-
Date submitted2023-09-29
-
Date accepted2023-10-25
-
Date published2024-08-26
Laboratory studies of transformation of porosity and permeability and chemical composition of terrigenous reservoir rocks at exposure to hydrogen (using the example of the Bobrikovskii formations in the oil field in the northeast Volga-Ural oil and gas province)
The article describes the methodology for laboratory studies of reservoir rock exposure to hydrogen. The stages of sample research and the instruments used in the experiments are considered. A comparative analysis of the results of studies on porosity and permeability of core samples was performed. It was shown that after exposure to hydrogen, the porosity decreased by 4.6 %, and the permeability by 7.9 %. The analysis of correlation dependencies demonstrated a typical change in the relationship of these characteristics: after the samples exposure to hydrogen the scatter of the values increased and the correlation coefficient decreased, which indicates a change in the structure of the void space. Based on the research results, it was concluded that the decrease in porosity and permeability of the core samples occurred due to their minor compaction under the action of effective stresses. The chemical analysis of the rock showed no major difference in the composition of the basic oxides before and after exposure to hydrogen, which points to the chemical resistance of the studied formation to hydrogen. The experimental results showed that the horizon under consideration can be a storage of the hydrogen-methane mixture.
-
Date submitted2022-05-20
-
Date accepted2023-04-03
-
Date published2024-02-29
Impact of carbon dioxide on the main geotechnical quality criteria and preparation cost of cemented paste backfill
There is a global upsurge in the use of cemented paste backfill (CPB) for various mining functions. However, the cost of the Portland cement binder is prohibitive, thus warranting strategies to reduce cement usage without overly diminishing the CPB quality. Since carbon dioxide is used for patented sand moulding processes, this study is premised on that physicochemical ability of CO2 to enhance the curing of consolidated inorganic materials. It evaluated the impact of carbon dioxide on the uniaxial compressive strength UCS and preparation cost of CPB standard samples (ASTM C109). The preparation cost was delimited to the purchase cost of the Portland cement. The backfill material was silica sand tailings with 4.5 wt.% Portland cement binder and a water-cement ratio of 7.6. Distilled water of pH 5.4 was used for the control samples while variable amounts of carbon dioxide were dissolved in distilled water to generate carbonated mixing water with pH values of 3.8; 4 and 4.2. The lower the carbonated water pH, the higher is the CO2 concentration. UCS tests were conducted on the samples after curing for 3, 7, 28, and 90 days. There was an observable increase in the UCSs and reduction in curing time with increasing carbon dioxide. Samples prepared with carbonated water of pH 3.8 had almost double the strength of those prepared with pure distilled water of pH 5.4, implying that more dissolved CO2 corresponds to higher CPB strength. This is supported by the trendline equations for the graphical simulation of strength on curing time. Thus, CPB with much less binder can be expected to attain the requisite UCS if carbon dioxide is incorporated. The average reduction in Portland cement consumption was 0.61 %, which translates to a cost saving of the same percentage points. If calculated over the operational life of a mine, this is a massive saving of millions of dollars.
-
Date submitted2022-04-07
-
Date accepted2023-04-21
-
Date published2023-08-28
Development of a new assessment system for the applicability of digital projects in the oil and gas sector
Digital transformation is one of the global trends that has covered most sectors of the economy and industry. For oil and gas companies, the introduction of digital technologies has become not just a trend, but one of the factors for ensuring competitiveness and maintaining a stable position in the market in a rapidly changing macro environment. At the same time, despite the positive effects achieved, digital transformation is a complex process from the point of view of implementation and is associated with high technological, financial, and economic risks. The work aims to develop and test a new system for evaluating the applicability of digital projects in the oil and gas sector. The research methodology includes the application of the Gartner curve, methods of expert assessments, and tools for assessing the economic efficiency of investment projects. The developed assessment system is based on a comprehensive accounting of four components: the level of digital maturity of the company; compliance of the implemented technology with the goals and objectives of the organization; the level of reliability of the implemented technology; the level of innovation of the implemented project. Particular attention is paid to the practical testing of the proposed methodology based on the evaluation of a digital project implemented by a Russian oil and gas company.
