-
Date submitted2023-12-07
-
Date accepted2024-11-07
-
Date published2025-04-07
Determination of the tangential component of cutting resistance during frozen sedimentary rock cutting using blocked, deeply blocked and cell cutting methods
Due to the insufficient accuracy of existing studies of frozen sedimentary rock cutting process for practical calculations, the article solves the problem of determining the tangential component cutting resistance for blocked, deep blocked and cell cutting, which are currently the most commonly used methods in earthmoving equipment. The cutting tool and rock mass force interaction is considered from the point of view of the emerging stresses, which act on the separated chip element. The analytical dependences for determining the tangential component of cutting resistance were obtained. The numerical explanation of the choice of cell cutting in relation to blocked and deeply blocked cutting is given. For all three methods of cutting, under equal geometrical parameters of the cutting tool and the physical and mechanical properties of the frozen rock, the numerical value of the tangential component of cutting resistance is obtained. The comparison of the cutting resistance estimated values has shown that cell cutting requires relatively less energy and is preferred during the process of frozen sedimentary rock excavation. During field and laboratory investigations with the use of a multi-purpose cutting stand, a sufficient convergence of the analytical statements with the physics of frozen sedimentary rock cutting process was established. The results of the research allow a more reasonable approach to the adjustment of existing methods for determining the required tractive force and power for the drive of an excavation machine, and, therefore, to the actual efficiency and profitability of work.
-
Date submitted2024-05-17
-
Date accepted2025-03-27
-
Date published2025-03-27
Determination of impact hazard potential of rocks in the Norilsk Industrial Region
The deeper the mineral deposits developments are, the worse the mining and geological conditions become. Significant growth of stress level in the rock mass contributes to possible manifestation of rock pressure in dynamic form. The resulting task of assessment of rock impact hazard is closely related to the task of obtaining more accurate results of compression tests of samples in rigid or servohydraulic test presses using graphs of their full deformation. This approach requires special expensive equipment, considerable time resources, and sufficient core material. Therefore, it is important to have an approach that allows to assess the propensity of rocks to brittle fracture with research methods simple enough not to result in the loss of quality and reliability of the obtained results. This paper presents the results of laboratory tests of rocks from the Norilsk Industrial Region to determine their tensile and compressive strengths. Test methods involved both domestic and foreign standards for determining the value of the brittleness coefficient. The impact hazard potential of rocks was determined using the Kaiser criterion. It is found that the tested lithological types (rich sulfide ores, hornblende, disseminated ores, and gabbro-dolerite rocks), with the exception of anhydrite, have a low impact hazard potential.
-
Date submitted2022-05-20
-
Date accepted2023-04-03
-
Date published2024-02-29
Impact of carbon dioxide on the main geotechnical quality criteria and preparation cost of cemented paste backfill
There is a global upsurge in the use of cemented paste backfill (CPB) for various mining functions. However, the cost of the Portland cement binder is prohibitive, thus warranting strategies to reduce cement usage without overly diminishing the CPB quality. Since carbon dioxide is used for patented sand moulding processes, this study is premised on that physicochemical ability of CO2 to enhance the curing of consolidated inorganic materials. It evaluated the impact of carbon dioxide on the uniaxial compressive strength UCS and preparation cost of CPB standard samples (ASTM C109). The preparation cost was delimited to the purchase cost of the Portland cement. The backfill material was silica sand tailings with 4.5 wt.% Portland cement binder and a water-cement ratio of 7.6. Distilled water of pH 5.4 was used for the control samples while variable amounts of carbon dioxide were dissolved in distilled water to generate carbonated mixing water with pH values of 3.8; 4 and 4.2. The lower the carbonated water pH, the higher is the CO2 concentration. UCS tests were conducted on the samples after curing for 3, 7, 28, and 90 days. There was an observable increase in the UCSs and reduction in curing time with increasing carbon dioxide. Samples prepared with carbonated water of pH 3.8 had almost double the strength of those prepared with pure distilled water of pH 5.4, implying that more dissolved CO2 corresponds to higher CPB strength. This is supported by the trendline equations for the graphical simulation of strength on curing time. Thus, CPB with much less binder can be expected to attain the requisite UCS if carbon dioxide is incorporated. The average reduction in Portland cement consumption was 0.61 %, which translates to a cost saving of the same percentage points. If calculated over the operational life of a mine, this is a massive saving of millions of dollars.
