-
Date submitted2024-06-04
-
Date accepted2025-01-28
-
Date published2025-04-04
Impact of dry and wet magnetic separator process parameters on iron oxide removal from Egyptian feldspar ore
The demand for feldspar as a raw material in the ceramic industry is continuously increasing. Feldspar is abundant in the Earth's crust and typically found alongside other silicate minerals, as well as titanium and iron oxides. This study aims to reduce the iron oxide content in feldspar ore from the Wadi Zirib region and achieve an optimal grade of feldspar concentrate for various industrial uses. The research involved dry and wet magnetic separation techniques followed by leaching with oxalic and citric acids to minimize iron impurities and enhance optical properties. The factors affecting the dry magnetic separation, for feldspar size of –250+45 µm, were optimized using the Box – Behnken factorial design and a non-magnetic concentrate with 0.29 % Fe2O3 and an 92.19 % feldspar yield was obtained. The wet magnetic separation for feldspar fines of size –45µm was optimized and a concentrate with 0.27 % Fe2O3 was achieved. The acid leaching was conducted on the non-magnetic feldspar concentrates using oxalic and citric acid. Oxalic acid was more successful in reducing iron oxide of dry (to 0.19 %) and wet (to 0.12 %) non-magnetic feldspar concentrates. The optical properties of the leached concentrates were improved compared to the original sample, as the whiteness improved up to 90 %.
-
Date submitted2023-12-15
-
Date accepted2024-06-13
-
Date published2025-02-25
Development of equipment and improvement of technology for inertial thickening of backfill hydraulic mixtures at the final stages of transportation
The results of the study of the functioning of the developed thickening equipment as part of the stowing complex for the formation of a flow of high-concentration hydromixture are presented. To explain the operation of the hydrotransport system of the stowing complex, equipped with a thickener of the developed design, its basic diagram is presented. A mathematical model has been created that describes the mechanism of inertial sedimentation of a solid component of a hydraulic mixture in a working chamber equipped with hydrodynamic profiles. Interaction with the profile leads to flow stratification due to a change in the trajectory of movement and a decrease in speed. The interval of rational velocity of primary pulp entering the input of the working chamber of the inertial thickener is substantiated. The synthesis of solutions of the thickening process model is performed in the COMSOL Multiphysics and Ansys Fluent programs. This made it possible to eliminate physical contradictions in the operation of the equipment and justify the overall dimensions of its main elements, ensuring the implementation of the mechanism of inertial sedimentation of the slurry. It was found that the concentration of the thickened flow at the outlet branch pipe of the thickener working chamber is determined by the level of the primary hydraulic fluid velocity, the characteristic length of the section of interaction with the deflecting profile, and the ratio of the flow and attack angles. A nomogram of the dynamics of the change in the hydraulic fluid concentration in the section of the outlet branch pipe depending on the ratios of the overall dimensions of the deflecting profile of the working chamber was compiled. The results of the study allowed formulating recommendations for selecting the dimensions of the thickener's deflecting hydrodynamic profile to form a flow of hydraulic mixture with a concentration of about 50 % by weight. The developed equipment can be used in a stowage complex and will increase the range of supply of the stowage mixture. This is due to the fact that a flow of primary slurry with a low concentration, due to lower pressure losses, can be moved in a pipeline system over a greater distance than a flow with a high filler content. The use of a thickener at the final stage of transportation is intended to increase the concentration of the hydraulic mixture immediately before production.
-
Date submitted2022-03-01
-
Date accepted2024-06-03
-
Date published2024-12-25
Study of the possibility of using high mineralization water for hydraulic fracturing
The results of laboratory studies aimed at developing hydraulic fracturing fluid based on alternative sources of high mineralization water are presented. It is shown that Cenomanian sources have the most stable mineralization parameters, while bottom water and mixed waters collected from pressure maintenance systems differ significantly in their properties, with iron content varying several times, and hardness and mineralization undergoing substantial changes. The quality of the examined hydraulic fracturing fluids based on alternative water sources is confirmed by their impact on residual permeability, as well as residual proppant pack conductivity and permeability. The experimental results show similar values for these parameters. The comprehensive laboratory studies confirm the potential for industrial use of high mineralization water in hydraulic fracturing operations.
