. The methods of permafrost stabilization used in the oil and gas industry in process of industrial infrastructure development of the fields have been studied – freezing (cooling) of foundation soils during construction on heterogeneous foundations. The solution to the problems of minimizing accidents when locating production wells in the permafrost zone of the Yamal Peninsula is considered using the example of an oil and gas condensate field and restoring of the temperature regime of perennial unfrozen soils in areas of valve units of main gas pipelines. An assessment of methods used to maintain the industrial and residential infrastructure within the northern municipalities that ensure the functioning of the fuel and energy complex of the Russian Federation in the Arctic was made. The systems of thermal stabilization in the foundations of buildings and industrial facilities built and operated on permafrost soils allow to fully use the high strength and low deformability of frozen grounds. It ensures the state's long-term plans of the industrial development in the Arctic.
-
Date submitted2022-06-27
-
Date accepted2023-06-20
-
Date published2023-12-25
Analysis of the problems of high-quality drinking water extraction from underground water intakes on Vysotsky Island in the Vyborg district of the Leningrad region
This article presents the results of drilling, experimental filtration work and laboratory studies aimed at assessing the resources and quality of groundwater in the licensed area of Vysotsky Island located in the Leningrad region, in the Gulf of Finland in accordance with the requirements of regulatory documents. Analysis of the results of hydrochemical studies and their comparison with data on water intakes in adjacent areas gives the right to conclude that it is possible to classify a hydrogeological unit as a different type of resource formation than those located in the surrounding areas. Groundwater in this area is confined to an unexplored deep fractured regional high-pressure zone. According to the received data, the explored water intake can be attributed to a unique groundwater deposit, which has an uncharacteristic composition of groundwater in the north of the Leningrad region, which may be due to the mixing of modern sediments and relict waters of the Baltic glacial lake. The stability of groundwater characteristics is confirmed by long-term monitoring.
-
Date submitted2022-06-20
-
Date accepted2022-09-06
-
Date published2022-11-03
Adaptive approach formation using machine vision technology to determine the parameters of enrichment products deposition
In this paper, an adaptive approach has been developed for automatic initialization of the thickening curve using machine vision technology, which makes it possible to determine with high accuracy the material parameters necessary for the design of thickening and clarification apparatuses. Software has been developed that made it possible to search for the coordinates of the condensation critical point in automatic mode. Studies on two samples of materials (tailings of apatite-containing ores and gold-bearing concentrate) were carried out and made it possible to statistically prove the reproducibility of the results obtained using the parametric criteria of Fisher and Bartlett. It has been established that the deposition curves are approximated with high accuracy by the Weibull model, which, together with the piecewise linear approximation, makes it possible to formalize the method for determining the critical point coordinates. The empirical coefficients of the Weibull model for two samples are found, and the final liquefaction and settling rates of the studied materials are determined.
-
Date submitted2021-05-27
-
Date accepted2022-09-06
-
Date published2022-11-10
Application of resonance functions in estimating the parameters of interwell zones
It is shown that the use of force resonance leads to the effect of “shaking” the formation, followed by breaking up the film oil and involving it in the further filtration process. For the first time in oilfield geophysics, the concept of passive noise-metering method is justified for monitoring oil and gas deposit development by measuring the quality factor of the contours in the point areas of formation development channels in interwell zones. It is established that determining the depth of modulation for the reactive substitution parameter of the linear FDC chain is crucial not only for determining the parametric excitation in FDC attenuation systems, but also without attenuation in the metrological support for the analysis of petrophysical properties of rock samples from the wells. It is shown that based on the method of complex amplitudes (for formation pressure current, differential flow rates, impedance), different families of resonance curves can be plotted: displacement amplitudes (for differential flow rates on the piezocapacity of the studied formation section), velocities (amplitudes of formation pressure current) and accelerations (amplitudes of differential flow rates on the linear piezoinductivity of the FDC section). The use of predicted permeability and porosity properties of the reservoir with its continuous regulation leads to increased accuracy of isolation in each subsequent sub-cycle of new segment formation in the FDC trajectories, which contributes to a more complete development of productive hydrocarbon deposits and increases the reliability of prediction for development indicators.
