-
Date submitted2024-03-20
-
Date accepted2024-11-07
-
Date published2025-04-25
Analysis of the stress state of rocks transformation near a horizontal well during acid treatment based on numerical simulation
The article presents an overview of the assessment and modelling of the stress state of rocks in the near-wellbore zone of horizontal wells during acid stimulation of the formation for improving the efficiency of oil and gas field development. A numerical finite element model of near-wellbore zone of the reservoir drilled by a horizontal section was compiled using one of oil fields in the Perm Territory as an example. The distribution of physical and mechanical properties of the terrigenous reservoir near the well was determined considering transformation under the action of mud acid for different time periods of its injection. Multivariate numerical simulation was performed and the distribution of horizontal and vertical stresses in near-wellbore zone was determined with regard for different values of pressure drawdown and changes in stress-strain properties depending on the area of mud acid infiltration. It was found that a change in elastic modulus and Poisson's ratio under the influence of acid led to a decrease in stresses in near-wellbore zone. Analysis of the stress distribution field based on the Coulomb – Mohr criterion showed that the minimum safety factor of rock even after the effect of mud acid was 1.5; thus, under the considered conditions of horizontal well modelling, the reservoir rock remained stable, and no zones of rock destruction appeared.
-
Date submitted2023-10-31
-
Date accepted2024-11-07
-
Date published2025-01-24
Specifics of magnetotelluric studies in Antarctica
One of the priority areas of scientific research in Antarctica is the study of its deep structure. Most of the continent is covered with a thick ice sheet, so the main geoscientific data are acquired using geophysical methods, among which magnetotelluric (MT) ones have the greatest penetration depth and insignificant environmental impact. The possibility of acquiring high-quality MT data in the conditions of the sixth continent has long been questioned. The work is aimed at studying the specifics of magnetotelluric survey in Antarctica. The following tasks were set: to summarize the world experience of studying Antarctica using MT sounding methods; to identify factors that negatively affect the high-quality data acquisition; to determine methods for minimizing the influence of these factors. The article analyses geophysical studies conducted by the magnetotelluric sounding method in the Antarctic region from 1964 to the present. The application of the method is complicated by the following: extremely low temperature affects the drop in the batteries capacity, freezing of the non-polarizing electrodes solution, and changes in the strength properties of materials. Electromagnetic noise occurs during strong winds; proximity to the magnetotelluric field source can violate the plane wave principle on which the method is based. The ice sheet covering most of Antarctica does not allow acquiring optimal values of the contact resistance of the electrode grounding; the extended coastline distorts the acquired data. Studies of the influence of factors complicating the MT sounding method in the coastal and central parts of Antarctica made it possible to formulate recommendations for preparing equipment and adapting the work procedure, modifying the processing flow and a set of measures to ensure safety, the implementation of which will both allow safe performance of geophysical investigations and high-quality data acquisition.
-
Date submitted2023-07-04
-
Date accepted2023-09-20
-
Date published2023-10-27
Structure maintenance experience and the need to control the soils thermal regime in permafrost areas
- Authors:
- Anatolii V. Brushkov
- Andrei G. Alekseev
- Svetlana V. Badina
- Dmitrii S. Drozdov
- Vladimir A. Dubrovin
- Oleg V. Zhdaneev
- Mikhail N. Zheleznyak
- Vladimir P. Melnikov
- Sergei N. Okunev
- Aleksei B. Osokin
- Nikolai A. Ostarkov
- Marat R. Sadurtinov
- Dmitrii O. Sergeev
- Roman Yu. Fedorov
- Konstantin N. Frolov
The risks of reducing the stability of buildings and structures are increasing in conditions of climate change and the active development of the territories under the influence of natural and anthropogenic factors. The main causes include: loss of the bearing capacity of frozen soils, various geocryological processes, errors at the stages of design, construction and operation of facilities. Main actual task when conducting research and industrial operations in the cryolithozone is monitoring and, if necessary, managing thermal processes in the permafrost layers interacting with facilities. In this article the obtained positive experience of various technologies applying at various stages of the life cycle of civil and industrial facilities was analyzed. It helps to eliminate or prevent the structure deformation or destruction under the influence of climate change. The methods of permafrost stabilization used in the oil and gas industry in process of industrial infrastructure development of the fields have been studied – freezing (cooling) of foundation soils during construction on heterogeneous foundations. The solution to the problems of minimizing accidents when locating production wells in the permafrost zone of the Yamal Peninsula is considered using the example of an oil and gas condensate field and restoring of the temperature regime of perennial unfrozen soils in areas of valve units of main gas pipelines. An assessment of methods used to maintain the industrial and residential infrastructure within the northern municipalities that ensure the functioning of the fuel and energy complex of the Russian Federation in the Arctic was made. The systems of thermal stabilization in the foundations of buildings and industrial facilities built and operated on permafrost soils allow to fully use the high strength and low deformability of frozen grounds. It ensures the state's long-term plans of the industrial development in the Arctic.