-
Date submitted2021-07-05
-
Date accepted2022-11-17
-
Date published2022-12-29
Determination of suitable distance between methane drainage stations in Tabas mechanized coal mine (Iran) based on theoretical calculations and field investigation
A large amount of gas is emitted during underground mining processes, so mining productivity decreases and safety risks increase. Efficient methane drainage from the coal seam and surrounding rocks in underground mines not only improves safety but also leads to higher productivity. Methane drainage must be performed when the ventilation air cannot dilute the methane emissions in the mine to a level below the allowed limits. The cross-measure borehole method is one of the methane drainage methods that involves drilling boreholes from the tailgate roadway to an un-stressed zone in the roof or floor stratum of a mined seam. This is the main method used in Tabas coal mine N 1. One of the effective parameters in this method is the distance between methane drainage stations, which has a direct effect on the length of boreholes required for drainage. This study was based on the measurement of ventilation air methane by methane sensors and anemometers placed at the longwall panel as well as measuring the amount of methane drainage. Moreover, in this study, the obtained and analyzed data were used to determine the suitable distance between methane drainage stations based on the cross-measure borehole method. In a field test, three borehole arrangements with different station distances in Panel E4 of Tabas coal mine N 1 were investigated. Then, the amounts of gas drained from these arrangements were compared with each other. The highest methane drainage efficiency was achieved for distances in the range of 9-12 m between methane drainage stations.
-
Date submitted2021-04-26
-
Date accepted2021-07-27
-
Date published2021-10-21
Study of the dynamics for gas accumulation in the annulus of production wells
Accumulation of associated petroleum gas in the annulus is one of the negative factors that impede the intensification of mechanized oil production. An increase in annular gas pressure causes growth of bottomhole pressure, a decrease in back pressure to the formation and the inflow of formation fluid. In addition, accumulation of gas in the annulus leads to displacement and a decrease in the liquid level above the submersible pump. Insufficient level of the pump submersion (rod or electric submersible) causes a number of complications in the operation of mechanized production units associated with overheating of the elements in pumping units. Therefore, the development of technologies for optimizing the gas pressure in the annulus is relevant. Method for calculating the intensity of gas pressure increase in the annulus of production wells operated by submersible pumps has been developed. Analytical dependence for calculating the time interval of gas accumulation in the annulus, during which the dynamic level decreases to the pump intake, is obtained. This value can be used to estimate the frequency of gas withdrawal from the annulus using compressors. It has been found that the rate of increase in annular gas pressure in time increases non-linearly with a rise in the gas-oil ratio and a decrease in water cut, and also linearly increases with a rise in liquid flow rate. Influence of the operating (gas-oil ratio) and technological (value of the gas pressure maintained in the annulus) factors on the flow rate of the suspended reciprocating compressor driven by the beam engine, designed for forced withdrawal and redirection of the annular gas into the flow line of the well is analyzed.
-
Date submitted2021-04-15
-
Date accepted2021-07-27
-
Date published2021-10-21
Analysis of the application and impact of carbon dioxide media on the corrosion state of oil and gas facilities
Products of several currently operated production facilities (Bovanenkovskoye, Urengoyskoye oil and gas condensate fields, etc.) contain an increased amount of corrosive CO 2 . Effect of CO 2 on the corrosion of steel infrastructure facilities is determined by the conditions of its use. Carbon dioxide has a potentially wide range of applications at oil and gas facilities for solving technological problems (during production, transportation, storage, etc.). Each of the aggregate states of CO 2 (gas, liquid and supercritical) is used and affects the corrosion state of oil and gas facilities. Article analyzes the results of simulation tests and evaluates the corrosion effect of CO 2 on typical steels (carbon, low-alloy and alloyed) used at field facilities. The main factors influencing the intensity of carbonic acid corrosion processes in the main conditions of hydrocarbon production with CO 2 , storage and its use for various technological purposes are revealed. Development of carbon dioxide corrosion is accompanied and characterized by the localization of corrosion and the formation of defects (pitting, pits, etc.). Even alloyed steels are not always resistant in the presence of moisture and increased partial pressures of CO 2 , especially in the presence of additional factors of corrosive influence (temperature, aggressive impurities in gas, etc.).
