-
Date submitted2023-09-05
-
Date accepted2024-11-07
-
Date published2025-02-25
Investigation of the accuracy of constructing digital elevation models of technogenic massifs based on satellite coordinate determinations
At all stages of the life cycle of buildings and structures, geodetic support is provided by electronic measuring instruments – a laser scanning system, unmanned aerial vehicles, and satellite equipment. In this context, a set of geospatial data is obtained that can be presented as a digital model. The relevance of this work is practical recommendations for constructing a local quasigeoid model and a digital elevation model (DEM) of a certain accuracy. A local quasigeoid model and a DEM were selected as the study objects. It is noted that a DEM is often produced for vast areas, and, therefore, it is necessary to build a local quasigeoid model for such models. The task of assessing the accuracy of constructing such models is considered; its solution will allow obtaining a better approximation to real data on preassigned sets of field materials. A general algorithm for creating both DEM and local quasigeoid models in the Golden Software Surfer is presented. The constructions were accomplished using spatial interpolation methods. When building a local quasigeoid model for an area project, the following methods were used: triangulation with linear interpolation (the least value of the root mean square error (RMSE) of interpolation was 0.003 m) and kriging (0.003 m). The least RMSE value for determining the heights by control points for an area project was obtained using the natural neighbour (0.004 m) and kriging (0.004 m) methods. To construct a local quasigeoid model for a linear project, the following methods were applied: kriging (0.006 m) and triangulation with linear interpolation (0.006 m). Construction of the digital elevation model resulted in the least aggregate value of the estimated parameters: on a flat plot of the earth’s surface – the natural neighbour method, for a mountainous plot with anthropogenic topography – the quadric kriging method, for a mountainous plot – quadric kriging.
-
Date submitted2024-01-31
-
Date accepted2024-06-03
-
Date published2024-07-04
Rationale for a possibility of using humic preparations production waste for wastewater purification from metals (Cd2+, Zn2+, Mg2+, Cu2+) aimed at developing efficient measures on environmental rehabilitation
Results of studying optimal conditions and parameters for afterpurification of underspoil waters from metal ions using humic acids production waste are presented with a view to develop the efficient measures on environmental rehabilitation of ecosystems disturbed by the development of copper pyrite deposits. The influence of contact time and waste dosage on the purification process was analysed, changes in the pH of wastewater and its impact on the growth and development of plants were studied. The key factors were identified allowing to achieve the efficiency of the purification process – the optimal contact time in the range from 120 to 180 min and waste dosage of 10 g/l. The study showed that the use of waste resulted in a neutral pH value of 7.03 compared to the initial pH value of 5.95. It was ascertained that the use of iron-magnesium production waste in combination with waste from humic preparations production made it possible to achieve the MPC of commercial fishing importance (with the exception of magnesium). Wastewater after the afterpurification process with high magnesium concentrations did not have a stimulating effect on the growth and development of Lepidium sativum L. plants. From biotesting results it can also be stated that there is no negative impact on the growth and development of Lepidium sativum L. The results obtained indicate a potentiality of using afterpurified wastewater for watering plants in the process of initiating the environmental rehabilitation of the disturbed ecosystems.
-
Date submitted2024-03-07
-
Date accepted2024-06-14
-
Date published2024-07-04
Anomaly detection in wastewater treatment process for cyber resilience risks evaluation
Timely detection and prevention of violations in the technological process of wastewater treatment caused by threats of different nature is a highly relevant research problem. Modern systems are equipped with a large number of technological sensors. Data from these sensors can be used to detect anomalies in the technological process. Their timely detection, prediction and processing ensures the continuity and fault tolerance of the technological process. The aim of the research is to improve the accuracy of detection of such anomalies. We propose a methodology for the identification and subsequent assessment of cyber resilience risks of the wastewater treatment process, which includes the distinctive procedure of training dataset generation and the anomaly detection based on deep learning methods. The availability of training datasets is a necessary condition for the efficient application of the proposed technology. A distinctive feature of the anomaly detection approach is a new method of processing input sensor data, which allows the use of computationally efficient analytical models with high accuracy of anomaly detection, and outperforms the efficiency of previously published methods.