-
Date submitted2023-04-29
-
Date accepted2023-10-11
-
Date published2023-10-27
Pink-violet diamonds from the Lomonosov mine: morphology, spectroscopy, nature of colour
The article presents the results of the first comprehensive study of mineralogical and spectroscopic (IR, PL, EPR) characteristics of diamonds from the Lomonosov mine (Arkhangelskaya pipe) with a unique pink, pink-violet colour. It is shown that all crystals belong to the IaA type, with a total nitrogen content in the range of 500-1500 ppm, with a low degree of aggregation. The colour is heterogeneous, concentrated in narrow twin layers. It is presumably caused by the previously described M2 centres. The colour shade is affected by the content of P1 paramagnetic centres (C-defect). A positive correlation is observed between the colour saturation and the intensity of W7 paramagnetic centres. A convergent model of the formation of pink diamonds is assumed, according to which the determining factors are the ratio and concentration of structural impurities in the diamond, its thermal history, and conditions of plastic deformation, and not the origin of the diamond and the petrochemical properties of its host rocks.
-
Date submitted2022-06-27
-
Date accepted2023-06-20
-
Date published2023-12-25
Analysis of the problems of high-quality drinking water extraction from underground water intakes on Vysotsky Island in the Vyborg district of the Leningrad region
This article presents the results of drilling, experimental filtration work and laboratory studies aimed at assessing the resources and quality of groundwater in the licensed area of Vysotsky Island located in the Leningrad region, in the Gulf of Finland in accordance with the requirements of regulatory documents. Analysis of the results of hydrochemical studies and their comparison with data on water intakes in adjacent areas gives the right to conclude that it is possible to classify a hydrogeological unit as a different type of resource formation than those located in the surrounding areas. Groundwater in this area is confined to an unexplored deep fractured regional high-pressure zone. According to the received data, the explored water intake can be attributed to a unique groundwater deposit, which has an uncharacteristic composition of groundwater in the north of the Leningrad region, which may be due to the mixing of modern sediments and relict waters of the Baltic glacial lake. The stability of groundwater characteristics is confirmed by long-term monitoring.
-
Date submitted2022-10-29
-
Date accepted2023-02-13
-
Date published2023-04-25
The use of unmanned aerial photography for interpreting the technogenic transformation of the natural environment during the oilfield operation
The traditional approach to monitoring observations of the technogenic processes development in oilfields, which consists in determining the concentration of marker pollutants in various natural environments, does not provide the necessary completeness of information and the efficiency of its receipt. The paper considers an example of expanding the range of observations due to unmanned aerial photography and a number of other methods. Interpretation signs (for panchromatic survey) were determined that register such consequences of technogenic transformation of the natural environment as mechanogenesis, bitumization, and halogenesis. Technogenic mechanogenesis is understood as a physical violation of the integrity of ecosystems, the movement of soils and grounds. Bitumization is expressed in the migration of petroleum hydrocarbons through soils, ground, surface, subsurface, and underground waters, and their destruction. Salt migration in these media is defined as halogenesis. The most reliable indicators are linearly elongated areas of dead forests, dark red spots in drying microdepressions and reservoirs. It was found out that the oilfield impact on the raised bog leads to anthropogenic eutrophication, the introduction of plant species, uncharacteristic coenotic groups, the replacement of subshrubs with grasses, and morphometric changes in forest pine. In the peat deposits of the disturbed area, an unusual interlayer of whitish, undecomposed moss was recorded. The moment of the beginning of a pronounced technogenic transformation was registered in the course of work with the archive of multispectral space images. Continuous remote sensing with the help of unmanned aerial photography and interpretation by sedimentological, geobotanical methods significantly expand the possibilities of studying the technogenic transformation of the natural environment. To ensure environmental safety, it is advisable to develop remote methods and technologies to include them in the environmental monitoring system.
