-
Date submitted2023-04-10
-
Date accepted2024-11-07
-
Date published2025-02-25
Consideration of the geomechanical state of a fractured porous reservoir in reservoir simulation modelling
This paper presents reservoir simulation modeling of a hydrocarbon accumulation with a fractured porous reservoir, incorporating the geomechanical effects of fracture closure during variations in formation pressure. The fracture permeability parameter is derived from the impact of stress on fracture walls. The fracturing parameter is determined based on 3D seismic data analysis. A permeability reduction model is implemented in the tNavigator reservoir simulation platform. The proposed approach improves the convergence of formation pressure dynamics in well data while maintaining flow rate and water cut adaptation accuracy. This results in enhanced formation pressure prediction and optimization of the pressure maintenance system.
-
Date submitted2024-04-16
-
Date accepted2024-06-03
-
Date published2024-07-04
Quantitative determination of sulfur forms in bottom sediments for rapid assessment of the industrial facilities impact on aquatic ecosystems
- Authors:
- Ivan P. Sverchkov
- Vladimir G. Povarov
The article describes an X-ray fluorescence method for quantitative analysis of sulfate and total sulfur in bottom sediments of watercourses and reservoirs located in the area of industrial enterprises impact. The quantitative determination of sulfur forms was carried out by analyzing the characteristic curves SKα1,2 and SKβ1,3, as well as the satellite line SKβ′ on X-ray emission spectra measured by an X-ray fluorescence spectrometer with wavelength dispersion. The study shows that these characteristic curves allow not only to determine the predominant form of sulfur, but also to separately conduct quantitative analyses of sulfates and total sulfur after fitting peaks and to separately analyze overlapping spectral lines. The results of quantitative analysis of the chemical state of sulfur by the proposed X-ray fluorescence method were compared with the results of inductively coupled plasma atomic emission spectroscopy and elemental analysis, as well as certified standard samples of soils and sediments. The results are in good agreement with each other.
-
Date submitted2023-03-14
-
Date accepted2023-10-25
-
Date published2024-04-25
Predictive assessment of ore dilution in mining thin steeply dipping deposits by a system of sublevel drifts
The purpose of research is the study of stress-strain state of marginal rock mass around the stope and predictive assessment of ore dilution with regard for changes in ore body thickness in mining thin ore deposits on the example of the Zholymbet mine. Study of the specific features of the stress-strain state development was accomplished applying the methodology based on numerical research methods taking into account the geological strength index (GSI) which allows considering the structural features of rocks, fracturing, lithology, water content and other strength indicators, due to which there is a correct transition from the rock sample strength to the rock mass strength. The results of numerical analysis of the stress-strain state of the marginal part of the rock mass using the finite element method after the Hoek – Brown strength criterion made it possible to assess the geomechanical state in the marginal mass provided there are changes in ore body thickness and to predict the volume of ore dilution. It was ascertained that when mining thin ore deposits, the predicted value of ore dilution is influenced by the ore body thickness and the GSI. The dependence of changes in ore dilution values on the GSI was recorded taking into account changes in ore body thickness from 1 to 3 m. Analysis of the research results showed that the predicted dimensions of rock failure zone around the stopes are quite large, due to which the indicators of the estimated ore dilution are not attained. There is a need to reduce the seismic impact of the blasting force on the marginal rock mass and update the blasting chart.
-
Date submitted2023-01-16
-
Date accepted2023-06-20
-
Date published2024-04-25
Study on the thin layer drying and diffusion mechanism of low rank coal in Inner Mongolia and Yunnan
Coal is one of the world's most important energy substances. China is rich in coal resources, accounting for more than 90 % of all ascertained fossil energy reserves. The consumption share of coal energy reaches 56.5 % in 2021. Due to the high moisture content of low-rank coal, it is easy to cause equipment blockage in the dry sorting process. This paper considers low-rank coal coming from Inner Mongolia (NM samples) and Yunnan (YN samples). The weight loss performance of the samples was analyzed using thermogravimetric experiments to determine the appropriate temperature for drying experiments. Thin-layer drying experiments were carried out at different temperature conditions. The drying characteristics of low-rank coal were that the higher the drying temperature, the shorter the drying completion time; the smaller the particle size, the shorter the drying completion time. The effective moisture diffusion coefficient was fitted using the Arrhenius equation. The effective water diffusion coefficient of NM samples was 5.07·10–11 - 9.58·10–11 m2/s. The effective water diffusion coefficients of the three different particle sizes of YN samples were 1.89·10–11 - 4.92·10–11 (–1 mm), 1.38·10–10 - 4.13·10–10 (1-3 mm), 5.26·10–10 - 1.49·10–9 (3-6 mm). The activation energy of Inner Mongolia lignite was 10.97 kJ/mol (–1 mm). The activation energies of Yunnan lignite with different particle sizes were 17.97 kJ/mol (–1 mm), 33.52 kJ/mol (1-3 mm), and 38.64 kJ/mol (3-6 mm). The drying process was simulated using empirical and semi-empirical formulas. The optimal model for Inner Mongolia samples was the Two-term diffusion model, and Yunnan samples were the Hii equation was used.