-
Date submitted2022-04-29
-
Date accepted2022-07-21
-
Date published2022-11-10
Deep structure, tectonics and geodynamics of the Sea of Okhotsk region and structures of its folded frame
The use of the zonal-block model of the earth's crust for the construction of regional tectonic schemes and sections of the earth's crust based on a complex of geological and geophysical data makes it possible to consider the resulting maps and sections as tectonic models. The main elements of such models are blocks with an ancient continental base and interblock zones formed by complexes of island arcs, an accretionary prism, or oceanic crust. The developed geotectonic model of the Sea of Okhotsk region reflects the features of the deep structure, tectonics, and geodynamics. The Cimmerian Novosibirsk-Chukotka, Verkhoyansk-Kolyma, Kolyma-Omolon, and Amur folded regions and the Alpides of the Koryak-Kamchatka and Sakhalin-Sikhote-Alin folded regions are developed along the northern, western, and southern boundaries of the Sea of Okhotsk megablock with a continental crust type. From the east, the megablock is limited by oceanic basins and island arcs.
-
Date submitted2022-03-21
-
Date accepted2022-06-15
-
Date published2022-07-26
Ti-Fe-Cr spinels in layered (stratified) complexes of the western slope of the Southern Urals: species diversity and formation conditions
- Authors:
- Sergey G. Kovalev
- Sergey S. Kovalev
Materials on geochemistry and ore Fe-Ti-Cr mineralization of rocks composing layered (stratified) bodies of the western slope of the Southern Urals are presented. A detailed analysis showed similarity in the redistribution of REE, noble metals, and Fe-Ti-Cr mineralization of practically all parameters in rocks of the Misaelga and Kusin-Kopan complexes. It has been established that the parameters of metamorphism, which influenced components redistribution in Fe-Ti-Cr minerals of the layered complexes, correspond to Misaelga – T = <550-750 °С, P = 0.1-2.8 kbar, Kusin-Kopan – T = <550-630 °С, P = 0.3-0.7 kbar, and Shuidinsky complexes – T = <550-760 °С, P = 0.5-2.5 kbar. The result of modelling the melt crystallization process showed that the Kusin-Kopan complex is an intrusive body with an ultramafic horizon in the idealized cross-section. Due to collisional processes, the lower part of the intrusion has been detached from the upper part. The proposed structure of the Kusin-Kopan complex sharply increases its prospects for such types of minerals as platinum group minerals + sulphide copper-nickel mine-ralization and/or chromites.
-
Date submitted2022-03-03
-
Date accepted2022-04-27
-
Date published2022-07-26
Peculiarities of rare-metal mineralization and genetic relationship of mineral associations in the eastern rim of Murzinsko-Aduysky anticlinorium (the Ural Emerald Belt)
- Authors:
- Mikhail P. Popov
The paper presents features of the location and composition, as well as a generalization of data on the age of rare-metal mineralization developed at the deposits and occurrences of rare metals and gemstones in the eastern rim of Murzinsko-Aduysky anticlinorium, within the Ural Emerald Belt, which is a classic ore and mineralogical object and has been studied for almost two hundred years. With a significant number and variety of prospecting, research and scientific works devoted mainly to emerald-bearing mica complexes and beryl mineralization, as well as rare-metal pegmatites, scientific literature has so far lacked generalizations on the formation of numerous mineral associations and ore formations that represents a uniform genetic process in this ore district. The aim of the work is a comprehensive geological-mineralogical analysis of mineral associations of the eastern rim of Murzinsko-Aduysky anticlinorium and studying their age, formation conditions and characteristic features to determine the possibility of expanding and using the mineral resource base of the Urals through developing new prognostic and prospecting criteria for rare-metal and gemstone ore formations and creating the new devices for promising objects prospecting
-
Date submitted2022-04-06
-
Date accepted2022-06-15
-
Date published2022-07-26
Geological and structural position of the Svetlinsky gold deposit (Southern Urals)
The paper presents the geological and structural position of the large Svetlinsky gold deposit in the Kochkar anticline (Southern Urals), localized in the zone of the Late Paleozoic (D 3 ) deep thrust of the western dip. The study confirms and clarifies the notion of its multiphase and polychronism. The thrust caused bending moments in its wings, subsidence of the lying crust, emergence of a shallow marine basin with rapid accumulation of terrigenous carbonate sediments (C 1 v), and formation of numerous landslide structures. The heating of rocks in the anticline core was accompanied by granitization and dome formation. A small Svetlinsky dome formed in the immediate vicinity of the thrust, creating a thermobaric gradient field (С 2 ). The zone of dome dynamic influence also includes the adjoining thrust area, complicated by a series of sub-vertical thrusts of sub meridional strike and numerous steeply dipping subparallel cracks of the latitudinal strike, synchronously filled with vein quartz and accompanied by hydrothermal metasomatic rock transformations. The formation of the gold deposit occurred during the post-collisional relaxation stage (from P 1 to, probably, the Early Jurassic). The association of gold mineralization with the Svetlinsky dome is indicated by the presence of native gold in Neogene ravine placers in the dome area and marbles of the Svetlinsky deposit, in association with fluorite, F-phlogopite, Cr-muscovite, pink topaz, pure quartz, and native sulphur. The presence of native gold in Neogene ravine placers in the dome area and marbles of the Svetlinsky deposit, in association with fluorite, F-phlogopite, Cr-muscovite, pink topaz, pure quartz, and native sulphur, indicates the association of gold mineralization with the Svetlinsky dome.