-
Date submitted2023-05-19
-
Date accepted2024-03-05
-
Date published2024-08-26
Development and research of backfill compounds with improved elastic and strength properties for oil and gas well lining
This article describes operations from the well construction cycle where the cement rock behind the casing is subjected to dynamic action (impacts of the drill stem during drilling and normalization of the cement sleeve, secondary drilling operations, hydraulic fracturing, etc.). The developed cement mortar compositions were tested following API 10B-2, API 10B-6, API STD-65-2, and GOST 28985-91 standards. The composition of the cement system without the use of imported components (CM-5) was developed, which improved elastic and strength properties compared to existing industry solutions. An improvement in the elastic and strength features and technological properties of cement rock when using epoxy resins was identified, the optimal composition of the cement-and-epoxy grout was determined, and the internal structure of the formed backfill rock, its permeability, and porosity were studied.
-
Date submitted2022-05-20
-
Date accepted2023-04-03
-
Date published2024-02-29
Impact of carbon dioxide on the main geotechnical quality criteria and preparation cost of cemented paste backfill
There is a global upsurge in the use of cemented paste backfill (CPB) for various mining functions. However, the cost of the Portland cement binder is prohibitive, thus warranting strategies to reduce cement usage without overly diminishing the CPB quality. Since carbon dioxide is used for patented sand moulding processes, this study is premised on that physicochemical ability of CO2 to enhance the curing of consolidated inorganic materials. It evaluated the impact of carbon dioxide on the uniaxial compressive strength UCS and preparation cost of CPB standard samples (ASTM C109). The preparation cost was delimited to the purchase cost of the Portland cement. The backfill material was silica sand tailings with 4.5 wt.% Portland cement binder and a water-cement ratio of 7.6. Distilled water of pH 5.4 was used for the control samples while variable amounts of carbon dioxide were dissolved in distilled water to generate carbonated mixing water with pH values of 3.8; 4 and 4.2. The lower the carbonated water pH, the higher is the CO2 concentration. UCS tests were conducted on the samples after curing for 3, 7, 28, and 90 days. There was an observable increase in the UCSs and reduction in curing time with increasing carbon dioxide. Samples prepared with carbonated water of pH 3.8 had almost double the strength of those prepared with pure distilled water of pH 5.4, implying that more dissolved CO2 corresponds to higher CPB strength. This is supported by the trendline equations for the graphical simulation of strength on curing time. Thus, CPB with much less binder can be expected to attain the requisite UCS if carbon dioxide is incorporated. The average reduction in Portland cement consumption was 0.61 %, which translates to a cost saving of the same percentage points. If calculated over the operational life of a mine, this is a massive saving of millions of dollars.
-
Date submitted2022-05-25
-
Date accepted2023-02-02
-
Date published2023-08-28
Evaluation of the shear strength of rocks by cracks based on the results of testing samples with spherical indentors
Experimental data on the relationship of the residual shear strength of rocks in closed cracks with the functional characteristics of intact rocks – the tensile and compressive components of adhesion, the roughness of the crack surfaces, and the level of normal stresses are presented. A unified integrated approach determines the shear strength of intact and destroyed rocks, the residual shear strength of closed rough cracks has been developed. The approach provides for the selection of stress intervals corresponding to different types of fracture, for each of which a strength criterion is proposed, expressed in terms of functional characteristics of intact rock. An express method for estimating the residual shear strength of rocks by cracks with a rough surface has been developed, in which an improved method of loading samples with spherical indentors is used as a basic test method. The express method implements the transition from the data of mechanical tests of samples with spherical indentors to the shear strength indicators for cracks in the rock mass, taking into account the level of normal stresses and the roughness of the crack surfaces measured in field conditions. In this case the roughness scale developed by Barton is used. The express method is informative and available in the fieldwork.