-
Date submitted2023-04-02
-
Date accepted2023-06-20
-
Date published2023-07-19
Integration of renewable energy at coal mining enterprises: problems and prospects
This article addresses the issue of developing renewable energy in coal mining enterprises in the Russian Federation. The study presents a methodology for assessing the technical and economic efficiency of introducing renewable energy sources based on simulation modeling. An analysis of the potential of solar and wind energy for coal mining regions in Russia is conducted. The authors use a custom software developed by them to simulate the power supply system for various scenarios of renewable energy integration, including solar generation, wind generation, solar generation with energy storage, wind generation together with solar generation. Based on the example of the Rostov region, a feasibility study of the considered options is presented. Additionally, the research includes a sensitivity analysis of the investment project in the conditions of uncertainty in the development of Russian renewable energy. The research findings indicate that even in market conditions with CO2 emission quotas and prices at the level of the Sakhalin experiment, renewable energy in coal mining enterprises in Russia remains unattractive and requires additional support.
-
Date submitted2022-04-13
-
Date accepted2023-02-15
-
Date published2023-08-28
The impact of secondary mineral formation on Na-K-geothermometer readings: a case study for the Valley of Geysers hydrothermal system (Kronotsky State Nature Biosphere Reserve, Kamchatka)
The temperature in the Valley of Geysers (Kamchatka) geothermal reservoir calculated using the feldspar Na-K-geothermometer has been steadily increasing over the past 10 years on average from 165 to 235 °C, which is close to the temperature values of a hydrothermal explosion of the steam and water mixture. For the analysis of chemical geothermometers, TOUGHREACT-simulation was used, with the help of which the previously known Na-K feldspar geothermometer was reproduced on a single-element model and new formulas were obtained for three Na-K geothermometers: zeolite, smectite, and based on volcanic glass. Data of chemical analysis for the period 1968-2018, in which the chloride ion is considered as an inert tracer of geofiltration processes, indicates that after 2007 a significant inflow of infiltration water (its mass fraction is estimated from 5 to 15 %) into the Geyser reservoir. It is assumed that the Na-K increased values of the feldspar geothermometer are not the result of the temperature increase in the Geyser reservoir, but the effect of smectite water dilution.
-
Date submitted2022-06-20
-
Date accepted2023-01-10
-
Date published2023-08-28
Laboratory, numerical and field assessment of the effectiveness of cyclic geomechanical treatment on a tournaisian carbonate reservoir
Results are discussed for evaluation of effectiveness of the cyclic geomechanical treatment (CGT) on a Tournaisian carbonate reservoir. Analysis of laboratory experiments performed according to a special program to assess permeability changes for Tournaisian samples under cyclic changes in pore pressure is presented. The main conclusion is the positive selectivity of the CGT: an increase in permeability is observed for samples saturated with hydrocarbons (kerosene) with connate water, and maximal effect is related to the tightest samples. For water-saturated samples, the permeability decreases after the CGT. Thus, the CGT improves the drainage conditions for tight oil-saturated intervals. It is also confirmed that the CGT reduces the fracturing pressure in carbonate reservoirs. Using flow simulations on detailed sector models taking into account the results of laboratory experiments, a possible increase in well productivity index after CGT with different amplitudes of pressure variation was estimated. Results of a pilot CGT study on a well operating a Tournaisian carbonate reservoir are presented, including the interpretation of production logging and well testing. The increase in the well productivity index is estimated at 44-49 % for liquid and at 21-26 % for oil, with a more uniform inflow profile after the treatment. The results of the field experiment confirm the conclusions about the mechanisms and features of the CGT obtained from laboratory studies and flow simulations.