-
Date submitted2022-03-22
-
Date accepted2022-06-15
-
Date published2022-07-26
Gold in biogenic apatites of the Baltic-Ladoga phosphorite basin
- Authors:
- Sergey B. Felitsyn
- Nadezhda A. Alfimova
The distribution of gold in biogenic apatites from the Ordovician deposits in the northwest of the East European Platform shows that the maximum concentration of gold in apatites is found within the Ladoga-Baltic suture zone. Gold mineralization has a superimposed character, which is confirmed by the dependence of the gold content on the size of apatite particles and a number of isotope geochemical systematics in biogenic apatites. Gold is present in the form of high fineness particles to 20 µm in size on the surface of biogenic apatite fragments (phosphate brachiopod shells and conodont elements) and is easily extracted. In 10 % of samples of biogenic apatites, the total content of rare earth elements is more than 1 wt.%.
-
Date submitted2020-09-15
-
Date accepted2021-11-30
-
Date published2021-12-27
Evaluating the effectiveness of fine gold extraction technologies on the example of titanomagnetite beach placers of the western coast of Kamchatka
- Authors:
- Valentina E. Kungurova
The material on the gold content of coastal-marine deposits of the western coast of Kamchatka is analyzed and the resource potential is briefly characterized. A review of gold technological estimates obtained from the study of gold-bearing samples taken in promising areas of the coastal-marine strip, from the Bolshaya Vorovskaya River in the north to Cape Levashova in the south, is presented. Stock materials supplemented by our studies were used. Gold-bearing deposits with very fine (0.05-0.1 mm) and fine (0.1-1.0 mm) gold amounting to 94.6 % were tested, as well as samples with gold up to 2 mm and more in addition to fine gold The content of freely recoverable gold reached 91.9 %. In the case of significant gold reserves in placers, prospects for their commercial development open up. experiments on the enrichment of gold-bearing coastal-marine deposits of Western Kamchatka indicate the possibility of extraction of free gold and other valuable components from them. Gravity technologies and modern equipment developed by ОАО Irgiredmet and JSC ITOMAK are the most effective for their extraction. enrichment of gold-bearing formations with simultaneous extraction of several useful components from them, which is possible with the use of fluoride technology, can also become economically advantageous.
-
Date submitted2021-06-24
-
Date accepted2021-11-30
-
Date published2021-12-27
Development of a methodology to assess the hydrocyclone process with account of the rheological properties of the mineral slurry
- Authors:
- Tatiana N. Aleksandrova
- Vadim A. Potemkin
The paper studies the possibility of assessing the separation of mineral raw materials, taking into account the rheology of the mineral slurry. The ores of the Mayskoye deposit were chosen as the object of the study, characterized by a thin impregnation of the valuable component – gold in the host minerals, which determines the use of fine and ultrafine milling. This fact is essential because the presence of a fine grade seriously affects the rheology of the mineral slurry used in subsequent mineral processing stages. This predetermines the necessity to take into account rheological parameters. The research performed provides the development of a methodology for assessing the separation of minerals in the hydrocyclone based on the interpretation of numerical and mathematical modeling data. using the object-oriented programming language Python, a program for calculating empirical coefficients of the rheological equation, theoretically describing the dynamics of internal transformations of the mineral slurry, was developed. Taking into account the process parameters of the laboratory unit with hydrocyclone and ore properties, three concentrations of solids in the mineral slurry were selected, conditionally corresponding to the minimum, average and maximum values. Rheological equations successively composed for three concentrations, i.e., 400, 500, and 700 g/l, made it possible to calculate the critical shear rates corresponding to the maximum dispersion of the mineral slurry in the hydrocyclone flow. Subsequent numerical simulation using Ansys Fluent software, as well as statistical evaluation of the shear rates at different levels of solids content showed that the shear rate profile in the cross-section of the hydrocyclone corresponding to the maximum dispersion of the mineral slurry is obtained at the content of 400 g/l.