-
Date submitted2022-10-29
-
Date accepted2023-10-25
-
Date published2024-04-25
Assessment of rock massif sustainability in the area of the underground research laboratory (Nizhnekanskii Massif, Enisei site)
The study presents the results of the research on geodynamic and geological conditions of the Enisei site (Krasnoyarsk Krai), chosen for the construction of an underground research laboratory. The laboratory is being built at a depth of 500 m to assess the suitability of the rock mass for burying high-level radioactive waste. The rocks consist of weakly fractured gneisses, granites, and dikes of metadolerites. Field observations were conducted on bedrock outcrops. They included the determination of rock mass quality indicators, measurement of rock fracturing, and a rating classification of stability using N.Barton's method. GNSS observations were also made to monitor surface deformations. These data were used to develop a three-dimensional structural model, including lithology, fault disruptions, intrusive bodies, elastic-strength properties of rocks, and the sizes of zones influenced by faulting. It will serve as a basis for boundary conditions and the construction of three-dimensional variational models of stress-strain states, identifying zones of concentration of hazardous stresses, and planning in situ geomechanical experiments in underground mines of the laboratory. The obtained values of the modified QR index for the main types of rocks allowed their classification as stable and moderately stable, corresponding to strong and very strong rocks on Barton's scale and the massif rating according to geomechanical classification.
-
Date submitted2022-12-01
-
Date accepted2023-01-19
-
Date published2023-12-25
Inclusions of diamond crystals in the tourmaline of the schorl-uvite series: problems of genesis
The mineralogical and geochemical features of diamond-bearing tourmaline crystals (schorl-uvite series) from garnet-clinopyroxene rocks of the Kumdy-Kol deposit (Northern Kazakhstan) have been studied in detail. The formation of the main rock-forming minerals (garnet + K-bearing clinopyroxene) occurred in the diamond stability field at 4-6 GPa and 950-1000 °C. Crystallization of K-bearing clinopyroxene at these parameters is possible in the presence of an ultra-potassic fluid or melt formed because of crustal material melting in subduction zones. Tourmaline crystals (up to 1 cm) containing diamond inclusions perform veins crosscutting high-pressure associations. The composition of individual zones varies from schorl to uvite within both a single grain and the sample as a whole. The potassium content in this tourmaline does not exceed 0.1 wt.% K2O, and the isotopic composition of boron δ11B varies from –10 to –15.5 ‰, which significantly differs from the previously established isotopic composition of boron in maruyamaite crystals (δ11B 7.7 ‰ in the core and –1.2 ‰ in the rim) of the same deposit. Analysis of the obtained data on δ11B in the tourmalines from the diamond-grade metamorphic rocks within the Kumdy-Kol deposit suggests the existence of two boron sources that resulted in crystallization of K-bearing tourmaline crystals (maruyamaite-dravite series) and potassium-free tourmalines of the schorl-uvite series.
-
Date submitted2022-10-26
-
Date accepted2023-02-13
-
Date published2023-07-19
Determination of the grid impedance in power consumption modes with harmonics
The paper investigates the harmonic impedance determination of the power supply system of a mining enterprise. This parameter is important when calculating modes with voltage distortions, since the determined parameters of harmonic currents and voltages significantly depend on its value, which allow the most accurate modeling of processes in the presence of distortions in voltage and current. The power supply system of subsurface mining is considered, which is characterized by a significant branching of the electrical network and the presence of powerful nonlinear loads leading to a decrease in the power quality at a production site. The modernization of the mining process, the integration of automated electrical drive systems, renewable energy sources, energy-saving technologies lead to an increase in the energy efficiency of production, but also to a decrease in the power quality, in particular, to an increase in the level of voltage harmonics. The problem of determining the grid harmonic impedance is solved in order to improve the quality of design and operation of power supply systems for mining enterprises, taking into account the peculiarities of their workload in the extraction of solid minerals by underground method. The paper considers the possibility of determining the grid impedance based on the measurement of non-characteristic harmonics generated by a special nonlinear load. A thyristor power controller based on phase regulation of the output voltage is considered as such a load. Simulation computer modeling and experimental studies on a laboratory test bench are used to confirm the proposed method. The recommendations for selecting load parameters and measuring device connection nodes have been developed.