-
Date submitted2021-12-21
-
Date accepted2022-06-20
-
Date published2022-11-10
Scientific justification of the perforation methods for Famennian deposits in the southeast of the Perm Region based on geomechanical modelling
The article presents the results of analysing geological structure of the Famennian deposits (Devonian) in the Perm Region. Numerical modelling of the distribution of inhomogeneous stress field near the well was performed for the two considered types of perforation. With regard for the geometry of the forming perforation channels, numerical finite element models of near-wellbore zones were created considering slotted and cumulative perforation. It is ascertained that in the course of slotted perforation, conditions are created for a significant restoration of effective stresses and, as a result, restoration of reservoir rock permeability. Stress recovery area lies near the well within a radius equal to the length of the slots, and depends on the drawdown, with its increase, the area decreases. From the assessment of failure areas, it was found that in case of slotted perforation, the reservoir in near-wellbore zone remains stable, and failure zones can appear only at drawdowns of 10 MPa and more. The opposite situation was recorded for cumulative perforation; failure zones near the holes appear even at a drawdown of 2 MPa. In general, the analysis of results of numerical simulation of the stress state for two simulated types of perforation suggests that slotted perforation is more efficient than cumulative perforation. At the same time, the final conclusion could be drawn after determining the patterns of changes in permeability of the considered rocks under the influence of changing effective stresses and performing calculations of well flow rates after making the considered types of perforation channels.
-
Date submitted2022-06-20
-
Date accepted2022-10-10
-
Date published2022-11-03
Monitoring of grinding condition in drum mills based on resulting shaft torque
Grinding is the most energy-intensive process among all stages of raw material preparation and determines the course of subsequent ore beneficiation stages. Level of electricity consumption is determined in accordance with load characteristics forming as a result of ore destruction in the mill. Mill drum speed is one of process variables due to which it is possible to control ore destruction mechanisms when choosing speed operation mode of adjustable electric mill drive. This study on increasing energy efficiency due to using mill electric drive is based on integrated modelling of process equipment – grinding process and electromechanic equipment – electric drive of grinding process. Evaluating load torque by means of its decomposition into a spectrum, mill condition is identified by changing signs of frequency components of torque spectrum; and when studying electromagnetic torque of electric drive, grinding process is monitored. Evaluation and selection of efficient operation mode of electric drive is based on the obtained spectrum of electromagnetic torque. Research results showed that with increasing mill drum speed – increasing impact energy, load torque values are comparable for the assigned simulation parameters. From the spectra obtained, it is possible to identify mill load condition – speed and fill level. This approach allows evaluating the impact of changes in process variables of grinding process on parameters of electromechanical system. Changing speed operation mode will increase grinding productivity by reducing the time of ore grinding and will not lead to growth of energy consumption. Integration of digital models of the technological process and automated electric drive system allows forming the basis for developing integrated methods of monitoring and evaluation of energy efficiency of the entire technological chain of ore beneficiation.
-
Date submitted2020-05-13
-
Date accepted2021-05-21
-
Date published2021-09-20
Increasing the efficiency of technological preparation for the production of the manufacture components equipment for the mineral resource complex
An increase of components production for the equipment intended for oil and gas production is a key factor for analyzing existing technological processes and searching for new technological solutions to improve the efficiency of the production process and the quality of components. The article presents a simulation model designed to determine the rational technological processing parameters for the production of the “Centralizer shell” part. The basis for optimizing the working cycle of a production line is synchronization based on the principle of proportionality, which involves equalizing the duration of all technological operations with the rhythm of the production line. Synchronization of technological operations on the production line is carried out by choosing rational cutting parameters for each technological transition (cutting speed, feedrate, number of working passes). The “Centralizer shell” part is made of titanium alloy VT16, which has high strength, corrosion resistance and ductility. For the part under consideration, the permissible values of the cutting parameters were determined based on the calculation of the total processing error, as well as the frequency of replacement of the worn cutting tool. The simulation model described in the article made it possible to increase the efficiency of the production process due to the synchronization of technological operations and the search for rational technological parameters, as well as to improve the manufacturing quality of the “Centralizer shell” part by analyzing the processing error at various parameters of the technological process.
-
Date submitted2020-07-22
-
Date accepted2020-11-12
-
Date published2020-12-29
Simulation of the electric drive of the shearer to assess the energy efficiency indicators of the power supply system
- Authors:
- Vyacheslav A. Voronin
- Fedor S. Nepsha
This paper considers the problem of electric drive of shearers simulation to assess the indicators of power supply system (PSS) energy efficiency in the context of the introduction of modern devices for controlling the flow of electricity and power. The block diagram of the shearer electric drive simulation model is presented. To take into account fluctuations in the level of consumption of active and reactive power, a model of the executive body of the shearer was used in the work, including a model of the moment of resistance on the auger when cutting. As a result, in the MATLAB Simulink environment, a simulation model of the electric drive of the UKD300 shearer was developed, suitable for assessing the energy efficiency of the electrical complex of mining areas and the feasibility of using modern devices for controlling the flow of electricity and power. As a result of the simulation, it was found that a significant irregularity in the graph of reactive power consumption, caused by repeated short-term operation, makes the use of capacitor units ineffective to compensate for reactive power.