-
Date submitted2021-02-24
-
Date accepted2022-04-06
-
Date published2022-07-13
Study of the kinetics of the process of producing pellets from red mud in a hydrogen flow
The reduction kinetics of serial phase transitions of iron oxides during reduction to a metallized state with different modes of technical hydrogen supply has been studied and substantiated. The results of the pellets formation when 3-5 % molasses is added to the red mud as a binding reagent are presented. The dependences of the reduction rate of iron oxides on the hydrogen flow rate are obtained. Based on the results of the experiments, a kinetic model was constructed, and with the help of X-ray phase and spectral analysis, it was proved that the agglomerates formed after heat treatment received high strength due to the adhesion of reduced iron particles with red mud particles. The use of a new type of charge materials in melting units will reduce the amount of emissions and dust fractions, as well as increase the metal yield.
-
Date submitted2021-08-10
-
Date accepted2021-12-10
-
Date published2021-12-27
Possibilities of accounting the fracturing of Kashiro-Vereyskian carbonate objects in planning of proppant hydraulic fracturing
One of the effective methods of oil production intensification for heterogeneous Kashiro-Vereyskian clay-carbonate sediments of the Volga-Ural oil and gas bearing province is proppant hydraulic fracturing. Prospects of realization for this technology are considered in the article on the example of the Vereyskian development object of Moskud’inskoye field. Based on the analysis of rocks samples investigations of Vereyiskian sediments, lithological types of carbonate rocks differing in their structural features are distinguished. Tomographic investigations of rock samples were carried out, as a result of which the rock fracturing for some lithotypes was determined and studieds. Under natural geological conditions, depending on the degree of fracturing progression and technological conditions of development, these intervals may or may not be involved in well operation. When hydraulic fracturing is performed, potentially fractured areas that are not in operation can be successfully added to oil production. Based on analysis of hydrodynamic well investigations, the fracturing of the Vereyskian object of the Moskud’inskoye field was studied on the basis of the Warren-Ruth model. With the help of geological and technological indicators of development, prediction fracturing was obtained, which was used for the construction of the natural fracturing scheme. Areas of both pore and fractured reservoirs development were identified on the deposit area. As a result of statistical analysis, the influence of fracturing on efficiency of proppant hydraulic fracturing was determined. Based on the linear discriminant analysis, a statistical model for predicting the efficiency of proppant fracturing was developed. It was shown that in addition to natural fracturing, the results are most strongly influenced by specific proppant yield, formation pressure, permeability of the remote bottomhole zone and skin effect. Based on the developed model, prospective production wells of the Moskud’inskoye field are identified for proppant hydraulic fracturing.
-
Date submitted2020-06-12
-
Date accepted2020-06-12
-
Date published2020-06-30
Management of hardening mixtures properties when stowing mining sites of ore deposits
Underground mining is characterized by the weakening of the bearing rock mass strata competence and the accumulation of mineral waste. The full use of subsurface resources is ensured by the use of technologies with filling voids by hardening mixtures, which requires high-quality raw materials to obtain the required strength. The deficit of the binding component can be filled with the use of granulated slags of blast-furnace process, mill tailings, ash-slags and other wastes. Most often, voids are laid by mixtures with a combination of cement and a binding component. Mixtures with ash-slag additives to cement in an equivalent amount are not inferior to the strength of the mixture only with cement, especially when grinding ash-slag. The properties of stowing rock masses when using composite binding components and inert fillers are controlled by mechanical, chemical, physical and energy effects at the stages of preparation and transportation of hardening mixtures. To obtain the active fraction of cement substitutes, disintegrators are used that apply the inertia forces of materials at a high speed of rotation with an increase in high activity indicators and lower energy costs. The components of hardening mixtures can be the majority of waste from mining and related industries, which is determined experimentally in specific conditions.