-
Date submitted2021-05-27
-
Date accepted2022-09-06
-
Date published2022-11-10
Application of resonance functions in estimating the parameters of interwell zones
It is shown that the use of force resonance leads to the effect of “shaking” the formation, followed by breaking up the film oil and involving it in the further filtration process. For the first time in oilfield geophysics, the concept of passive noise-metering method is justified for monitoring oil and gas deposit development by measuring the quality factor of the contours in the point areas of formation development channels in interwell zones. It is established that determining the depth of modulation for the reactive substitution parameter of the linear FDC chain is crucial not only for determining the parametric excitation in FDC attenuation systems, but also without attenuation in the metrological support for the analysis of petrophysical properties of rock samples from the wells. It is shown that based on the method of complex amplitudes (for formation pressure current, differential flow rates, impedance), different families of resonance curves can be plotted: displacement amplitudes (for differential flow rates on the piezocapacity of the studied formation section), velocities (amplitudes of formation pressure current) and accelerations (amplitudes of differential flow rates on the linear piezoinductivity of the FDC section). The use of predicted permeability and porosity properties of the reservoir with its continuous regulation leads to increased accuracy of isolation in each subsequent sub-cycle of new segment formation in the FDC trajectories, which contributes to a more complete development of productive hydrocarbon deposits and increases the reliability of prediction for development indicators.
-
Date submitted2022-04-29
-
Date accepted2022-07-21
-
Date published2022-11-10
Deep structure, tectonics and geodynamics of the Sea of Okhotsk region and structures of its folded frame
The use of the zonal-block model of the earth's crust for the construction of regional tectonic schemes and sections of the earth's crust based on a complex of geological and geophysical data makes it possible to consider the resulting maps and sections as tectonic models. The main elements of such models are blocks with an ancient continental base and interblock zones formed by complexes of island arcs, an accretionary prism, or oceanic crust. The developed geotectonic model of the Sea of Okhotsk region reflects the features of the deep structure, tectonics, and geodynamics. The Cimmerian Novosibirsk-Chukotka, Verkhoyansk-Kolyma, Kolyma-Omolon, and Amur folded regions and the Alpides of the Koryak-Kamchatka and Sakhalin-Sikhote-Alin folded regions are developed along the northern, western, and southern boundaries of the Sea of Okhotsk megablock with a continental crust type. From the east, the megablock is limited by oceanic basins and island arcs.
-
Date submitted2022-04-04
-
Date accepted2022-05-13
-
Date published2022-07-13
Distribution of trace elements controlled by sector and growth zonings in zircon from a miaskite pegmatite of the Vishnegorsky massif, the Southern Urals
Data on the content and distribution of trace and rare-earth elements (SIMS method) in sectors and growth zones of a large zircon crystal from miaskite pegmatites of the Vishnegogorsky massif are presented. The morphology of the zircon crystal is a combination of a dipyramid {111} and prism {010}. It has been established that the growth sector of dipyramid {111} is characterized by almost one order of magnitude higher contents of Y, Nb, REE, Th; higher Th/U and Eu/Eu* values; REE distribution spectra are flatter compared to prism {010} growth sector. A regular decrease in the content of trace and rare-earth elements in the direction from the central zone to the marginal zone of crystal growth was revealed. A smooth regression of zircon crystallization temperature of zircon from 960 °C in the central zone to 740 °C in the marginal zone of the dipyramid sector and 700-650 °C in the prism sector has been revealed, which may be a reflection of thermal evolution of the crystallization process. It is assumed that crystallization of the central zone of zircon occurred at early stages from a relatively trace-еlement-rich melt. The crystallization was completed at lower temperatures, probably, simultaneously with the formation of REE-concentrating minerals, which resulted in natural decrease of content of trace and rare-earth elements in the melt and, consequently, in zircon crystallizing from it.