-
Date submitted2021-09-01
-
Date accepted2022-10-07
-
Date published2022-12-29
Parameter determination of the method of directional unloading of the reservoir based on physical modelling on a true triaxial loading setup
The article presents a theoretical and experimental substantiation of the method of directional unloading of the reservoir in fields with low-permeability reservoirs. The relevance of the article is due to the reduction of hydrocarbon resources in modern conditions and the need to create new efficient environmentally friendly technologies to develop hydrocarbon deposits with hard-to-recover reserves, primarily with low-permeability reservoirs. The results of a theoretical study of the stress-strain state in the vicinity of a well, both cased and open, are presented. They are necessary to develop programs for laboratory testing of core specimens from the studied fields. A technique for physical modelling of deformation processes in the bottomhole zone with a decrease in pressure at the well bottom in a true triaxial loading unit is described in order to determine the parameters of the process impact on the formation reservoir, leading to an increase in well productivity. The method was applied to the conditions of the low-permeability reservoir at the Verkhneviluchanskoye oil and gas condensate field in the southwest of the Republic of Sakha (Yakutia). Expe-rimental studies were carried out on a unique scientific unit for true triaxial loading, created at the IPMech RAS, the Triaxial Independent Loading Test System. The directional unloading method was adapted for the studied field, the process parameters of successful application of the method were determined: the bottomhole design, the drawdown values necessary to increase the permeability of the bottomhole formation zone.
-
Date submitted2022-05-18
-
Date accepted2022-07-21
-
Date published2022-11-10
Improving the method for assessment of bending stresses in the wall of an underground pipeline
- Authors:
- Ruslan V. Aginey
- Alexei A. Firstov
Brief information about modern methods for determining the bending stresses of the extended sections of underground main pipelines without access to the pipeline generatrix is given. The necessity of modernizing methods based on determining the configuration of the pipeline axis from the soil surface with subsequent calculation of bending stresses based on the obtained data is substantiated. A mathematical model that allows to calculate the optimal parameters for surveying the axis of the pipeline from the soil surface for a pipeline of arbitrary configuration and depth, when planning a study, is proposed. Bench tests of the BITA-1 pipeline finder were carried out to determine the error in measuring the depth of the pipeline axis. It is proved that the deviations of the pipeline finder data relative to the true values in narrow depth intervals follow a normal distribution and do not change their sign. The confidence intervals of the error in determining the depth of the pipeline axis for the BITA-1 device are presented.
-
Date submitted2021-12-21
-
Date accepted2022-06-20
-
Date published2022-11-10
Scientific justification of the perforation methods for Famennian deposits in the southeast of the Perm Region based on geomechanical modelling
The article presents the results of analysing geological structure of the Famennian deposits (Devonian) in the Perm Region. Numerical modelling of the distribution of inhomogeneous stress field near the well was performed for the two considered types of perforation. With regard for the geometry of the forming perforation channels, numerical finite element models of near-wellbore zones were created considering slotted and cumulative perforation. It is ascertained that in the course of slotted perforation, conditions are created for a significant restoration of effective stresses and, as a result, restoration of reservoir rock permeability. Stress recovery area lies near the well within a radius equal to the length of the slots, and depends on the drawdown, with its increase, the area decreases. From the assessment of failure areas, it was found that in case of slotted perforation, the reservoir in near-wellbore zone remains stable, and failure zones can appear only at drawdowns of 10 MPa and more. The opposite situation was recorded for cumulative perforation; failure zones near the holes appear even at a drawdown of 2 MPa. In general, the analysis of results of numerical simulation of the stress state for two simulated types of perforation suggests that slotted perforation is more efficient than cumulative perforation. At the same time, the final conclusion could be drawn after determining the patterns of changes in permeability of the considered rocks under the influence of changing effective stresses and performing calculations of well flow rates after making the considered types of perforation channels.