-
Date submitted2020-08-20
-
Date accepted2021-11-30
-
Date published2021-12-27
Indicator role of rare and rare-earth elements of the Northwest manganese ore occurrence (South Africa) in the genetic model of supergene manganese deposits
- Authors:
- Aleksandr N. Evdokimov
- Benedict L. Pharoe
The authors analyzed the content of a number of rare and rare-earth elements in the rocks of the Northwest manganese ore occurrence, confined to the Neoarchean dolomites of the Malmani series of the Transvaal Basin. 30 samples of manganese ores and host rocks were analyzed by ICP-MS and XRF methods. Average values of Post-Archean Australian Shale (PAAS) were used as the geochemical standard for data calculation and normalization. The concentrations of elements normalized on PAAS reveal the LREE anomaly in manganese ores. Positive Ce and negative Y–anomalies indicate the hydro-genetical type of sedimentation of ore minerals from manganese-bearing aqueous solutions. This is consistent with the ratios of the elements: Ce and Y SN /Ho SN , Ce and Nd, Fe – Mn – (Co + Ni + Cu) × 10. A clear correlation between the contents of rare-earth elements in manganese nodules and the underlying Malmani dolomites indicates their close genetic relationship. Negative Ce and positive Y–anomalies in manganese wad minerals indicate differences in the conditions of their formation. The manganese wad formed earlier than the rest of the ore with the active participation of microorganisms.
-
Date submitted2021-04-11
-
Date accepted2021-10-18
-
Date published2021-12-16
Comprehensive assessment and analysis of the oil and gas potential of Meso-Cenozoic sediments in the North Caucasus
- Authors:
- Igor I. Bosikov
- Andrey V. Мaier
At the present stage, the development of the oil and gas industry in the Russian Federation is impossible without replenishing the raw material base, so the urgent task is to conduct investigations, prospecting and evaluation of oil and gas bearing capacity prospects in undiscovered areas. The purpose of the investigations is to analyze facies and thicknesses, choose the methodology of prospecting and exploration in reservoirs, make a comprehensive assessment of oil and gas bearing capacity prospects based on experimental investigations and construct a map of oil and gas bearing capacity prospects of the studied sediment structure. The methodology of the conducted investigations was to identify and trace zones of increased fracturing by qualitative interpretation of time seismic sections. Methods for qualitative interpretation of time seismic sections, the model of physical, chemical and geochemical criteria developed by I.A.Burlakov, gas and geochemical surveying and correlation analysis were used in the investigations. A number of prospecting criteria, established based on the analysis of reference seismic materials on well-studied areas in comparison with the results of well tests, were also used. Structural plan for forecast prospects of oil and gas bearing capacity in the studied area was made; zonal and local objects with prospects for oil and gas were identified. Graphical plotting of Eh and pH concentrations distribution and various gas and geochemical indicators allowed identifying zones of possible oil and gas accumulations and starting their detailed survey. Processing of gas and geochemical materials by means of software allowed efficient assessment of prospects for oil and gas bearing capacity of the investigated objects.