-
Date submitted2021-09-02
-
Date accepted2022-01-24
-
Date published2022-04-29
Complex processing of high-carbon ash and slag waste
The paper considers a current issue of ash and slag processing for the Polyus Aldan JSC, that has accumulated over 1 million tons of this waste. Following the results of the review of Russian and foreign literature, four promising areas of their use were selected: road construction, building materials, reclamation of disturbed lands, and inert aggregates. To assess the possibility of implementing the selected disposal directions, the samples of ash and slag waste of the enterprise were sampled and analyzed. Fuel characteristics, chemical and mineral composition, as well as physico-chemical and mechanical properties of waste were determined. Taking into account the results of complex laboratory studies and the requirements of regulatory documents, each of the selected areas of using ash and slag waste was evaluated. It was found that their disposal by traditional methods has limitations, mainly related to the high content of unburned fuel residues. The high content of combustible substances and the high specific heat of combustion with a relatively low ash content suggested the possibility of thermal disposal of the studied waste. Based on the literature data, the characteristics of the preparation of organic coal-water suspensions based on the studied ash and slag waste were selected. As a result of a series of experiments on their flaring, the expediency of using the obtained fuel at the enterprise under consideration has been proved. The authors note the possibility of using ash obtained after thermal waste disposal in the road construction industry. The prospects for further research of technologies for the preparation and combustion modes of suspension fuel based on ash and slag waste are determined.
-
Date submitted2021-02-28
-
Date accepted2021-11-30
-
Date published2021-12-27
Substantiation of analytical dependences for hydraulic calculation of high-viscosity oil transportation
- Authors:
- Alexander K. Nikolaev
- Natalia А. Zaripova
One of the development priorities in oil and gas industry is to maintain gas and oil pipeline networks and develop pipeline-connected gas and oil fields of the Arctic zone of the Russian Federation, a promising region the resource potential of which will not only meet a significant portion of internal and external demand for various types of raw materials and primary energy carriers, but will also bring great economic benefits to subsoil users and the state. The mineral and raw material centers of the Nadym-Purskiy and Pur-Tazovskskiy oil and gas bearing areas are among the most attractive regions of the Arctic zone. It is necessary to develop a scientifically substantiated approach to improve the methods of oil transportation from the field to the existing pipelines. As it is known, the task of increasing the efficiency of pipeline transportation of high-viscosity oil is inseparably connected with solving problems in the field of thermal and hydraulic calculation of pipeline system. The article presents the substantiation of dependencies for hydraulic calculation of pipelines transporting high-viscosity oil exhibiting complex rheological properties. Based on the laws of hydraulics for non-Newtonian fluids, the formulas for calculating head losses for fluids obeying Ostwald's law are proposed, their relationship to the classical equations of hydraulics is shown. The theoretical substantiation of looping installation for increasing the efficiency of pipeline transportation of high-viscosity oil taking into account the received dependences for power fluid is considered.
-
Date submitted2021-03-11
-
Date accepted2021-07-27
-
Date published2021-10-21
Justification of a comprehensive technology for preventing the formation of asphalt-resin-paraffin deposits during the production of highlyparaffinic oil by electric submersible pumps from multiformation deposits
Production of highly solidifying abnormal oils (with a paraffin content of over 30 % by mass) in the Far North is complicated by the intensive formation of asphalt-resin-paraffin deposits (ARPD) in the bottomhole zone of the productive formation, well and surface equipment. Existing methods and technologies for countering the formation of organic deposits in well equipment have many advantages. However, their application in the production of highly paraffinic oil does not fully prevent the formation of ARPD in the tubing string. This leads to a significant reduction in oil production, reduction of turnaround and intertreatment periods of production wells operation, an increase in specific operating expenses for paraffin removal. Results of theoretical and laboratory investigations presented in the article show that one of the promising ways to improve the operational efficiency of wells equipped with electric submersible pumps during extraction of highly paraffinic oil from multiformation deposits is the application of a new integrated technology based on the joint production of highly solidifying abnormal oil with oil, characterized by a lower paraffin content and manifestation of structural and mechanical properties, in conjunction with the regulation of the parameters for the electric submersible pump. Results of numerical modeling using the PIPESIM steady-state multiphase flow simulator, physical, chemical and rheological investigations show that with a decrease of highly paraffinic oil from the productive formation D2ef in a blend with Stary Oskol oil from the Kyrtaelskoye field, a decrease in the mass content of paraffin in the blend and the temperature of its saturation with paraffin, depth and intensity of the organic deposits formation in the tubing string, pour point, as well as the improvement of the rheological properties of the investigated structured dispersed systems is observed. Article describes a promising assembly of well equipment for the single tubing separate production of highly paraffinic oil from multiformation deposits of the Timan-Pechora province, providing separation of the perforation zones in two productive formations using a packer-anchor system at simultaneous-separate operation of the formations by a double electric submersible pump unit.