-
Date submitted2021-09-29
-
Date accepted2022-05-11
-
Date published2022-07-13
Tensor compaction of porous rocks: theory and experimental verification
Compaction in sedimentary basins has been traditionally regarded as a one-dimensional process that ignores inelastic deformation in directions orthogonal to the active load. This study presents new experiments with sandstone demonstrating the role of three-dimensional inelastic compaction in cyclic true triaxial compression. The experiments were carried out on the basis of a triaxial independent loading test system in the Laboratory of Geomechanics of the Ishlinsky Institute for Problems in Mechanics of the Russian Academy of Science. The elastic moduli of the material were estimated from the stress-strain curves and the elastic deformations of the sample in each of the three directions were determined. Subtracting the elastic component from the total deformation allowed to show that inelastic compaction of the sandstone is observed in the direction of active loading, whereas in the orthogonal directions there is a expansion of the material. To describe the three-dimensional nature of the compaction, a generalization of Athy law to the tensor case is proposed, taking into account the role of the stress deviator. The compaction tensor and the kinetic equation to describe the evolution of inelastic deformation, starting from the moment of the load application are introduced. On the basis of experiments on cyclic multiaxial compression of sandstone, the identification and verification of the constructed model of tensor compaction were carried out. The possibility of not only qualitative, but also quantitative description of changes in inelastic deformation under complex cyclic triaxial compression is shown.
-
Date submitted2020-07-30
-
Date accepted2021-03-02
-
Date published2021-04-26
Experimental study of thermomechanical effects in water-saturated limestones during their deformation
Stability control of elements of stone constructions of various structures is a prerequisite for their safe operation. The use of modern methods of non-destructive diagnostics of the stress-strain state of such constructions is an effective, and in many cases the only way to control it. Studies of thermal radiation accompanying the processes of solid bodies deformation allowed to justify and develop a method that allows to obtain non-contact information about changes in the stress-strain state in various types of geomaterials, including limestones. However, studies of the water saturation influence of rocks on the thermal radiation parameters recorded in this way are currently superficial. Taking into account the water saturation degree of rocks is necessary when monitoring the mechanical condition of stone structures that are in direct contact with water. The main purpose of this work is to study the dependences of changes in the intensity of thermal radiation from the surface of limestone samples with different humidity under conditions of uniaxial compression. The obtained results showed the expected significant decrease in the mechanical properties (uniaxial compressive strength and elastic modulus) of water-saturated samples in comparison with dry ones. At the same time, a significant increase in the intensity of thermal radiation of limestone samples subjected to compression with an increase in their water saturation was recorded, which makes it necessary to take into account the revealed regularity when identifying changes in the stress state of stone structures established according to non-contact IR diagnostics in real conditions.
-
Date submitted2020-05-29
-
Date accepted2020-09-16
-
Date published2020-11-24
Numerical modeling of a double-walled spherical reservoir
Extensive and important class of multilayer shell structures is three-layer structures. In a three-layer structure, a rigid filler plays an important role, due to which the bearing layers are spaced that gives the layer stack high rigidity and durability with a relatively low weight. By combining the thicknesses of the bearing layers and the filler, the desired properties of a three-layer shell structure can be achieved. Compared with traditional single-walled, three-layer construction has increased rigidity and durability, which allows reducing the thickness and weight of the shells. In order to reduce the metal content of the spherical reservoir for storing liquefied gases, this work considers the design of a double-walled reservoir, in which the inter-wall space is filled with reinforced polyurethane. Numerical modeling made it possible to determine the parameters of the stress-strain state of the structure with an error of no more than 5 %. It has been established on the example of a reservoir with a volume of 4000 m 3 that the spatial structure of the spherical reservoir wall can reduce the metal content up to 19 %. Field of application for the research results is the assessment of the stress-strain state of spherical reservoirs at their designing. Method for building the structure of a double-walled spherical reservoir in the SCAD software has been developed, which allows calculating the stress-strain state (SSS) by the finite element method. Numerical model of a double-walled spherical reservoir has been developed. It was found that to obtain calculation results with an error of P ≤ 5 % the size of the final element should not exceed 300×300×δ mm. Design of a double-walled spherical reservoir was investigated. Design parameters have been established to ensure the operational reliability of the structure with a decrease in metal content in comparison with a single-wall reservoir by 19 %.