-
Date submitted2021-06-24
-
Date accepted2021-10-18
-
Date published2021-12-16
Modeling the acid treatment of a polymictic reservoir
- Authors:
- Mars M. Khasanov
- Andrey А. Maltcev
Acid treatment of wells program is directly related to oil production efficiency. Investigations aimed at improving the efficiency of acid treatment in a terrigenous reservoir have mainly reviewed the changing and adapting the reagents to minimize bridging caused by acid-rock interaction. Under real conditions, application of new and unique acid compositions is a complex process from an organizational point of view and is therefore not widely used as compared with conventional compositions based on a mixture of hydrochloric and hydrofluoric acids. The paper is based on an approach to improve acid treatment efficiency through optimal design based on near-bottomhole zone treatment simulation. The aspects for practical application of the developed acid treatment simulator for terrigenous reservoirs based on a numerical model of hydrodynamic, physical and chemical processes in a porous medium on an unstructured PEBI-grid are described. The basic uncertainties of the model are identified and analyzed. Influence of empirical parameters within the system of equations on the calculation results and modeling of the mineralogical composition of rocks are considered. Algorithm for static modelling of near-bottomhole zone for acid treatment modelling is described, as well as an approach to optimizing the design of near-bottomhole zone treatment based on adapting the results of rock tests in the model. Using experimental data, the necessity of accounting for influence of secondary and tertiary reactions on the results of modeling physical and chemical processes during acid treatment of terrigenous reservoirs was proved. The distinctive features of West Siberian objects (polymictic reservoirs) with respect to the efficiency of near-bottomhole zone treatment with clay acid have been investigated. Series of calculations to determine the optimum volume of acid injection has been carried out. Experience of previously conducted measures under the considered conditions has been analyzed and recommendations to improve the efficiency of acid treatment have been given.
-
Date submitted2020-10-26
-
Date accepted2021-07-28
-
Date published2021-10-21
Investigation of the influence of the geodynamic position of coal-bearing dumps on their endogenous fire hazard
The paper investigates the hypothesis according to which one of the factors influencing the spontaneous combustion of coal-bearing dumps is its geodynamic position, i.e. its location in the geodynamically dangerous zone (GDZ) at the boundary of the Earth crust blocks. This hypothesis is put forward on the basis of scientific ideas about the block structure of the Earth crust and the available statistical data on the location of burning dumps and is studied using computer modeling. A dump located in the area of Eastern Donbass was chosen as the object of research. The simulation results show that the penetration of air into the dump body from the mine through the GDZ, which crosses the mining zone, is possible at an excess pressure of 1000 Pa created by the main ventilation fans. The fire source appearance in the dump body causes an increase in the temperature of the dump mass and becomes a kind of trigger that "turns on" the aerodynamic connection between the dump and the environment, carried out through the GDZ. It is concluded that the establishment of an aerodynamic connection between the mine workings and the dump through the GDZ can be an important factor contributing to the endogenous fire hazard of coal-bearing dumps. The simulation results can be used in the development of projects for monitoring coal-bearing dumps and measures to combat their spontaneous combustion.
-
Date submitted2020-09-09
-
Date accepted2021-03-29
-
Date published2021-09-20
Developing features of the near-bottomhole zones in productive formations at fields with high gas saturation of formation oil
The article studies the formation features of the bottomhole zones in productive formations during operation of production wells in the north of the Perm Territory. Their distinctive feature is the high gas saturation of formation oil. The most widely used parameter in Russian and world practice – the skin factor was used as a criterion characterizing the state of the bottomhole zone. Analysis of scientific publications has shown that one of the main problems of applying the skin factor to assess the state of bottomhole zones is the ambiguity of interpretations of its physical meaning and the impossibility of identifying the prevailing factors that form its value. The paper proposes an approach to identifying such factors in the conditions of the fields under consideration, based on multivariate correlation-regression analysis. Choice of this tool is due to the complexity of the processes occurring in the “formation – bottomhole zone – well” system. When describing complex multifactorial processes, the chosen method demonstrates a high degree of reliability. For a large number of wells in the region, significant material was collected and summarized, including the results of determining the skin factor (1102 values) during hydrodynamic investigations, as well as data on the values of various geological and technological indicators, which can probably be statistically related to the value of the skin factor. A series of multidimensional mathematical models has been built; the skin factor was used as a predicted parameter, and data on the values of geological and technological indicators were used as independent indicators. Analysis of the constructed models is a key stage of this study. Set of parameters included in the multidimensional models, sequence of their inclusion and contribution to the total value of the achieved determination coefficient as the main indicator for the performance of the constructed models were studied. It has been established that the main factor influencing the state of the bottomhole zone is oil degassing. Significant differences in the formation features of the skin factor in the terrigenous and carbonate sediments at the fields under consideration have been determined.