-
Date submitted2021-04-19
-
Date accepted2021-10-18
-
Date published2021-12-16
Mutual spectral densities calculation of the moments of resistance on the peat milling unit working bodies
- Authors:
- Konstantin V. Fomin
When performing technological operations in the peat industry, various units with milling-type working bodies are used. They differ in design, layout, number and type of cutting elements, operating modes, and may have one or more working bodies. During operation, random forces and moments act on the cutters, which have a dramatically variable nature, which is associated with the periodic interaction of the knives with the peat deposit, its structural heterogeneity, variations in the milling depth, physical and mechanical properties of peat, the rotational speed of the cutter and the movement speed of the machine. In this case, significant dynamic loads arise in the structural elements, which leads to a decrease in their reliability, deterioration of the energy characteristics of the engine operation and technical and economic indicators of use. In the dynamic analysis of drive elements, when using machines with several working bodies, it is necessary to know both spectral and mutual spectral load densities. For their calculation, expressions were obtained that take into account the physical and mechanical properties of peat, the operating modes of the unit and their probabilistic characteristics, as well as the design features of the working body. The expressions are obtained for the case when there are several working bodies with the same diameters and the number of knives in the cutting plane. In this case, the number of planes, width, type of cutting element and type of cutting (locked, semi-locked, etc.) may differ. As an example of using the developed approaches, the calculation of spectral and mutual spectral densities of moments on cutters and loads in the drive elements of the machine for surface-layer milling MTF-14 is presented.
-
Date submitted2020-10-26
-
Date accepted2021-07-28
-
Date published2021-10-21
Investigation of the influence of the geodynamic position of coal-bearing dumps on their endogenous fire hazard
The paper investigates the hypothesis according to which one of the factors influencing the spontaneous combustion of coal-bearing dumps is its geodynamic position, i.e. its location in the geodynamically dangerous zone (GDZ) at the boundary of the Earth crust blocks. This hypothesis is put forward on the basis of scientific ideas about the block structure of the Earth crust and the available statistical data on the location of burning dumps and is studied using computer modeling. A dump located in the area of Eastern Donbass was chosen as the object of research. The simulation results show that the penetration of air into the dump body from the mine through the GDZ, which crosses the mining zone, is possible at an excess pressure of 1000 Pa created by the main ventilation fans. The fire source appearance in the dump body causes an increase in the temperature of the dump mass and becomes a kind of trigger that "turns on" the aerodynamic connection between the dump and the environment, carried out through the GDZ. It is concluded that the establishment of an aerodynamic connection between the mine workings and the dump through the GDZ can be an important factor contributing to the endogenous fire hazard of coal-bearing dumps. The simulation results can be used in the development of projects for monitoring coal-bearing dumps and measures to combat their spontaneous combustion.
-
Date submitted2020-09-09
-
Date accepted2021-03-29
-
Date published2021-09-20
Developing features of the near-bottomhole zones in productive formations at fields with high gas saturation of formation oil
The article studies the formation features of the bottomhole zones in productive formations during operation of production wells in the north of the Perm Territory. Their distinctive feature is the high gas saturation of formation oil. The most widely used parameter in Russian and world practice – the skin factor was used as a criterion characterizing the state of the bottomhole zone. Analysis of scientific publications has shown that one of the main problems of applying the skin factor to assess the state of bottomhole zones is the ambiguity of interpretations of its physical meaning and the impossibility of identifying the prevailing factors that form its value. The paper proposes an approach to identifying such factors in the conditions of the fields under consideration, based on multivariate correlation-regression analysis. Choice of this tool is due to the complexity of the processes occurring in the “formation – bottomhole zone – well” system. When describing complex multifactorial processes, the chosen method demonstrates a high degree of reliability. For a large number of wells in the region, significant material was collected and summarized, including the results of determining the skin factor (1102 values) during hydrodynamic investigations, as well as data on the values of various geological and technological indicators, which can probably be statistically related to the value of the skin factor. A series of multidimensional mathematical models has been built; the skin factor was used as a predicted parameter, and data on the values of geological and technological indicators were used as independent indicators. Analysis of the constructed models is a key stage of this study. Set of parameters included in the multidimensional models, sequence of their inclusion and contribution to the total value of the achieved determination coefficient as the main indicator for the performance of the constructed models were studied. It has been established that the main factor influencing the state of the bottomhole zone is oil degassing. Significant differences in the formation features of the skin factor in the terrigenous and carbonate sediments at the fields under consideration have been determined.