-
Date submitted2019-04-30
-
Date accepted2019-07-16
-
Date published2019-10-23
Salt Rock Deformation under Bulk Multiple-Stage Loading
- Authors:
- I. L. Pankov
- I. A. Morozov
The paper presents experimental justification of the possibility to use bulk multiple-stage loading to study the process of salt rock deformation in the laboratory conditions. Results of comparative tests between bulk multiple- stage and single-stage loading of salt rock samples are demonstrated. The paper contains results of research on the rate of lateral pressure and its impact on strength limit and residual strength limit of sylvinite, estimated using single- stage and multiple-stage methods. Research results demonstrate how the rate of lateral pressure impacts dilatancy boundary of salt rocks. Analysis of how the loading method influences certificate parameters of Mohr-Coulomb strength of sylvinite has been carried out. The dynamics of elastic modulus in the process of salt rock deformation is analyzed depending on the rate of lateralpressure. It is demonstrated how the method of multiple-stage loading adequately reflects the processes of salt rock de- formation and decomposition, and facilitates not only lowering impact of sample’s inner structure heterogeneities on the experimental results, but also significant reduction in the required amount of rock material.
-
Date submitted2019-04-27
-
Date accepted2019-07-10
-
Date published2019-10-23
Estimation of Rock Mass Strength in Open-Pit Mining
The paper presents results of an experimental study on strength characteristics of the rock mass as applied to the assessment of open-pit slope stability. Formulas have been obtained that describe a correlation between ultimate and residual strength of rock samples and residual shear strength along the weakening surface. A new method has been developed to calculate residual interface strength of the rock mass basing on data from the examination of small-scale monolith samples with opposing spherical indentors. A method has been proposed to estimate strength characteristics (structural weakening coefficients and internal friction angles) of the fractured near-slope rock mass. The method relies on test data from shattering small-scale monolith samples with spherical indentors, taking into ac- count contact conditions along the weakening surface, and can be applied in the field conditions. It is acceptable to use irregular-shaped samples in thetests.
-
Date submitted2018-07-21
-
Date accepted2018-09-14
-
Date published2018-12-21
Natural ventilation of gas space in reservoir with internal floating roof
- Authors:
- M. G. Karavaichenko
- N. M. Fathiev
The article deals with safe operation issues of vertical steel reservoirs with an internal floating roof when storing volatile oil products. The purpose of the work is to study the influence of ventilation openings area and wind speed on the duration of explosive state of vertical reservoirs with an internal floating roof. The influence of ventilation pipes' dimensions and the wind speed on the duration of explosive state of the reservoir has been studied. Method for calculating this time is proposed. It is shown that natural ventilation of the reservoir gas space is caused by the effect of two forces, which are formed due to: 1) the density difference between the vapor-air mixture in the reservoir and outside air; 2) wind pressure occurring on the roof of the reservoir. An algorithm for calculating the duration of reservoir being in an explosive state with wind pressure and no wind is obtained. The greater the difference in geodetic marks of the central and peripheral nozzles, the more efficient the ventilation. This distance will be greatest if the lower ventilation pipes are located on the upper belt of the reservoir or the reservoir is equipped with an air drain. Increase in wind speed of more than 10 m/s does not significantly affect the duration of the reservoir being in an explosive state. Increasing the diameter of the central nozzle from 200 to 500 mm can significantly reduce the duration of the reservoir degassing in windless weather.