-
Date submitted2020-08-20
-
Date accepted2021-04-01
-
Date published2021-06-24
Features of the mineral and chemical composition of the Northwest manganese ore occurrence in the Highveld region, South Africa
- Authors:
- Aleksandr N. Evdokimov
- Benedict L. Pharoe
The Northwest manganese ore mineralisation is located at a relative distance from traditionally known manganese mining areas in a new manganese-bearing region (Highveld) in the Northwest Province, Republic of South Africa. The ore occurrence was studied on farms: Buchansvale 61 IQ, Weltevreden 517 JQ, Rhenosterhoek 343 JP and Kafferskraal 306 JP. The data obtained from studying the geology of the area pointed out to interests regarding the development criterias for search of similar ore mineralisations in the northwest region of South Africa. The ore occurs predominantly in the form of powdered manganese wad, manganese nodules and crusts, confined to the karstic structures of the upper section of the dolomites. X-ray powder diffraction (XRD), Scanning electron microscopy with energy dispersive link (SEM-EDS) and X-ray fluorescence were utilized to unveil the mineral and chemical composition of the ore samples. The present study therefore presents the results on both chemical and mineral composition of manganese ores, and their depth and longitudinal distribution. Karstic areas causing an increased local thickness of the ore body were identified. The geochemical and microspcopic study of the ores indicates their supergene nature. The main ore minerals includes cryptomelane, lithiophorite, purolusite, hollandite and romanechite associated with impurity components of Ba, Ce, Co, La, Cr, Zn and V.
-
Date submitted2021-01-20
-
Date accepted2021-03-15
-
Date published2021-04-26
Improving the quality of electricity in the power supply systems of the mineral resource complex with hybrid filter-compensating devices
- Authors:
- Yurii A. Sychev
- Roman Yu. Zimin
The urgency and necessity of choosing and justifying the structures of hybrid filter-compensating devices based on series and parallel active filters to improve the quality of electricity in the power supply systems of enterprises of the mineral resource complex is shown. Mathematical models of hybrid filter compensating devices based on parallel and series active filters have been developed. Based on these mathematical models, computer simulation models of the indicated hybrid structures have been developed. The results of simulation showed the effectiveness of the correction of power quality indicators in terms of reducing the level of higher harmonics of current and voltage, as well as voltage deviations. The degree of influence of filter-compensating devices on the power quality indicators, which determine the continuity and stability of the technological process at the enterprises of the mineral resource complex, have been revealed. It has been established that a hybrid filter-compensating device based on a parallel active filter can reduce the level of higher harmonics of current and voltage by more than 90 and 70 %, respectively, and based on a series active filter, it can reduce the level of higher harmonics of voltage by more than 80 %. Based on the simulation results, the possibility of compensating for the reactive power of a hybrid structure based on parallel active and passive filters has been revealed. The possibility of integrating hybrid filter-compensating devices into more complex multifunctional electrical systems for the automated improvement of the quality of electricity is substantiated, as well as the expediency and prospects of their use in combined power supply systems based on the parallel operation of centralized and autonomous sources of distributed generation.
-
Date submitted2020-02-19
-
Date accepted2020-04-17
-
Date published2020-10-08
Decrease in coal losses during mining of contiguous seams in the near-bottom part at Vorkuta deposit
- Authors:
- Oleg I. Kazanin
- Valeriy V. Yaroshenko
The problem of formation of extended zones with high rock pressure (HRP) from safety pillars at the boundaries of extraction pillars formed due to the mine layout of complex geometry is considered at the example of JSC Vorkutaugol mines. A detailed analysis of the remaining reserves of the near-bottom part of the deposit was carried out to estimate losses and the impact of HRP zones from the Chetvertyi protective seam to mining operations on the Troinoi upper seam along with the possibilities for the reduction of sizes of HRP zones at the account of expanding the underworked space. Due to research on the near-bottom part of the Vorkuta deposit, within the framework of the accepted layout, a zone at the Komsomolskaya mine and two zones at the Zapolyarnaya-2 mine were singled out, at which losses at the boundaries of the extraction pillars amount up to 13-22 % of the total resources of the mine field. The high volume of losses in these pillars indicates the relevance of research on the priority extraction impact of protective seams on the efficiency and safety of mining operations in the working area of underworked and HRP zones. Based on the analysis of foreign and Russian experience in the pillar cleaning-up at the boundaries of working areas and the methodical guidelines and instructions, a technological scheme was developed that allows increasing the coal mining recovery factor in the near-bottom part of the Vorkuta deposit from 0.75 to 0.9 without fundamental changing of the ventilation and transport networks and also without purchasing any additional mining equipment. The conducted economic calculations confirmed the effectiveness of implementing the new technological scheme for cleaning-up reserves at the boundaries of extraction districts. The economic effect is from 0.079 to1.381 billion rubles of additional profit from coaxial extraction pillars, depending on the mining and geological conditions and the size of the pillars.