-
Date submitted2021-06-01
-
Date accepted2021-07-27
-
Date published2021-10-21
Indicator assessment of the reliability of mine ventilation and degassing systems functioning
- Authors:
- Nina O. Kaledina
- Valentina A. Malashkina
The gas emission control in the mines is operated by ventilation and degassing systems that ensure the aerological safety of the mines or minimize the aerological risks. The ventilation system of the mine and its individual sites includes a significant number of technical devices and equipment, and the air tubes are mainly mining workings, the condition of which determines the quality of the ventilation network (its capacity) and depends on a number of mining factors. Similarly, one of the most important elements of the degassing system, which includes its own chain of technological equipment, are wells, and in some cases, mining workings. Thus, mine ventilation and degassing systems cannot be attributed to purely technical systems, since they include mining elements characterized by high variability of the determining parameters. To assess their reliability, it is necessary to use various combined methods that include additional characteristics in relation to the mining component. At the same time, the reliability of technical devices that ensure the functioning of mine ventilation and degassing systems largely determines the efficiency (stability and reliability) of these systems and, consequently, affects the level of aerological risks. The described approach to assessing the reliability of ventilation and degassing systems of coal mines when analyzing aerological risks is based on the developed system of risk indicators for the methane factor and will allow determining the risk dynamics in automatic mode based on monitoring the parameters of the ventilation and degassing system state.
-
Date submitted2021-03-17
-
Date accepted2021-04-12
-
Date published2021-06-24
Application of the resonant energy separation effect at natural gas reduction points in order to improve the energy efficiency of the gas distribution system
- Authors:
- Andrei M. Schipachev
- Alena S. Dmitrieva
Maintaining the gas temperature and the formation of gas hydrates is one of the main problems in the operation of gas pipelines. Development and implementation of new effective methods for heating the gas during gas reduction will reduce the cost of gas transportation, solve the problem of resource and energy saving in the fuel industry. Study is aimed at increasing the energy efficiency of the natural gas reduction process by using a resonant gas heater to maintain the set temperature at the outlet of the gas distribution station (GDS) and prevent possible hydrate formation and icing of the station equipment. Paper considers the implementation of fireless heating of natural gas and fuel gas savings of heaters due to the introduction of a thermoacoustic reducer, operating on the basis of the Hartmann – Sprenger resonance effect, into the scheme of the reduction unit. By analyzing the existing methods of energy separation and numerical modeling, the effectiveness of the resonant-type energy separation device is substantiated. Modification of the reduction unit by introducing energy separating devices into it will allow general or partial heating of natural gas by its own pressure energy. Developed technology will allow partial (in the future, complete) replacement of heat energy generation at a gas distribution station by burning natural gas.