-
Date submitted2021-01-28
-
Date accepted2021-04-21
-
Date published2021-06-24
Unusual metasomatites (phyolithites) in the Kolvitskiy gabbro-anorthosite rock mass: composition and structural position
Complex mineralogical, geochemical, and geological-structural characteristics of a rare collection stone of violet color, phyolithite, in the southwestern part of the Kola Peninsula. This is a metasomatic rock formed under the conditions of brittle deformations on gabbro-anorthosites of the Paleoproterozoic Kolvitskiy rock mass. As a result of potassium metasomatosis, the plagioclase of the initial rocks was replaced by a fine-grained mica aggregate of muscovite-phengite composition with inclusions of Va-aluminoseladonite (up to 20-30 microns). Ba-aluminoseladonite contains 6.6-10.5 % by weight of BaO. Manganese is the only chromophore that accumulates in the rock during metasomatosis. It is manganese that provides the purple-violet color of pseudomorphs of mica according to anorthite. The phyolithites is depleted by REE and has a positive Eu-anomaly. The phyolithites are confined to the areas of fracturing of the north-eastern strike, located in the zone of dynamic influence of the north-western closure of the Onega-Kandalaksha rift of the Riphean age. Other formations (injection conglomerates and lamproites) are also associated with the formation of this structure, which owe their origin to an intense fluid flow.
-
Date submitted2020-08-20
-
Date accepted2021-04-01
-
Date published2021-06-24
Features of the mineral and chemical composition of the Northwest manganese ore occurrence in the Highveld region, South Africa
- Authors:
- Aleksandr N. Evdokimov
- Benedict L. Pharoe
The Northwest manganese ore mineralisation is located at a relative distance from traditionally known manganese mining areas in a new manganese-bearing region (Highveld) in the Northwest Province, Republic of South Africa. The ore occurrence was studied on farms: Buchansvale 61 IQ, Weltevreden 517 JQ, Rhenosterhoek 343 JP and Kafferskraal 306 JP. The data obtained from studying the geology of the area pointed out to interests regarding the development criterias for search of similar ore mineralisations in the northwest region of South Africa. The ore occurs predominantly in the form of powdered manganese wad, manganese nodules and crusts, confined to the karstic structures of the upper section of the dolomites. X-ray powder diffraction (XRD), Scanning electron microscopy with energy dispersive link (SEM-EDS) and X-ray fluorescence were utilized to unveil the mineral and chemical composition of the ore samples. The present study therefore presents the results on both chemical and mineral composition of manganese ores, and their depth and longitudinal distribution. Karstic areas causing an increased local thickness of the ore body were identified. The geochemical and microspcopic study of the ores indicates their supergene nature. The main ore minerals includes cryptomelane, lithiophorite, purolusite, hollandite and romanechite associated with impurity components of Ba, Ce, Co, La, Cr, Zn and V.
-
Date submitted2020-11-11
-
Date accepted2021-03-02
-
Date published2021-04-26
Oil and gas content of the understudied part in the northwest of the Timan-Pechora oil and gas province according to the results of basin modeling
Comprehensive interpretation of the results for regional seismic operations and reinterpretation of archived seismic data, their correlation with the drilling data of more than 30 deep wells, including Severo-Novoborsk parametric well, made it possible to clarify the structural maps and thickness maps of all seismic facies structures developed in the territory and water area in the junction of the north of Izhma-Pechora depression and Malozemelsko-Kolguevsk monocline of Timan-Pechora oil and gas province. Data obtained were used at basin modeling in TemisFlow software in order to reconstruct the conditions of submersion and transformation of organic substance in potential oil and gas bearing formations. Modeling made it possible to get an idea of the time and conditions for the formation of large zones of possible hydrocarbons accumulation, to establish space-time connections with possible sources of generation, to identify the directions of migration and on the basis of comparison with periods of intense generation, both from directly located within the operation area and outside them (taking into account possible migration), to identify zones of paleoaccumulation of oil and gas. Work performed made it possible to outline promising oil and gas accumulation zones and identify target objects for further exploration within the site with an ambiguous forecast and lack of industrial oil and gas potential.