-
Date submitted2017-11-17
-
Date accepted2018-01-05
-
Date published2018-04-24
Estimation of the relation of strength and ultrasound speed in glass-reinforce plastic
- Authors:
- A. I. Potapov
In mining machinery, details and products made of composite materials are widely used, especially from GRP (glass-reinforce plastic). The work evaluates the relationship between the strength and the speed of ultrasound for nondestructive testing of strength in an article made of composite materials such as GDR with the use of a pulsed ultrasonic method. Methods for estimating the connection, the method of mechanical compression tests and mathematical processing and establishing the relationship between the ultrasonic velocity and the strength of GRP are considered. The results of experimental studies on establishing the relationship between the strength of GRP on compression and the speed of longitudinal ultrasonic waves are presented. As a result of statistical processing of the experimental results, equations of the relationship between the compressive strength and the ultrasonic velocity in fiberglass are obtained.
-
Date submitted2017-09-20
-
Date accepted2017-10-29
-
Date published2018-02-22
Substantiation of strength of the filling mass by taking a blast effect into account for the room-and-pillar methods
- Authors:
- E. T. Voronov
- V. N. Tyupin
The development of the uranium ore bodies at the ore mines of PJSC «Priargunsky Industrial Mining and Chemical Union» (PJSC «PIMCU») by room-and-pillar method as high as a pillar between the levels (60 m) without fill, as a rule, leads to the fall of the adjoining rock, to the strong contamination of the ore and to the high yield of the oversize pieces of the barren rock. A longstanding industrial and theoretical research shows that the sizes of the self-sustaining rock escarpments at the ore mines of PJSC «PIMCU» in the solid mass of trachydacites, conglomerates, sandstones, felsites are equal to 20-40 m. Moreover, the sizes of the self-sustaining rock escarpments depend to a great extent on the intensity of fracturing of the adjoining rocks. The stable size of the escarpment does not exceed 5-10 m for the rocks with the size of a jointing up to 0.05 m. Consequently, timely performance of the filling operations of the worked-out space of the chamber is important. However, the question then arises: which characteristic strength should the filling mass have? The calculations of the characteristics of the filling mass in compliance with the reference guide «Shaft filling operations» show underestimated values of the characteristic compressive strength of the fill (1.4 MPa) for the room-and-pillar method, which leads to the increase of the ore contamination by the fill and provokes the additional costs for refilling of the volumes of the rock fall. On the basis of the Russian experience of using of the consolidated fill for the development of the ore bodies of 15 m thickness by chamber method the strength of the fill is taken as 3-5 MPa under the resultant value of the static stresses without taking into account the character of the dynamic loading stresses induced by the sequence blasthole ring initiating in a chamber. Overestimating the characteristic strength of the filling mass results in the high consumption of the cementing materials. On the basis of the theoretical research the authors suggested the theoretical dependence of calculation of the characteristic strength of the filling material with respect to compressive stresses of the fill induced by the blasting operations. The process of designing of the filling mass with the zones of diverse strength for the room-and-pillar extraction with the consolidated rock fill is proven to be economically reasonable. The bottom zone of the solid mass should have high strength (3-4 MPa), and the strength of the upper zone should be up to 2-2.5 MPa.
-
Date submitted2017-09-11
-
Date accepted2017-10-30
-
Date published2018-02-22
Provision of adhesion strength of gas-thermal coatings on piston rings of quarry transport engines
- Authors:
- Yu. Olt
- V. V. Maksarov
- V. A. Krasnyi
The main trend in the development of modern diesel engine manufacturign is the creation of high-powered, reliable and economical internal combustion engines (ICE), which are widely used in various industries, including mining machinery. The application of the methods of gas-thermal and gas-plasma coating for obtaining wear-resistant layers on piston rings for large internal combustion engines of quarry transport – diesel locomotives and dump trucks- is considered. It is shown that the abrasive-jet machining of base coat is widely used as a preparatory operation before coating process, and the roughness of the working surface of the rings after abrasive-jet machining has a significant impact on the adhesion strength of the coating with the base material. The selection of the surface roughness and the conditions of abrasive-jet machining for increasing the coating adhesion strength to the base coat significantly determines both the thickness of the coating and the reliability of the part itself. The aim of the paper is to investigate the dependence of the adhesion strength of a gas-thermal wear-resistant coating of piston rings of large engines of quarry transport, including dump trucks and diesel locomotives, from the roughness of the working surface after abrasive-jet machining, which in turn depends on its modes (distance to the nozzle exit section, the number of passes, the working air pressure, the shot change rate). The working surface adhesion strength of piston rings with diameter of 210 mm coated with molybdenum and steel wire composition was investigated by the twisting angle at which the coating peeled. It is shown that the roughness providing a twist angle greater than 35° should be more than 22 μm, which does not cause coating peeling off. Modes of abrasive-jet machining providing the specified values of roughness: working air pressure is 0.4 MPa, distance to the nozzle exit section is 110 mm, the number of passes is 2, and the shot changes after processing 40 mandrels.