-
Date submitted2020-06-12
-
Date accepted2020-06-15
-
Date published2020-12-29
Analysis of project organization specifics in small-scale LNG production
- Authors:
- Pavel S. Tcvetkov
- S. V. Fedoseev
Gas industry plays an important role in the global energy sector, and in the coming decades amountsof natural gas production will only increase. One of the fastest growing trends in gas industry is the production of liquefiednatural gas (LNG), which is associated with the necessity to organize flexible systems of gas supply to the regions,remote from gas extraction sites. Industrial structure of LNG production includes projects, belonging to several different groups depending to their scale, in particular, small-scale production (SSLNG), cumulative production capacityof which is approximately 10 % from the industry-wide one. Economic aspects of implementing such projects remainunderexplored, which does not allow to draw objective conclusions regarding the prospects of their implementationin particular regions.This paper contains a review of publications, devoted to SSLNG project studies, aimed at identifying specifics oftheir organization compared to projects of greater scale. The results demonstrate that the majority of internationalcompanies classify projects as SSLNG, if their annual production capacity is below 0.5 million tonnes per annum.Specific capital costs, as well as implementation timelines of such projects, are several times lower than those of projects with greater production capacity, which reduces their risks and minimizes barriers to market entry. Furthermore,SSLNG is the most decentralized subsector in gas industry, aiming to cover the market due to a growing numberof projects, not their specific production capacity. These specific features define significant prospects of SSLNGdevelopment in Russia, both in the context of energy supply to remote regions and diversification of export deliveries.
-
Date submitted2020-06-12
-
Date accepted2020-10-28
-
Date published2020-11-24
Spatial non-linearity of methane release dynamics in underground boreholes for sustainable mining
- Authors:
- Ada K. Dzhioeva
- Vladimir S. Brigida
The paper is devoted to the problem of increasing energy efficiency of coalmine methane utilization to provide sustainable development of geotechnologies in the context of transition to a clean resource-saving energy production. Its relevance results from the fact that the anthropogenic effect of coalmine methane emissions on the global climate change processes is 21 times higher than the impact of carbon dioxide. Suites of gassy coal seams and surrounding rocks should be classified as technogenic coal-gas deposits, while gas extracted from them should be treated as an alternative energy source. Existing practices and methods of controlling coalmine methane need to be improved, as the current “mine – longwall” concept does not fully take into account spatial and temporal specifics of production face advancement. Therefore, related issues are relevant for many areas of expertise, and especially so for green coal mining. The goal of this paper is to identify patterns that describe non-linear nature of methane release dynamics in the underground boreholes to provide sustainable development of geotechnologies due to quality improvement of the withdrawn methane-air mixture. For the first time in spatial-temporal studies (in the plane of CH 4 - S ) of methane concentration dynamics, according to the designed approach, the parameter of distance from the longwall ( L ) is introduced, which allows to create function space for the analyzed process (CH 4 of S-L ). Results of coalmine measurements are interpreted using the method of local polynomial regression (LOESS). The study is based on using non-linear variations of methane concentration in the underground boreholes and specific features of their implementation to perform vacuum pumping in the most productive areas of the undermined rock mass in order to maintain safe aerogas conditions of the extraction block during intensive mining of deep-lying gassy seams. Identification of patterns in the influence of situational geomechanical conditions of coal mining on the initiation of metastable gas-coal solution transformation and genesis of wave processes in the coal-rock mass allows to improve reliability of predicting methane release dynamics, as well as workflow manageability of mining operations. Presented results demonstrate that development of high-methane Donbass seams is associated with insufficient reliability of gas drainage system operation at distances over 40 m behind the longwall face. Obtained results confirm a working hypothesis about the presence of spatial migration of methane concentration waves in the underground gas drainage boreholes. It is necessary to continue research in the area of estimating deviation angles of “advance fracturing” zone boundaries from the face line direction. Practical significance of research results lies in the possibility to use them in the development of scientific foundation for 3D gas drainage of a man-made coal-methane reservoir, taking into account spatial and temporal advancement of the production face.