-
Date submitted2019-09-25
-
Date accepted2019-12-20
-
Date published2020-04-24
Study of the well near-bottomhole zone permeability during treatment by process fluids
- Authors:
- Evgenii A. Rogov
In the process of drilling-in productive horizons, several irreversible physical and chemical processes take place in the near-wellbore zone of the formation: stress state of the rocks changes, penetration of the filtrate and solid phase, as well as drilling mud into the reservoir, and swelling of clay particles of intergranular cementing material are observed. As a result, permeability of productive horizon is significantly reduced and, consequently, potential inflow of oil or gas from formation is excluded. An equally serious problem exists during well servicing and workover, when the use of irrational fluids of well killing causes negative consequences associated with deterioration of reservoir properties of formations in the wells being repaired. Article presents the results of the experiments on permeability of clayed porous samples after exposure to various compositions of liquids. In order to increase permeability of near-borehole zone of the formation and increase productivity of wells completed by drilling, and after well servicing and workover, a composition of the process fluid containing a 15 % aqueous solution of oxyethylene diphosphonic acid (OEDA) with addition of a surfactant is proposed.
-
Date submitted2019-06-19
-
Date accepted2019-09-11
-
Date published2020-02-25
Method for estimating the spectrum density of the resistance moment on the working body of a peat milling unit
- Authors:
- K. V. Fomin
The main source of dynamic loads in the drive elements and the design of the peat milling unit is the working body. The forces of external resistance arising in the process of performing a technological operation are sharply variable, random in nature. The article proposes a model of formation of the moment of resistance on the mill when interacting with peat. The case when there are several cutting planes with the same radius at the ends of the cutting elements is considered. When developing the model, it was taken into account that the operating conditions of the knives, determined by the type of cutting (blocked, semi-blocked, etc.), their width and type in each cutting plane can vary. Factors that determine the nature of loading, such as the frequency of interaction of the cutting elements with the fallow and the randomness of the operating conditions of the unit, lead to the presentation of the loads in the form of a sequence of pulses with random parameters. Expressions are obtained for determining the spectral density of the moment of resistance on the mill at the design stage, taking into account its design, operating modes, physico-mechanical properties of peat and their probabilistic characteristics. To illustrate the application of the developed approaches, a technique is presented for determining the spectral density of the moment on the working body of deep milling machines and in their drive elements based on a linear model. An example of calculation is given, and the obtained expressions are verified on the basis of experimental data. The probabilistic characteristics of the loads on the mill serve as initial information for the dynamic analysis of the drive system and the design of the unit, its strength analysis, the selection of optimal parameters and operating modes.
-
Date submitted2019-07-17
-
Date accepted2019-09-04
-
Date published2019-12-24
On flood protection measures for potash mines
- Authors:
- A. A. Baryakh
- E. A. Gubanova
Development of water-soluble ore deposits is associated with the necessity to preserve water blocking strata (WBS), which separate aquifers from the mine gob. One indicator of the rate of man-induced load on WBS layers is subsidence of the earth surface, which defines the character of shift trough formation of the earth surface. The greatest threat of WBS discontinuity is posed by the areas located at the edges of a shift trough. From the perspective of Upper Kama deposit of potassium and magnesium salts, by means of mathematical modelling methods authors demonstrated that in the capacity of threat indicators of WBS hole destruction it is possible to use the following parameters of a shift trough: edge length scaled to the depth of mining operations and maximum subsidence of the earth surface. Critical combination of these factors is responsible for the discontinuity at the edges of water blocking strata. These parameters of a shift trough can easily be controlled by instrumental procedures and can be included in the basics of a general monitoring system of WBS state at potash mines. In order to protect the mine from the inrush of fresh water, it is necessary to form softening zones at the edges of mined-out areas near permanent or temporary borders of mining operations. Authors review different options of softening zone formation. Numerical tests have demonstrated that the most efficient way to protect water blocking strata is the formation of softening zones by means of backfilling the stopes of the workable seam or its exclusion from mining operations.