-
Date submitted2019-05-20
-
Date accepted2019-07-12
-
Date published2019-10-23
Development of Manufacturing Technology for High-Strength Hull Steel Reducing Production Cycle and Providing High-Quality Sheets
The article presents the results of scientific research and industrial experiments aimed at the development of technology to reduce the production cycle of high-strength hull steel. The technology includes an improved reduced heat treatment of ingots made using rare-earth metals and uphill teeming of large sheet ingots. The proposed technology for the preliminary heat treatment of ingots eliminates the high-temperature phase re- crystallization operation, which is unnecessary, according to the authors, since it does not allow partial crushing (grinding) of the metal dendritic structure and homogenization. When using the proposed technology of reduced pre- treatment, phase and structural stresses are sharply reduced. Experiments have shown that the modification of steel with rare-earth metals has a positive effect on the crystallization of ingots, changing the macro- and microstructure of alloy steel. The developed manufacturing technology of high-strength hull steel provides a high level of sheet quality and a reduction in the production cycle time by 10-12 %.
-
Date submitted2018-12-25
-
Date accepted2019-03-02
-
Date published2019-06-25
Non-linear electrical load location identification
- Authors:
- S. Pirog
- Ya. E. Shklyarskiy
- A. N. Skamyin
The article discusses the issues of identifying the location of non-linear loads in electrical networks which makes the main contribution to the distortion of the non-sinusoidal voltage and current in the distribution network of an industrial enterprise, including mining enterprises. The existing methods for determining the location of the source of higher harmonic components in voltage and current are considered, their advantages and disadvantages are revealed. The main disadvantages of the methods used include the low accuracy and incorrectness of their use in existing enterprises. When developing a new method, the authors were faced with the task of simplicity of its use in the conditions of industrial operation of electrical equipment and the absolute correctness of the results obtained. The proposed method of identifying the source of higher harmonics is based on the variation of the parameters of the power system, in particular, the change in resistance of power transformers taking into account their transformation ratio. It is shown that by varying the transformation ratio during regulation under load, the total coefficient of the harmonic components of the voltage changes. Based on the constructed dependencies, the variation of the derivative of this function with different variations of the parameters of sources of higher harmonics is analyzed and a method is developed that allows determining the share contribution of consumers to the total harmonic component of the voltage.
-
Date submitted2018-10-28
-
Date accepted2018-12-30
-
Date published2019-04-23
Development and research of formation technologies on specialized presses with subsequent sintering of high-density details from iron-based powders
- Authors:
- A. M. Dmitriev
- N. V. Korobov
- A. Zh. Badalyan
Creating shifts of the lyaers in a deforming workpieces improves the quality of the product produced by pressure treatment. qual-channel angular pressing and precipitations of a cylindrical billet with a rotating turnaround were developed by specialists earlier and became basic for scientists engaged in nanotechnology. One of the most modern schemes for creating nanostructures by processing on presses is the «Cyclic Extrusion Compression» scheme (in Russia – «Hourglass»), which has significant drawbacks. To date, research on the creation of layer shifts in compacted metal powders is substantially less than in compaction of compact blanks. The article developed compaction schemes for presses of blanks from iron-based powders that have a certain analogy with the «Hourglass», while lacking the disadvantages inherent in the named scheme and implemented on the created samples of specialized hydraulic presses. The results of the studies of density, strength and microhardness before sintering the samples molded from a number of domestic and imported powders on iron base, including those doped with carbon and other alloying components, are described. It has been established that with the use of the formation schemes for powders providing large shifts between particles, the density of the preforms increases on average by 10-12 %. With an average stress (16.32 MPa) of the transverse section of the molded specimen prior to its sintering, molding with shifts between particles increases this stress by 78 %. The strength after sintering of samples made using the compaction schemes developed by the authors of the article increases approximately by 2 times. Magnetic pulse treatment (MPT) of a molded sample prior to its sintering increases its resistance to shearing before sintering, regardless of the molding pattern. When MPT of both the powder and the molded sample is executed, the most uniform distribution of microhardness in the sample is achieved, and after subsequent sintering, the most uniform distribution of the mechanical characteristics of the product. The results of all studies are described by regression equations.