-
Date submitted2019-11-20
-
Date accepted2020-01-20
-
Date published2020-10-08
Effect of shear stress on the wall of technological pipelines at a gas condensate field on the intensity of carbon dioxide corrosion
The object of the study is a section of the gas and gas condensate collection system, consisting of an angle throttle installed on a xmas tree and a well piping located after the angle throttle. The aim of the study is to assess the impact of the flow velocity and wall shear stress (WSS) on the carbon dioxide corrosion rate in the area of interest and to come up with substantiated recommendations for the rational operation of the angle throttle in order to reduce the corrosion intensity. In the course of solving this problem, a technique was developed and subsequently applied to assess the influence of various factors on the rate of carbon dioxide corrosion. The technique is based on a sequence of different modeling methods: modeling the phase states of the extracted product, three-dimensional (solid) modeling of the investigated section, hydrodynamic flow modeling of the extracted product using the finite volume method, etc. The developed technique has broad possibilities for visualization of the obtained results, which allow identifying the sections most susceptible to the effects of carbon dioxide corrosion. The article shows that the average flow velocity and its local values are not the factors by which it is possible to predict the occurrence of carbon dioxide corrosion in the pipeline section after the angle throttle. The paper proves that WSS has prevailing effect on the corrosion intensity in the section after the angle choke. The zones of corrosion localization predicted according to the technique are compared with the real picture of corrosion propagation on the inner surface of the pipe, as a result of which recommendations for the rational operation of the angle throttle are formed.
-
Date submitted2020-03-20
-
Date accepted2020-05-24
-
Date published2020-06-30
Landscape monitoring studies of the North Caucasian geochemical province
The data on the geochemical features of the bedrocks and soils of the province are given. Considerable attention is paid to regional abundances, as well as enrichment and dispersion factors of the chemical elements in landscapes. Using the example of the North Caucasus, it is shown that for such indicators as phytomass, geological, geomorphological, and geobotanical features, it is possible to make a preliminary outlining of regional structures corresponding to geochemical provinces. At the same time, a subsequent geochemical study of these structures remains mandatory. Upon determining certain geochemical associations, geochemical provinces can be basically distinguished; to a large extent, geochemical properties of these accumulated and scattered associations of elements contribute to the regional soil geochemistry. The results of long-term monitoring studies of the North Caucasus geochemical province have shown that the key features of the regional landscapes are due to the composition of bedrock and the presence of a large number of ore deposits and occurrences. The data obtained are the basis for assessing the state of the environment in conditions of increasing anthropogenic impact, and the established regional abundances can be used to assess the degree of pollution in agricultural, residential, and mining landscapes.
-
Date submitted2019-05-30
-
Date accepted2019-09-04
-
Date published2020-02-25
Prospects for industrial methane production in the mine n.a. V.M.Bazhanov using vertical surface wells
The estimated methane resources in the coal stratum of Donbass are 798.5 billion m 3 , including 119.5 billion m 3 in the Donetsk-Makeevsky area. Such significant potential implies that methane can be used not only for industrial production and energy purposes but also as a commodity for the chemical industry. However, in practice, commercial production of methane from coal seams, as is done in the fields of the USA, Canada, India, and China, is not carried out, and methane, obtained as a by-product, is utilized for ensuring the safety of the main technological processes for coal mining. The main reasons for this are the difficult mining and geological conditions of bedding, low thickness and permeability, which does not allow to separate methane production into an independent type of activity due to its low profitability, especially with the use of new technologies based on hydraulic fracturing of coal seams. The assessment of the possibility of industrial methane production in the mine n.a. V.M.Bazhanov in the Donetsk-Makeevsky area of Donbass, which reserves equal to 23.7 billion m 3 , showed that a significant part of the methane reserves is concentrated in coal seams and interlayers with a gas content of 18.5-20.7 m 3 /m 3 . Moreover, in the host rocks, methane is practically in a liberated state. This circumstance makes possible the commercial production of methane for its utilization from the unloaded rock mass by wells drilled from the surface, without the use of hydraulic fracturing technology. The paper discusses the technology of methane extraction by a degassing well drilled from the surface into a coal-bearing stratum unloaded from rock pressure in a mining field of the 4th eastern face of the m 3 seam of the mine n.a. V.M.Bazhanov and its subsequent use as the fuel of an electric generator. It is shown that over the entire period of operation of the pilot well, the volume of actually produced methane exceeded the design value by 23 %, and the cost of the gas produced amounted to 1535 rubles per 1000 m 3 , which is more than 3 times lower than the market price for natural gas for consumers in the Russian Federation. This made it possible to make a conclusion about the possibility of industrial extraction of mine methane using vertical surface wells for its subsequent utilization in power plants, which does not imply the usage of hydraulic fracturing technology.