-
Date submitted2019-11-04
-
Date accepted2020-01-12
-
Date published2020-10-08
PDC cutter pressure on plastic-brittle rock in the process of its destruction
- Authors:
- Oleg B. Trushkin
- Hamzja I. Akchurin
Presently, there are no methods for calculating the parameters of the drilling practices with rock-cutting tools equipped with polycrystalline diamond composite (PDC cutters). To create such a method requires the studying their work. The article presents the results of bench studies of the PDC cutters in the process of a rock sample breakdown when reproducing the actual layout of the cutters on the working surface of the bit. An important parameter of PDC cutters operation, which is necessary for the bit load analysis, is the pressure of the cutters on the rock during its breakdown. The total pressure of a cutter on the rock can be broken into two mutually perpendicular components: the forcing pressure and the cutting pressure. It is proposed to evaluate the PDC cutters loading at breakage of rocks of different hardness using relative values of forcing and cutting pressures, which are calculated relative to the yield strength of the rock by the die. It is established that the variability of the average relative pressures of forcing and cutting is significantly influenced by drifting per bit turnover and the radius of the cutter on the bit. The dependences of the maximum relative pressures of PDC cutters at the plastic-brittle rock breakdown on the drifting per bit turnover and the radius of the cutter location on the bit are obtained. It has been established that when drifting up to 0.4 mm per turn, the main mechanism of breakdown is cutting, and with the increase of the breakdown depth, the process of forcing becomes decisive.
-
Date submitted2020-01-09
-
Date accepted2020-01-20
-
Date published2020-02-25
Mechanical Properties of Sandstone using non-Destructive Method
- Authors:
- H. Rajaoalison
- A. Zlotkowski
- G. Rambolamanana
The understanding of physical and mechanical properties of rock is considered as critical in drilling, geo-engineering, and construction applications. As an example, the awareness of these rock parameters contributes to avoid or minimizing instability around the wellbore while drilling. The laboratory experiment of understanding of these parameters can be done in two-different ways: static, where the sample subjects to destruction after the test and dynamic, known as non-destruction method. The non-destructive method using ultrasonic waves under a series of different stress conditions, starting from 7 to 56 MPa with incrementation of 7MPa, has been used in this paper in order to characterize the mechanical properties of dry Zbylutów sandstone at 20 and 80°C. The velocity of primary (P) and secondary (S) waves within these ranges has been recorded in order to understand the behavior of the mechanical properties. The results showed that the Young’s modulus, bulk modulus, shear modulus, and Lame’s constant of Zbylutów sandstone have a positive correlation with good coefficient correlation with the increased stress, while the Poisson’s ratio showed a negative correlation. Besides, the effect of temperature on the rock parameters is approved by the decrease of primary wave velocity in this two-different temperature range. Such results are necessary when preparing the appropriate mud weight for drilling process, which is related to wellbore instability.
-
Date submitted2020-01-09
-
Date accepted2020-01-26
-
Date published2020-02-25
Mining excavator working equipment load forecasting according to a fuzzy-logistic model
- Authors:
- V. S. Velikanov
Due to the fact that the loads occurring in the working equipment of mining excavators are determined by a large number of random factors that are difficult to represent by analytical formulas, for estimating and predicting loads the models must be introduced using non-standard approaches. In this study, we used the methodology of the theory of fuzzy logic and fuzzy pluralities, which allows to overcome the difficulties associated with the incompleteness and vagueness of the data in assessing and predicting the forces encountered in the working equipment of mining excavators, as well as with the qualitative nature of these data. As a result of computer simulation in the fuzzyTECH environment, data comparable with experimental studies were obtained to determine the level of loading of the main elements of the working equipment of mining excavators. Based on a representative sample, a statistical analysis of the data was performed, as a result of which the equation of linear multiple stress regression in the handle of mining excavators was obtained, which allows to make an accurate forecast of the loading of the working equipment of the excavator.