-
Date submitted2016-11-14
-
Date accepted2017-01-09
-
Date published2017-04-14
Method of restoring strength determination test
- Authors:
- S. M. Apollonskii
- Yu. V. Kuklev
The main requirements for an electric unit at the stages of its design, development, production and usage are described in technical specifications (TS) and standards (GOST). The electric unit should work in accordance with a specific purpose and have significant reliability, durability and safety. The reliability and durability of electric unit significantly depends on restoring strength speed value, that is growth of breakage voltage in arc pass for eliminating repeated arc strike. This article describes several methods of test identification of restoring strength, which were carried out at special testing laboratory units. They are described in relation to conditions of measuring the residual arc column of AC current after it reaches zero point and can be used in designing arc blowout units of low voltage.
-
Date submitted2015-08-25
-
Date accepted2015-10-24
-
Date published2016-04-22
The modern technology of drilling and casing of well during the exploration of gas hydrates
- Authors:
- N. I. Nikolaev
- Lyu Tyanle
In the paper, the perspectives of exploration and completion of gas hydrate fields and the drilling problems in the gas hydrates of the northwest china are studied. It has been established, that the main reasons of complications in the Muli field are the secondary hydrate formation on the walls of the well and drilling assembly and ice formation inside the set cement during the well drilling and completion in permafrost. It has been shown, that in the areas with permafrost during the drilling of the layers containing gas hydrates, temperature and pressure changes can lead to the dissociation of hydrates. At the same time, pressure increase in the annular space due to the gas release, can lead to the secondary formation of gas hydrates, drill string stuck, ceasing of drilling fluid circulation, which is the reason of serious trouble in the wellbore. The results of the research on the development of drilling fluids compositions, which lower the drilling troubles of permafrost, are presented. Comparative experiments have been conducted to evaluate the effectiveness of thermodynamic and kinetic inhibitors, which prevent the repeated hydrate formation. It has been established, that the kinetic inhibitors have the clear advantage: they have good inhibiting effects even with low amounts of additives. In the laboratory conditions, the researches have been conducted to evaluate the phase equilibrium of gas hydrates during their reaction with the water solutions, containing kinetic inhibitor PVP. A thin clay drilling mud has been developed on the water base, providing the holding of the temperature in the level of –2 °С and its effectiveness for the gas hydrate fields in the PRC has been shown. Casing effectiveness of unstable rocks during the drilling in the conditions of negative temperatures inside the well largely depends on their physical-mechanical properties, composition and the technical indicators of cement materials. The authors suggest the composition of quick-setting cements based on aluminum binding materials. It has been established, that the analyzed compositions have the ability to considerably improve the results of cementing.
-
Date submitted2013-07-20
-
Date accepted2013-09-01
-
Date published2014-03-17
Methodological features of intensification natural ventilation pits
- Authors:
- V. A. Rogalev
- K. N. Yastrebova
Effective method of intensification of natural ventilation pits is to ensure steady airflow around the sides of the wind stream. Methodical features of the implementation of this method and the corresponding mathematical algorithm.