-
Date submitted2019-01-22
-
Date accepted2019-03-16
-
Date published2019-06-25
Key factors of public perception of carbon dioxide capture and storage projects
- Authors:
- S. V. Fedoseev
- Pavel S. Tcvetkov
One of the major challenges of the modern world is the problem of global warming, the solution of which requires the implementation of a set of strategic projects in the field of transition of the energy sector to the path of environmentally balanced development. One of the ways to implement this transition is the development of technologies for capturing and storage of technogenic carbon dioxide, which is recognized as the main one of greenhouse gases. At the same time, in the Russian context, the most expedient is the implementation of technological chains for capturing and storing CO 2 which are aimed at enhanced oil recovery, the effectiveness of which has been proven by world practice. Implementation of these projects requires consolidation of efforts of many parties, including government agencies, enterprises-issuers (power generating facilities and energy-intensive industry), oil-producing enterprises, non-state environmental organizations, media and public. World practice has many examples when uncoordinated actions of one of the stakeholders led to the closure of such a project, and therefore it is necessary to develop a mechanism of interaction between them, taking into account the specifics of Russian conditions. One of the least studied and controversial aspects of this interaction is to involve the public in the implementation of national carbon intensity programs and the local population in the implementation of a specific project. Research in this field has been conducted in the world over the past 14 years, which allowed the current research base to be used to develop fundamental principles for the development and promotion of CO 2 capture and storage technologies in Russia. Key factors affecting the perception of such projects by public were also analyzed and systematized. The research identified the main arguments for and against the development of CO 2 capture and storage technologies.
-
Date submitted2018-07-12
-
Date accepted2018-09-16
-
Date published2018-12-21
Environmental Geochemical Assessment of Technogenic Soils
- Authors:
- G. I. Sarapulova
The purpose of this study was to obtain diagnostic features and criteria for the distribution of heavy metals in technogenically altered soils in the area of industrial facilities, depending on their altered geochemical properties, which make it possible to fix chemical elements in landscapes (the formation of geochemical barriers). On the basis of the geoecological assessment, disturbance of the soil buffer properties, which is reflected in the ionic composition change, alkalization, pH increase, and sulfate-chloride salinization have been revealed. This forms the heavy metals alkaline barrier. For example, in case of Cu, Pb, Zn, and N, it contributes to their accumulation and subsequent concentration in the soil layer due to the exchange interactions between chemical elements and Na + , K + , Ca 2+ cations. Soil saturation with sulphates also increases the probability of metals demobilization in the soil layer. It has been shown that intra-sectional soil migration of oil products (one of the most common pollutants of industrial areas) and chemical elements occurs at a depth of 30-50 cm, where the oil products based on a clay sorption layer form a technogenic barrier.