-
Date submitted2019-07-06
-
Date accepted2019-08-25
-
Date published2019-12-24
Improving the efficiency of technological preparation of single and small batch production based on simulation modeling
Technological preparation of production is an integral stage of the production process, which is characterized by high complexity, which is largely felt in the conditions of single and small-scale types of production. The effectiveness of technological preparation of production is increased through automation with the use of simulation modeling. The objective of the study is to develop a simulation model that allows you to determine a rational version of the process for processing a batch of parts. The simulation model described in the article allows to analyze the production schedule of the enterprise, build processing routes, evaluate options for using various types of workpieces and technological equipment, determine the acceptable values of cutting conditions, and choose a rational variant of the technological process of processing a batch of parts. The developed simulation model is based on the principles of modular technologies, the part is considered as a combination of individual elementary surfaces. Each elementary surface contains information about the technological processing route, technological equipment and the type of technological equipment used in its manufacture, cutting conditions and the size of the allowance for each processing stage. The rational choice of the technological process is selected on the basis of multicriteria analysis according to three criteria: the value of variable costs, the production time of a batch of parts and the value of the processing error. The analysis of these criteria is made and the parameters that have the greatest impact on their value are determined. The developed classification of surface elements is described: design elements, technological elements, basic elements, as well as a mathematical model based on which the calculation of the values of the criteria for choosing a rational option.
-
Date submitted2017-11-22
-
Date accepted2018-01-04
-
Date published2018-04-24
Justification of a methodical approach of aerologic evaluation of methane hazard in development workings at mines of Vietnam
- Authors:
- V. V. Smirnyakov
- Nguen Min' Fen
The methods of evaluation of the aerological conditions to be performed for the purpose of normalization of mining conditions are provided in the present review; the location of possible accumulations of explosive gases during the drift of the development workings are taken into account. To increase the safety of the development working regarding the gas factor, a complex evaluation of a working was developed with respect to the dynamics of methane emission and air coursing along the working which is strongly affected by the character of the leakages from the ventilation ducting. Thereby, there occurs a necessity of the enhancement of a methodical approach of calculation of ventilation of a working which consists in taking into consideration a total aerodynamic resistance of the booster fan including the local resistances of the zones of the working. An integer simulation of the gas-air flows realized on the basis of a software package FLowVision allows to evaluate a change in the methane concentration in the zones of local accumulations.
-
Date submitted2015-12-01
-
Date accepted2016-02-29
-
Date published2016-12-23
Simulation of diesel engine energy conversion processes
- Authors:
- A. S. Afanasev
- A. A. Tretyakov
In order to keep diesel engines in good working order the troubleshooting methods shall be improved. For their further improvement by parameters of associated processes a need has arisen to develop a diesel engine troubleshooting method based on time parameters of operating cycle. For such method to be developed a computational experiment involving simulation of diesel engine energy conversion processes has been carried out. The simulation was based on the basic mathematical model of reciprocating internal combustion engines, representing a closed system of equations and relationships. The said model has been supplemented with the engine torque dynamics taking into account the current values of in-cylinder processes with different amounts of fuel injected, including zero feed. The torque values obtained by the in-cylinder pressure conversion does not account for mechanical losses, which is why the base simulation program has been supplemented with calculations for the friction and pumping forces. In order to determine the indicator diagram of idle cylinder a transition to zero fuel feed mode and exclusion of the combustion process from calculation have been provisioned.
-
Date submitted2015-10-24
-
Date accepted2015-12-17
-
Date published2016-08-22
Spatial distribution of energy release during propagation of fast electron beam in the air
- Authors:
- V. S. Sukhomlinov
- A. S. Mustafaev
The paper focuses on development of the analytical theory to assess spatial distribution of energy released during propagation of the fast electron beam in a gas, in particular in the air at electron energies of 1-100 keV. An approach adopted by authors [2, 3] to study inelastic deceleration of electrons in the air is further developed here. As the inelastic interaction in most cases leads to energy relaxation while elastic interaction causes distribution isotropization over directions, the first task solved in the paper is finding the electron distribution function including only elastic collisions. In the final part of this paper an analytical solution to this task is presented with account of both types of electron deceleration in the air. The calculations show that when elastic collisions are taken into account this leads to increased spatial density of energy release and to narrowing of the primary energy release region of the fast electrons, as compared to calculations accounting for only inelastic deceleration.