-
Date submitted2019-02-26
-
Date accepted2019-05-22
-
Date published2019-08-23
Systemic Diagnostics of the Arctic Industry Development Strategy
The article analyzes organizational and economic problems of the industry in the Arctic and discloses methods and tools for researching these problems. An attempt to use the method of system diagnostics is made, which has established itself as a basis for determining the development strategy of industry in the Arctic zone of the Russian Federation (AZRF). This method allows to explore the mechanism of natural resources development in the Arctic, such as hydrocarbons and marine biological resources; as well as the organization of logistics and transport corridors for trade of goods produced in the North and in the central regions of Russia. The role, significance and content of the strategy as an essential element of the system for managing natural wealth development in the Arctic in the context of its growing importance in development of global transport corridor are revealed. Importance of a systematic approach to the development of industry in the Arctic is substantiated, it will ensure development of all investors interested in this region; will allow the state, large corporations, small and medium-sized businesses to work together for the long term. The proposed method for system diagnostics of strategizing the development of industrial potential in the AZRF can be used in the implementation of «Development Strategy for the Arctic Region» as part of roadmap realization for the Arctic region.
-
Date submitted2019-03-13
-
Date accepted2019-05-07
-
Date published2019-08-23
Modern Mathematical Forecast Methods of Maintenance and Support Conditions for Mining Tunnel
- Authors:
- S. A. Ignatyev
- A. E. Sudarikov
- A. Zh. Imashev
The research focuses on mathematical methods of mining pressure forecast to develop rational support patterns for mining tunnels and to ensure safety of mining operations. The purpose of research is to develop the methodology of applying advanced calculation methods and software solutions based on neural networks to reduce dispersion of factors influencing stability of mining tunnels, as well as to define rational parameters of mining tunnel support. The authors review the algorithm of geomechanical process examination, which is divided into several stages. First of all, it is proposed to use cluster analysis to examine location conditions of man-made outcrops, which allows to divide all the diversity of existing conditions for mining tunnel construction. Cluster analysis first allows to reduce the dispersion of factors that influence the stability of mining tunnels in various clusters, and then to determine rational parameters of tunnel support in each cluster. After the problem of cluster analysis is solved, it is proposed to use software programs that allow to study geomechanical processes in each cluster. At this stage, both standard methods (normative techniques, numerical modelling, analogies use, etc.) and the most advanced methods – neural networks – can be applied. Described algorithm of solving geomechanical problems, which utilizes advanced numerical methods and a software package based on neural networks, ensures an individual approach to estimation of mining pressure under varying conditions of man-made outcrop location in the rock mass.
-
Date submitted2018-11-20
-
Date accepted2018-12-28
-
Date published2019-04-23
Refined assessment of seismic microzonation with a priori data optimisation
- Authors:
- I. B. Movchan
- A. A. Yakovleva
The work is devoted to the issues of seismic microzonation representativeness, which is amongst the mandatory assessments that precedes civil and industrial construction. In addition to the practical approach and in accordance with the normative documentation, the authors propose parametric interpretation of the remote basis by means of tracing geodynamic zones and elements of the geoblock structure, where the leading marker of seismogenic risk zones is the anomaly of spatial variability of the geofield, coinciding with the discordant intersection of localised land structures. Verification of this marker is achieved by displaying a cartographic distribution image within the range of the seismic point increment, detailed on the basis of approximation dependencies.
-
Date submitted2018-05-09
-
Date accepted2018-06-30
-
Date published2018-10-24
Scientific and methodical approaches to increase prospecting efficiency of the russian arctic shelf state geological mapping
- Authors:
- A. S. Egorov
- I. Yu. Vinokurov
- A. N. Telegin
A rationale for the set of theoretical and methodological techniques of mapping and deep modeling in the Russian Arctic shelf and adjacent sedimentary basins in continental Russia is based on the materials for the Barents and Kara Seas region. This article provides the factual basis of the research and shows how to apply zonal-block model of the crust and generalized models of geodynamic settings in terms of the different geophysical data inconsistency. The necessity and approach for global and regional paleo-reconstructions are also discussed. It is shown that localization of the principal structural and compositional units of the lithosphere being a consequence of geodynamic processes at the boundaries of lithospheric plates, form at the basis of sedimentary cover and crystalline basement layered maps as well as cross-sections of the continental crust. The identified parameters of the deep structure and milestones of the regional tectonic history open new opportunities to explore the regularities of ore deposits distribution. The shown example of the forecast and metallogeny problems solution within Western Siberia and Khatanga-Vilyui petroleum provinces is made using the parameters of known industrial oil and gas fields for training the pattern recognition system.