-
Date submitted2018-07-02
-
Date accepted2018-09-04
-
Date published2018-12-21
Strategic Planning of Arctic Shelf Development Using Fractal Theory Tools
- Authors:
- V. S. Vasiltsov
- V. M. Vasiltsova
The paper justifies the necessity to utilize new methods of strategic planning in oil and gas field exploitation in the Arctic shelf during the implementation of high technology diversified model of development for oil and gas companies (OGC) based on principles and tools of fractal theory. It has been proved that despite its challenging conditions the Arctic represents not only resource potential of the country and a guarantee of national safety, but also a key driver of market self-identification and self-organization of OGCs. Identified and analyzed problems in institutional procurement of shelf development and utilized methods of strategic planning and project management, both on the levels of state and corporate governance, demonstrate that reductive approach of the fractal theory allows to take into account diversification of heterogeneous multicomponent project models, which can be reduced to a single management decision with inverse iterations of neural network modelling. Suggested approach is relevant for strategic planning not only on the stage of investment portfolio justification, but also for identification and assessment of project risks; ranking of projects according to the order of their implementation; back and - forth management (monitoring and supervision) and project completion. It has been detected that such basic properties of the fractal as self-similarity, recurrence, fragmentation and correlation between all fractal dimensions allow to systematize chaotically changing values of market parameters in the Arctic shelf development project, which provides an opportunity to forecast market development with minimal prediction errors.
-
Date submitted2016-09-06
-
Date accepted2016-11-13
-
Date published2017-02-22
Justified selection of a seam degassing technology to ensure safety of intensive coal mining
- Authors:
- S. V. Slastunov
- E. P. Yutyaev
The paper contains main aspects of methodological approach to objective analytic assessment of maximum permissible output of the mine faces from the viewpoint of gas factor. Analytic forecast is centered around the assessment of methane inflow into the face area from all possible sources, based on fundamental physical laws, modern tools of mathematical modeling and in-situ tests of main properties and state parameters of the gas-bearing coal formation. Objective and reliable estimation of permissible outputs is a starting point for justified selection of a seam degassing technology, that has to be based on time factor and predicted value of gas recovery from a coal seam to a degassing well. Recommendations have been formulated on the selection of degassing technology for the coal seam «Boldyrevsky» of the Kirov mine, based on the use of cutting-edge technological schemes (hydraulic fracture, carried out from development workings, etc.), successfully implemented on the mentioned site.
-
Date submitted2015-12-24
-
Date accepted2016-02-04
-
Date published2016-12-23
Geodynamic methods for assessing methane distribution in bituminous coal deposits and measures to intensify methane fluxes during mine gas drainage
- Authors:
- E. V. Goncharov
- S. V. Tsirel
This paper explores states of methane within the coal bearing stratum and shows heavy dependency of the intrastratal gas migration on the forms of porous space and petrographic properties of coal. The adsorbed methane is found to be predominant in the coal of Kuznetsk Basin. Different forms of coal diffusion and filtration are described revealing their dependency on geological and thermodynamic conditions. The paper provides justification for the primary focus on geodynamic processes when designing gas drainage systems and applicability of morphometric methods and remote sensing data for their identification. The significance of researches into the processes activating exothermic reactions resulting in methane transition to free state is explained. The paper presents the results of using seismic-acoustic stimulation techniques as one of the practical approaches to addressing this issue. Results of successful industrial testing have been compared with the results of numerical modelling of stress-strain state, which can also be managed through seismic-acoustic stimulation.
-
Date submitted2015-10-01
-
Date accepted2015-12-11
-
Date published2016-08-22
The technology of extracting gaseous fuel based on comprehensive in situ gasification and coalbed degassing
The study considers a comprehensive technology (designed and patented by the authors) of developing coal and methane deposits which combines in situ gasification of lower coalbeds in the suite of rock bump hazardous gassy beds, extraction of coal methane and mechanized mining of coal. The first stage of the technology consists in mining gaseous fuel that enables one to extract up to 15-20 % of total energy from the suite of coalbeds. Geodynamic zoning is used to select positions for boring wells. Using the suggested technology makes it possible to solve a number of tasks simultaneously. First of all that is extracting gaseous fuel from the suite of coalbeds without running any mining works while retaining principal coalbeds in the suite and preparing them for future processing (unloading and degassing). During the first phase the methane-coal deposit works as a gas deposit only, the gas having two sources – extracted methane (which includes its locked forms, absorbed and adsorbed) and the products of partial incineration of thin coalbeds, riders and seams from thee suite. The second stage consists in deep degassing and unloading of coal beds which sharply reduces the hazards of methane explosion and rock bumps, thus increasing the productivity of mechanized coal mining. During the second stage coal is mined in long poles with the account of degassing and unloading of coal beds, plus the data on gas dynamic structure of coal rock massif.