-
Date submitted2015-08-18
-
Date accepted2015-10-06
-
Date published2016-04-22
Energy- efficient control of asynchronous motor drive with current refinement of the loss minimum on the basis of fuzzy logic
- Authors:
- O. B. Shonin
- V. S. Pronko
Currently, asynchronous electric drive on the basis of semiconductor frequency converters is widespread because of the relative simplicity and reliability of the design, the use of digital control systems, providing the accuracy and flexibility of process control, which allows for a significant increase in product quality, reduction in energy consumption and improvement of the enterprise profitability. In spite of these advantages, the problem of ensuring high energy efficiency of the drive in wide range of its operational modes is still not solved in full scale. The paper is devoted to the reduction of losses in the asynchronous drive on the basis of en-ergy-saving control algorithms that aim to ensure the desired mode of the driven mechanism while minimizing losses in copper and steel of the motor. On the basis of the motor model, taking into account magnetic losses, dependences of losses in the copper and steel, as well as the total loss from the absolute slip have been derived for different operating points of the drive. The optimal values of the absolute slip for different speeds of the rotor have been obtained for use in the con-trollers ensuring operation of the drive at maximum efficiency, highest power factor and minimum of the stator current. For minimizing the losses in the drive when changing the motor parameters it has been offered the combined method based on the method of loss model and iterative method of searching the minimum of power consumption. The effectiveness of the proposed control system using fuzzy logic is confirmed by comparing the graphs of losses and efficiency, obtained at using a traditional control law and the optimal control law.
-
Date submitted2015-07-11
-
Date accepted2015-09-17
-
Date published2016-02-24
The mechanism of rock burst leading to ground destruction of mine openings
- Authors:
- M. G. Mustafin
The article deals with the main issues of studying of one type of rock bursts which lead to gound destruction of coal mine openings. The research is focused on rock burst prediction. Some cases of rock bursts are analised. The paper points out factors affecting this kind of rock failure. It also presents some simulation models and numerical examples. The results of the research show that it is possible to plan safe mining operations under different mining and geological conditions.
-
Date submitted2010-07-17
-
Date accepted2010-09-02
-
Date published2011-03-21
Selection of parameters camouflet blasting to reduce bump hazard by development uranium deposits
- Authors:
- D. Yu. Dordzhiev
Simulation-based by the finite element values obtained stress strain state around the stope ore as ore body downstream horizontal layers with a mined-out space. The results of the simulation allowed to substantiate a contained blasting parameters to bring pillar to anti bump hazard state.
-
Date submitted2010-07-19
-
Date accepted2010-09-22
-
Date published2011-03-21
Simulation of swinging movement autoresonant electric drive with nonsymmetric excitation
- Authors:
- A. N. Fomenko
Mathematical and simulation models of drill bit oscillations. Method for calculating the model works elastic, electromagnetic and load torques has been developed. Simulation results of autoresonant regimes with asymmetric excitation oscillations of dynamically counter balanced drilling string on the cargo-carrying cable drill bit are represented.
-
Date submitted2010-07-01
-
Date accepted2010-09-12
-
Date published2011-03-21
Usage modern computer techniques for validation of actions guaranteeing opening strength of pit edge
- Authors:
- S. N. Kotlov
In this article is described an example of using program Modflow for the issues of oreation geofiltration processes numerical simulation on procedure of horizontal drainage well simulation. Also is estimated stability of pit edges in case of using system horizontal drains.
-
Date submitted2009-09-01
-
Date accepted2009-11-21
-
Date published2010-06-25
Mathematical simulation of emergency situations arising at storage and treatment of potential hazard chemical substances
- Authors:
- Yu. V. Sharikov
- I. N. Beloglazov
Possible reasons arising destroying of storage and apparatuses for potential hazard materials have been analyzed. Thermal explosion has been indicated as one of most impotent reasons of destroying chemical reactors and storages. Basic equations for describing of this phenomena have been evaluated for different type geometry and conditions of heat exchange on outside surface. Numerical procedures have been proposed and tested for solving and analyzing of evaluated equations with using special program package ThermEx. Processes of evaluation arising clouds of hazard substances have been considered. Basic mathematical equations have been proposed for analyze of considered processes. The procedure for solving of considered problems has been proposed and tested on base of special program package ReactOp.
-
Date submitted2009-07-06
-
Date accepted2009-09-18
-
Date published2010-04-22
Simulation of the stress-strain state forming around the vertical mine in the field of tectonically fractured massif
- Authors:
- D. Yu. Dordzhiev
The influence of the front clean up of stress-strain state around a vertical mine of a tectonically fracture massif for a uranium deposit «Antey» is considered. By means of computer simulation it’s have been confirmed by field observations.