-
Date submitted2010-07-12
-
Date accepted2010-09-14
-
Date published2011-03-21
Principles of an automatic control system of ventilation creation the kuznetsovsky railway tunnel
- Authors:
- S. G. Gendler
- V. A. Pleskunov
For effective ventilation Kuznetsovsky railway tunnel the longitudinal scheme of ventilation based on use of jet fans is offered. It is shown that use of the offered scheme of ventilation at influence of natural draft and piston effect of trains is impossible without an automatic control system of ventilation (ACSV). The principles of work ACSV taking into consideration natural and operational factors are proved.
-
Date submitted2009-10-25
-
Date accepted2009-12-19
-
Date published2010-09-22
Principal technologies for prevention of natural dangers at coal mines
- Authors:
- Jozef Dubinsky
Modern mining of mineral resources to be the industry accepted by the society must meet the criteria for sustainable development. Work safety is its important element, which is a particular sphere in underground coal mines in the view of natural hazards occurring numerously, including the catastrophic failures. Among them are gas hazard, fires and rock burst hazard. The selected methodological solutions in terms of their recognition and technologies applicable for the actively combat of these threats, which are featured by high efficiency, have been pointed out.
-
Date submitted2009-09-16
-
Date accepted2009-11-17
-
Date published2010-06-25
Information technology usage during linguistic competitions in technical higher school conducting
- Authors:
- E. V. Terentyeva
This article is devoted to the issue of IT technologies usage for teaching methods in humanities. The article is covering the experience of carrying out the linguistic creative contest among the students of the Mining Institute with the help of the soft «My test». Advantages and disadvantages of the mentioned programme for such kind of workshop are noted in the article. The conclusion for improving of teaching methods with the help of IT technologies is made.
-
Date submitted2009-09-17
-
Date accepted2009-11-07
-
Date published2010-06-25
Test as the form of the economics departments students final knowledge checking at studying the discipline «Business russian as the foreign language»
- Authors:
- E. A. Kolesova
The problems, appearing when compiling test materials for the students-foreigners of the economic professions, studying sphere of business communication, are analyzed in this article. The types of mistakes, allowed students in process of the performing the checking tasks, are systematized. It is offered the examples of the exercises, presented in test.
-
Date submitted2009-09-27
-
Date accepted2009-11-28
-
Date published2010-06-25
Fighting school habits
- Authors:
- A. B. Zhdanov
The article deals with some problems which occur when teaching English to first- and second-year students. The psychological reasons of those are considered from the viewpoint of Russian history, as well as shortcomings of the modern school system. Testing is regarded as a way to solve the problems specified.
-
Date submitted2009-09-19
-
Date accepted2009-11-15
-
Date published2010-06-25
Potassium chloride content in ore and products оf recycling automatic control system
- Authors:
- S. S. Galushkin
- B. A. Vishnyak
- V. N. Smirnov
Potassium chloride percentage in continuous transported ore flows and products of potassium plants recycling automatic control system is offered and described. It differs fundamentally from used before ones at bulk solids containing natural radio-activity elements effective constituents producing and recycling plants. Sensing device is used in this information-measuring system (IMS). It allows to realize automatic control in flows for that instantaneous productivity fluidity in wide limits is resided. Using such IMS gives considerable economic effect by measurements error lowering and their quickness increase.
-
Date submitted2009-07-08
-
Date accepted2009-09-19
-
Date published2010-04-22
Geomechanical and hydrogeological problems оf the Yakovlevsky deposit development
- Authors:
- V. L. Trushko
- A. G. Protosenya
- R. E. Dashko
The article deals with geomechanical and hydrogeological problems under the Yakovlevsky ore deposit development including variations in strength properties. The estimation of feasible underground water inrush inside the mining excavation is done. In situ results of ore strata deformation around excavation are discussed. Numerical modeling of stress and strain in the waterproofing ore pillar due to partially backfilling of excavation is carried out.