-
Date submitted2014-12-28
-
Date accepted2015-02-21
-
Date published2015-12-25
Modeling of rock massif geomechanical state at gas extraction from coal seams
- Authors:
- M. G. Mustafin
The article describes the method of modeling a coal seam stress-strain state and an enclosing rock massif when degasified. An approach to defining the model input parameters, calculated with the porosity and gas pore pressure coefficient, was shown. The importance of preliminary calculations, indicating possible coal seam shrinkage and surface subsidence was underlined. It shows formation mechanism for coal seam zones with elevated gas pressure, where gas recovery is efficient.
-
Date submitted2010-07-30
-
Date accepted2010-09-10
-
Date published2011-03-21
Definition areas of possible migration gas fromthe reservoir by cross-hole seismic tomography method
- Authors:
- N. A. Poznyakova
Possibilities of cross-hole a seismoacoustic tomography method for studying tightness a tire-cover of a reservoir underground storehouse of gas (USG), created in water-bearing horizont. Research cross-hole spaces for definition zones possible migration and accumulation gas outside of a trap are considered. The system of supervision used at carrying out cross-hole seismoacoustic tomography is proved, the example of revealing zones migration and accumulation gas outside from reservoir is resulted. Prospects application the given method on USG in a monitoring mode are defined.
-
Date submitted2010-07-28
-
Date accepted2010-09-07
-
Date published2011-03-21
Modelling cavities nearwell areas for studyind of possibilities neitron well methods
- Authors:
- N. A. Poznyakova
Look into the possibility neutron method geophysical logging for determination zones of cavity nearwell areas gas reservoirs and determine the filler cavities. Relevant practicability using these methods on underground gas storage. Give an example these research on model and real conditions.
-
Date submitted2009-10-11
-
Date accepted2009-12-26
-
Date published2010-09-22
The analysis of factors, that cause processes of open hole wells’ destructions of Gatchina underground gas storage reservoir and prediction of sand effects
- Authors:
- D. V. Grishin
- A. V. Petukhov
- A. A. Petukhov
The peculiarities of elastic stresses in open hole wells’ of Gatchina gas storage reservoir are researched. It is revealed that in depression more than 1,5 MPa gas bearing rocks start to destroy. On the basis of studying of correlation relation between technological parameters of gas wells’ production and evacuation of sand the equations of plural regression are constructed. These equations are used to make prediction of sand evacuation at each producing gas well.
-
Date submitted2009-10-25
-
Date accepted2009-12-19
-
Date published2010-09-22
Principal technologies for prevention of natural dangers at coal mines
- Authors:
- Jozef Dubinsky
Modern mining of mineral resources to be the industry accepted by the society must meet the criteria for sustainable development. Work safety is its important element, which is a particular sphere in underground coal mines in the view of natural hazards occurring numerously, including the catastrophic failures. Among them are gas hazard, fires and rock burst hazard. The selected methodological solutions in terms of their recognition and technologies applicable for the actively combat of these threats, which are featured by high efficiency, have been pointed out.
-
Date submitted2009-10-18
-
Date accepted2009-12-17
-
Date published2010-09-22
Reuse of development workings as an element of providing the effective coal output
- Authors:
- M. A. Ilyashov
The article contains the results of application in a coal mine of a combined way for protection and support of development workings. This method combines a frame support, anchors and a cast support strip erected behind the longwale. The geomechanical substantiation of technological parameters, regulations and the field for efficient use of this method are given. Its introduction has allowed to increase the loads on longwale and to lower labour content and expenses for maintenance of butt entries.