-
Date submitted2018-09-07
-
Date accepted2018-11-08
-
Date published2019-02-22
Assessment of refractory gold-bearing ores based on interpretation of thermal analysis data
- Authors:
- T. N. Aleksandrova
- G. Heide
- A. V. Afanasova
The article presents the results of a study on the possibility to assess refractory gold-bearing ores using thermal analysis data. It studies the flotation concentrates obtained during the enrichment of double refractory sulfide gold-bearing ores. This type of ore is complicated by the fine impregnation of gold in sulphide minerals and the presence of sorption-active scattered carbonaceous matter, which is in close association with sulphides. The results of thermogravimetric and mass spectrometric studies of refractory gold-bearing ores are presented. The obtained fragments for kerogen CH (m/z = 15), C 2 H (m/z = 29) and C 3 H (m/z = 43) indicate the presence of various types of carbonaceous matter in the studied samples. It is justified that the degree of sorption activity of carbonaceous matter depends on the presence of kerogen and bitumen in the ore. High sorption activity of scattered carbonaceous material significantly affects the processing technology of ores and concentrates, both flotation and pyro- and hydrometallurgical methods. Thermogravimetric and mass spectroscopic analyzes can be used to determine the degree of preg-robbing of refractory gold-bearing ores. The obtained results predetermine the direction of creating new methods and technologies in the field of decarburization of refractory gold-bearing ores in the integrated development of solid minerals in the mining regions of Russia.
-
Date submitted2018-05-06
-
Date accepted2018-07-17
-
Date published2018-10-24
Obtaining intermetallic compounds in Al–Ti–Zn system
- Authors:
- V. V. Kaminskii
- S. Y. Petrovich
- V. A. Lipin
Binary intermetallic compounds – titanium aluminides (TiAl, Ti 3 Al) – when added to the alloys, significantly increase their strength and special properties. The most promising direction to produce intermetallic compounds are mechanochemical technologies, including mechanical alloy building. Mechanical alloying makes it possible to introduce much smaller particles into the metal matrix than can be achieved using standard powder metallurgy technologies. In addition to mechanical synthesis, aluminum-based intermetallic compounds were produced by self-propagating high-temperature synthesis (SHS) of solid chemical compounds. The synthesis was carried out according to a multistage scheme: preparation of titanium and aluminum powder, mixing; synthesis of the Al 3 Ti intermetallic compound by the SHS method in vacuum followed by mechanical activation of stoichiometric charges. The aim of the research was to study the dynamics of the development of nanodispersed phases in the process of synthesis during mechanical alloying. The power absorbed by the unit mass of the material for different processing times of the charge was calculated. When the level of the specific power (dose) of mechanical treatment was 3.5 kJ/g, the maximum content of intermetallic compound in the resulting material was achieved. Based on calculations and the data obtained during X-ray phase analysis, the dependence of the change in the content of ternary intermetallic compounds in the final product on the absorbed power was determined. As a result of the studies using raster electron microscopy and X-ray analysis, it was found that mechanical alloying of nanostructured intermetallic compounds Ti 4 ZnAl 11 and Ti 25 Zn 9 Al 66 with the size of nanodisperse phases less than 12 nm in the Al–Ti–Zn system, the weight ratio of proportion of the latter reaches 74 %.
-
Date submitted2017-12-29
-
Date accepted2018-03-26
-
Date published2018-06-22
Methods to enhance oil recovery in the process of complex field development of the Yarega oil and titanium deposit
- Authors:
- I. E. Dolgii
Yarega oil and titanium deposit is a unique facility due to a combination of two mineral resources – oil and titanium ore – in one geologic structure. The paper describes mining and geologic conditions of the field, as well as engineering solutions to enhance oil recovery and the efficiency of heat transfer. The author focuses on the issues of deposit opening and preparation for development, and provides recommendations regarding the exploitation procedure of the oil and titanium parts of the field, which take into account field data on the extraction rates of high viscosity oil and titanium ore from the start of deposit development. The paper contains analysis of existing technological schemes of high viscosity oil extraction and steam heating of the oil bed, as well as assessment of their feasibility. Issues of field preparation for development are reviewed from the position of accumulated practical experience, and recommendations on the feasibility of combined underground and open-pit mining are supported with evidence. The main advantages of the proposed system are explained; key technical and economic indicators are calculated.