-
Date submitted2018-06-27
-
Date accepted2018-08-31
-
Date published2018-12-21
Numerical modeling of a stress-strain state of a gas pipeline with cold bending offsets according to in-line inspection
Knowledge of the current stress-strain state of any section of the pipeline allows you to make informed decisions on its operation, maintenance and repair, as well as on the prediction of the technical condition. The task of determining the characteristics of the stress-strain state of a gas pipeline section that has cold bend offsets (CBO) according to in-line inspection (ILI) is considered. The bent part of CBO is characterized by the presence of residual stresses and deformations in the wall of the offset, which contribute to the overall level of the stress-strain state of the gas pipeline operating under external and internal loads. Using the results of in-line diagnostics, numerical modeling and a solution, the change in the values of longitudinal stresses, is determined and the need to take into account residual stresses in the zone of elastic-plastic deformations of cold bend offsets is shown.
-
Date submitted2015-08-13
-
Date accepted2015-10-29
-
Date published2016-04-22
Multicriteria estimation of bearing capacity of geomaterials
- Authors:
- I. A. Brigadnov
In the article the problem of an estimation of bearing capacity of geomaterials as a deform-able solid is considered in the current configuration, which may be as the reference (undeformed) or the actual (deformed). We propose an original variational approach to the problem for stresses in selected subdomains, in which, depending on different engineering considerations, average in-tegral values of different component of stresses are estimated and from their aggregate the bearing capacity of the current configuration of the solid is estimated regarding to given external influ-ences. In each of the selected subdomain the weakest stress field is obtained which is globally bal-anced with external influences. For example, the assessment of the average integral hydrostatic pressure is needed for study of bearing capacity of geomaterials.
-
Date submitted2009-10-06
-
Date accepted2009-12-30
-
Date published2010-09-22
Research of deformation, strength and filtration characteristics of Nizhnechutinskoe oil field’s reservoirs in case of depression making in the process of oilwells exploitation
- Authors:
- A. V. Petukhov
- A. A. Petukhov
It is determined that main reasons of permeability reservoirs decrease in Nizhnechutinskoe oil field are capillary pressures and elastic stresses, appearing at depression making. It is displayed that to reduce tangential stresses in oil bearing reservoirs it is expedient to make vertical slits in oilwells’ open holes.
-
Date submitted2009-10-14
-
Date accepted2009-12-11
-
Date published2010-09-22
Investigation of present-day stress-strain state of rock mass by the results of observations at geodynamic polygons
- Authors:
- S. N. Savchenko
- E. V. Kasparyan
- Yu. G. Smagina
The methods are suggested for treatment of the results of optical distance and levelling measurements at the underground geodynamic polygons involving in their calculation the tensors of additional stresses and deformations, component of rotation and specific energy of deformability. As an example, consideration is given to changes in time of movements, deformations and specific energy of deformability at one of geodynamic polygons of the Kola peninsular.
-
Date submitted2009-10-26
-
Date accepted2009-12-27
-
Date published2010-09-22
Support of geodynamic safety in mining of the Khibini deposits
The paper deals with the problems of geodynamics in mining of the Khibini deposits. Description is given to the complex of organizational-technical arrangements for provision of geodynamic safety at the Apatit Co and to principal trends of its development.
-
Date submitted2009-10-07
-
Date accepted2009-12-22
-
Date published2010-09-22
Providing of safe conditions for mining of shaftbottom protective pillars in deep ore mines at Тalnakh
- Authors:
- V. A. Zvezdkin
- A. G. Anokhin
- R. B. Galaov
Consideration is given to the causes complicating the mining of shaftbottom pillar and protection of shaft lining. The analysis is given to the formation of stress-strain state of the protective pillar and its enclosing rocks. Practical recommendations are given for control of deformation and stresses in the shaftbottom mass during extraction of protective pillars in deep ore mines at Talnakh.
-
Date submitted2009-10-18
-
Date accepted2009-12-09
-
Date published2010-09-22
Influence of blocky-hierarchy structure of geological medium on the forming of natural and technogenic geodynamic fields in the North-West part of the Amur geoblock
- Authors:
- I. Yu. Rasskazov
- B. G. Saksin
On the example of the South-Argun uranium ore district of Zabaikalie consideration is given to the interaction of regional and local fields of stresses. The district includes a number of deposits prone to rock bursts. The performed analysis contains data on recent geodynamics of the explored part of the Amur geoblock as well as on geomechanical and geologo-structural materials of Tulukuev caldera and of Antey deposit. It is shown that with the use of the M.A. Sadovsky relationship the indices of local structural forms of a row are subjected to unified laws of deformation and fracturing. Conclusion was made that at the beginning of deposit exploitation the direction of action of stress field within rock mass conformed to regional one, and then it considerably changed under influence of large-scale mining operations.