-
Date submitted2018-01-17
-
Date accepted2018-03-09
-
Date published2018-06-22
Control and regulation of the hydrochloric acid treatment of the bottomhole zone based on field-geological data
- Authors:
- M. K. Rogachev
- V. V. Mukhametshin
The analysis results of the hydrochloric acid treatment of the bottomhole zone efficiency along the deposits of high-viscosity oil in the carbonate reservoirs of the Tournaisian stage are presented in the paper. Based on the use of the non-parametric Kulbak criterion, the most informative geological and technological parameters, which affect most the success of hydrochloric acid treatments, assessed by the criteria of increased oil production and reduced water cut, are revealed. The generalization of the hydrochloric acid treatments experience in the conditions of the high-viscosity oil reservoirs of the Tournaisian Stage allows for efficient forecasting, selection of wells, control and regulation of the treatment process to reduce the number of inefficient operations and improve the technical and economic parameters of fuel and energy enterprises at the investigated sites and the ones with similar field-geological characteristics.
-
Date submitted2017-11-09
-
Date accepted2018-01-02
-
Date published2018-04-24
Analyis of government support tools for mining companies in the Russian Arctic zone
The paper focuses on the development of mining companies in the Russian Arctic zone in the context of searching for new ways to improve government control over the development of the Arctic zone. Existing outer restrictions imposed upon Russia and changes in the global financial market not only determined a paradigm shift to regional government control, but also dictated the need to search for new mechanisms of state influence on the regional economy. Primarily it concerns the development of growth zones based on utilizing resource potential, creation and implementation of tools aimed at attracting investments to the Arctic zone and offsetting the factors of northern appreciation for mining companies. With this in mind, government support of specific regional development projects is becoming an urgent issue. The authors analyze new approaches to the development of public management in the Russian Arctic zone, for mining companies in particular, aimed at creating special economic conditions that would stimulate the operation of plants extracting mineral resources. Research methodology is based upon the analysis of factors restricting economic development and growth of the Russian Arctic zone and mining companies in the first place, as well as analysis of possible tools to support mining plants operating in the Arctic territories (advanced development zones, industrial clusters, «supporting zones»). The authors define priority goals and prospects of implementing such operation mode for mining companies in the Arctic zone, and propose a list of possible measures of government support needed to stimulate development of mining companies and the entire Arctic economy of Russia.
-
Date submitted2017-11-08
-
Date accepted2018-01-20
-
Date published2018-04-24
Major trends in efficiency upgrading of the economic activity in the Arctic zone of Russian Federation
Organization of efficient economic activity in the Arctic zone requires development of human potential, transport infrastructure, exploitation of natural resources under the conditions of greatest possible environmental safety. In order to choose preferable trends of economic development and to provide efficiency of operations in the Arctic zone it is crucial to perform research in the areas of industrial efficiency upgrading and rational use of fuel, energy, mineral, chemical and biological resources of the Ocean and littoral areas of Russian Arctic. The paper analyzes major trends in the research on increasing economic efficiency of operations aimed at territory development in the Arctic zone. The authors justify the need to examine economic problems of rational resource use in the Arctic zone of Russia based on the proposed system of resource-estimation indicators and their application in establishing a mechanism of rational resource use with a due regard to protection of the marine environment. The paper also focuses on methodological problems of the target programme approach to complex development of the Arctic zone, creation of target programmes, industrial development and rational use of natural resources. The authors give rationale for the key task in this area – development of methodological principles of forming federal and regional target programmes, aimed at exploration, exploitation and rational use of natural resources in the Arctic zone of Russian Federation. An analysis is provided that focuses on the problems of creating a scientifically justified hierarchical system of programmes and regional regulations, creation of a scientific information data bank and other methodological issues.