-
Date submitted2017-10-31
-
Date accepted2018-01-01
-
Date published2018-04-24
Peculiarities of formation and growth of nanodispersed intermetallic strengthening inclusions in rapidly-solidified alloys of Al–Mg–Zr–X-system
- Authors:
- D. I. Budelovskii
- S. Yu. Petrovich
- V. A. Lipin
The paper is devoted to the influence of the fourth element on the microstructure of the rapidly-solidified alloys of the Al–Mg–Zr-system. Alloys were additionally doped with high-melting-point metals Ti, Hf, W, and Nb. In the structure of all samples in the immediate area of the cooled surface, uniformly distributed intermetallic inclusions of several nanometers in size were detected. Such a structure can be represented as a dispersion-strengthened composite. A quantitative metallographic analysis was carried out to quantitatively describe the structure of the obtained particles of the cooled melt. The obtained rapidly-solidified alloys can be described as dispersion-strengthened composite materials with the aluminum-magnesium alloy matrix and the intermetallic particles strengthener. Depending on the alloying component, these particles differ in shape (spheres, plates, agglomerates) and in size (from 200 nm when alloying with Hf and W up to 1.2-1.5 μm with Ti and Nb alloying). The X-ray phase analysis (XPA) showed that in the studied alloys of the Al–5Mg–1.2Zr–(0.5÷2.0)X-system, high cooling rates of melts lead to the formation of new intermetallic compounds that are absent in equilibrium systems. The example of an alloy with hafnium additive shows that an increase in the content of the alloying component (from 0.5 to 2 % by mass) leads to an increase in the volume ratio of intermetallic inclusions (from 5 to 12.8 %). At the same time, their shape and average size remain unchanged. The additional alloying component will improve the mechanical characteristics of aluminum alloys by increasing the recrystallization threshold of a rapidly-solidified alloy.
-
Date submitted2017-08-26
-
Date accepted2017-11-10
-
Date published2018-02-22
On enhancement of cooperation between universities for implementation of the program «Sustainable development–2030»
- Authors:
- P. Ochirbat
- B. Chinzorig
The article is focused on one of the pressing issues of our time – the international training of qualified personnel in higher education institutions with the aim of developing a stable economic system of the state, the main elements of which are interrelated stages of economic activity (exploration, prospecting, extraction, processing, and use of mineral resources). The question of the contribution and role of universities of different countries cooperating in the sphere of sustainable development of this sector is considered. The necessity of practical solution of this task for the implementation of UNESCO's program «Sustainable Development – 2030» is determined. In this relation, the concept of «sustainable development», its philosophical, scientific-theoretical and cultural aspects are considered, the special significance of the connection between the sustainable development of society and its individual fragments with modern education is emphasized. It is stated that education, in the context of sustainable development, should be anticipating, advancing and open. Given the current trends in higher education, it is possible to mention the work carried out by the Mining Institute of the Mongolian State University of Science and Technology in the direction of international cooperation.
-
Date submitted2015-10-14
-
Date accepted2015-12-18
-
Date published2016-08-22
Complex utilization of treatment wastes from thermal power plants
- Authors:
- A. N. Shabarov
- N. V. Nikolaeva
The paper investigates present-day challenges related to accumulation, processing and disposal of the coal combustion wastes. The analysis of technogenic materials beneficiation practices using gravitation, magnetic and flotation beneficiation methods has been carried out. Quantitative and qualitative microscopic analysis of materials has been conducted. The study target were ash and slag wastes (ASW) from thermal power plant and coal combustion ash. Most metals are contained in coals and coal ashes in fine-dispersed (1-10 μm) mineral form. Various native metals and intermetallic compounds, sulfides, carbonates, sulfates, tungstates, silicates, rare earths phosphates and niobates have been discovered. Each metal may occur in several mineral phases, for instance tungsten may be in the form of wolframite, stolzite, ferberite, scheelite and represented by impurities. Not only composition of compounds is diversified, but also morphology of grains: well-defined and skeleton crystals, aggregates and polycrystalline structures, crystal twins and fragments; druses, globules and microspherules; porous shapes, flocculous and splintery clusters, lumpy aggregations, etc. Based on chemical silicate analysis of main ASW components the petrochemical properties of material have been assessed. Preliminary analyses have shown that concentration of ferrum-bearing components in ASW is around 5-11 %. The magnetic method of technogenic waste beneficiation with the help of high-gradient magnetic separation has been studied. The obtained evidences show that fine ASW are most efficiently separated in separators with high-gradient magnetic system. The studies provided justification of a process flow for complex treatment of technogenic carbon-containing material, including flotation, gravitation separation, magnetic heteroflocculation enrichment and high-gradient magnetic separation. The determined complex utilization ratio has proven the efficiency of complex processing.