-
Date submitted2009-09-07
-
Date accepted2009-11-17
-
Date published2010-06-25
The transformation of zone of potentially dangerous accumulative wrecks in a layeked mining roof when combined effect of the rock pressure and shock stress waves
- Authors:
- V. V. Karpenko
The transformation of potentially dangerous zone of wrecks accumulation in the layeredroof of the mining system is considered, in the time of combined action of geostatic pressure and tension shok wave. The explosion wave front is suggested to be parallel to the proximate handing roof environs discontinuity. Under this condition in the article is considered the influence of levels of critical stress and the depth of opening location on the change of implicitly dangerous zone of faults accumulation in the layers of the root stone.
-
Date submitted2009-08-25
-
Date accepted2009-10-24
-
Date published2010-02-01
Geomechanical substantiation of parameters of the fastening of railway tunnels in the conditions of the North Caucasus
- Authors:
- N. A. Belyakov
The article presents the rationale of temporary supports used in the drilling of new mines, which provides for the construction of model projects of reconstruction of old tunnels. Finite-element method analyzed the changes of stress-strain state containing tunnel complex array during the drilling of new mines. Based on the analysis, a number of findings to explore the possibility of reducing the thickness of the permanent support of new mines in tunnel complex - the new tunnel, and transport and drainage culvert.
-
Date submitted2009-07-29
-
Date accepted2009-09-15
-
Date published2010-04-22
Preconditions for application of supports of different types in productive workings of low-thick gently-pitching deposits in tectonically stressed massif (for conditions of the Karnasurt ore mine)
- Authors:
- A. V. Lovchikov
- A. V. Matytsyn
The paper presents the data on the mining-geological conditions for mining and types of stope supports applied at the Karnasurt Mine, the Lovozersky rare-metal deposit. The peculiar feature of mining conditions is the presence of high subhorizontal tectonic stresses in the rock masses, which make the stope roofs more stable, allowing application of non-reinforced types of support.
-
Date submitted2009-07-24
-
Date accepted2009-09-20
-
Date published2010-04-22
Investigation of stress-strain state of floor of the dividing mass of deep-lying ore mines at Тalnakh
The paper contains the results and analysis of the formation of stress-strain state in blocky structure enclosing the dividing mass. The regularities were established on the influence of blocky structure undermining on stress state of the floor of dividing mass. Recommendations are given for the safe mining in the dividing rock mass.
-
Date submitted2009-07-21
-
Date accepted2009-09-28
-
Date published2010-04-22
The determination of the volume stress-strain conditions of the rock massive with the circular outline mining ensrined with the anchors
- Authors:
- A. G. Protosenya
- N. A. Belyakov
In the article the analysis of consolidating effect from application of the anchor fastening, which using at driving of transport tunnels in the conditions of North Caucasus is produced. The change of the stress-strain condition of the rock massive, which is weaked by the mining of the circular outline is certain with the finite-elements method. On the basis of the executed design the row of graphic dependences, which describes changing of the sizes of limitary areas depending on strength and deformational properties of the rocks. Due to results of the conducted work the direction of further researches is seted.
-
Date submitted2009-07-09
-
Date accepted2009-09-03
-
Date published2010-04-22
The stress-strain state of the massive of the loose ores in the Yakovlevsky deposit around the minings which were drilled with the combines or with drilling-blast technology
The article presents the consistent patterns of the changes in stress-strain state of the massive by the minings of the first stage of protective overlapping in the Yakovlevsky deposit. The change of the stress-strain condition of the rock massive, which is weaked by the mining was determined by the method of finite elements. The stresses distribution in the massive, the displacement of the contour of the minings, the size of conditional zones of non-linear deformations has been obtained. For stoping passes at the first stage the cutting with combine and application of fastening with the anchors has been suggested.