-
Date submitted2015-08-25
-
Date accepted2015-10-24
-
Date published2016-04-22
The modern technology of drilling and casing of well during the exploration of gas hydrates
- Authors:
- N. I. Nikolaev
- Lyu Tyanle
In the paper, the perspectives of exploration and completion of gas hydrate fields and the drilling problems in the gas hydrates of the northwest china are studied. It has been established, that the main reasons of complications in the Muli field are the secondary hydrate formation on the walls of the well and drilling assembly and ice formation inside the set cement during the well drilling and completion in permafrost. It has been shown, that in the areas with permafrost during the drilling of the layers containing gas hydrates, temperature and pressure changes can lead to the dissociation of hydrates. At the same time, pressure increase in the annular space due to the gas release, can lead to the secondary formation of gas hydrates, drill string stuck, ceasing of drilling fluid circulation, which is the reason of serious trouble in the wellbore. The results of the research on the development of drilling fluids compositions, which lower the drilling troubles of permafrost, are presented. Comparative experiments have been conducted to evaluate the effectiveness of thermodynamic and kinetic inhibitors, which prevent the repeated hydrate formation. It has been established, that the kinetic inhibitors have the clear advantage: they have good inhibiting effects even with low amounts of additives. In the laboratory conditions, the researches have been conducted to evaluate the phase equilibrium of gas hydrates during their reaction with the water solutions, containing kinetic inhibitor PVP. A thin clay drilling mud has been developed on the water base, providing the holding of the temperature in the level of –2 °С and its effectiveness for the gas hydrate fields in the PRC has been shown. Casing effectiveness of unstable rocks during the drilling in the conditions of negative temperatures inside the well largely depends on their physical-mechanical properties, composition and the technical indicators of cement materials. The authors suggest the composition of quick-setting cements based on aluminum binding materials. It has been established, that the analyzed compositions have the ability to considerably improve the results of cementing.
-
Date submitted2015-07-14
-
Date accepted2015-09-28
-
Date published2016-02-24
Selection of rational heating temperature for pipeline pumping high-viscosity and high pour point crude oil
- Authors:
- A. K. Nikolaev
- V. I. Klimko
The article deals with the transportation problems of high-viscosity and high pour point crude oil through pipelines. The possibility of a structural oil movement mode development during transportation below the pour point is analyzed. The results of the experiment for unevenness of the heat flux identification in the underground pipeline are given.
-
Date submitted2015-07-11
-
Date accepted2015-09-17
-
Date published2016-02-24
The mechanism of rock burst leading to ground destruction of mine openings
- Authors:
- M. G. Mustafin
The article deals with the main issues of studying of one type of rock bursts which lead to gound destruction of coal mine openings. The research is focused on rock burst prediction. Some cases of rock bursts are analised. The paper points out factors affecting this kind of rock failure. It also presents some simulation models and numerical examples. The results of the research show that it is possible to plan safe mining operations under different mining and geological conditions.
-
Date submitted2014-12-28
-
Date accepted2015-02-21
-
Date published2015-12-25
Modeling of rock massif geomechanical state at gas extraction from coal seams
- Authors:
- M. G. Mustafin
The article describes the method of modeling a coal seam stress-strain state and an enclosing rock massif when degasified. An approach to defining the model input parameters, calculated with the porosity and gas pore pressure coefficient, was shown. The importance of preliminary calculations, indicating possible coal seam shrinkage and surface subsidence was underlined. It shows formation mechanism for coal seam zones with elevated gas pressure, where gas recovery is efficient.