-
Date submitted2022-01-20
-
Date accepted2022-07-21
-
Date published2023-12-25
Tribodynamic aspects of the resource of electric submersible vane pumps for oil production
The operation of electric submersible vane pumps for oil production is accompanied by the presence of solid particles, corrosive substances, asphalt-resin-paraffin deposits in the reservoir fluid, leading to changes in performance characteristics and equipment failures. The reduction of the resource as a result of this is accompanied by an increase in the costs of repair and replacement of equipment. The main processes that negatively affect the failure are the wear of the seals of the working stages, the pump plain bearings and vibration, the level of which can significantly exceed the initial level. A test bench and methodology for testing pump sections for wear in water with an abrasive and simultaneous registration of vibration characteristics have been developed. Two main forms of wear of radial seals have been identified – one-sided and equal-dimensional. The one-sided form of sleeve wear is caused by synchronous shaft precession, whereas the equal-dimensional one is an asynchronous precession, and the vibration level increases with increasing wear. The wear distribution of radial seals along the length of the pump correlates with the shape of the elastic shaft line. The wear of the axial seals does not significantly increase the vibration level. During wear the frequency spectrum of vibrations changes; there occurs a frequency that can serve as a diagnostic sign of ultimate wear of the pump. The calculated dependence of the vibration velocity on the wear of the radial seals of the working stages is obtained, which makes it possible to predict the onset of a failure of functioning.
-
Date submitted2022-09-30
-
Date accepted2023-02-13
-
Date published2024-02-29
Improving the efficiency of oil vapor recovery units in the commodity transport operations at oil terminals
- Authors:
- Vladimir V. Pshenin
- Gulnur S. Zakirova
In this paper the problem of losses from evaporation of light fractions of hydrocarbons during loading operations of tanker fleets vessels is considered. It was found that there is no unified approach to modeling the system “tanker – gas phase pipeline – vapor recovery units” in open sources. The absence of a generally recognized model makes it impossible to scientifically justify the application of instruments to reducing losses and the development of corresponding measures. In work it is showed that the dynamics of growth of pressure in the inner tanker capacity is described by a differential equation, considering for non-stationary essence of the process. This equation is converted to a non-dimensional form and investigated in relation to the similarity criteria of this system. This research has allowed to establish unambiguously the general character of pressure changes in the inner tanker capacity, and to predict the peak values of its growth at the initial stage of the loading operation. The obtained equations were tested on real tanker loading data and showed satisfactory convergence with the experimental data. At different stages of the loading opera-tion the component composition of vapor changes, which is shown by chromatographic analysis of the gas mixture. With the availability of a model of hydrocarbon vapor displacement from the inner of tanker, it is possible to propose measures to minimize the negative impact on the environment and return valuable vapors of the product to the technological chain of transportation.
-
Date submitted2022-10-13
-
Date accepted2022-12-13
-
Date published2023-07-19
A complex model of a drilling rig rotor with adjustable electric drive
A modified mathematical model of an asynchronous electric drive of the rotor – a drill string – a bit – a rock is considered and implemented, which develops and generalizes the results of previously performed studies. The model includes the following subsystems: a model of an asynchronous drive with vector control; a model of formation of the resistance moment at the bottom of the bit, taking into account the peculiarities of the interaction between the bit and the rock; a model of a multi-mass mechanical part that takes into account the deformation of the drill string; subsystem for the drilling rig energy-technological parameters formation. The integrated model makes it possible to calculate and evaluate the selected drilling modes, taking into account their electro-mechanical, energy and technological efficiency and the dynamics of drilling processes. The performed computer simulation of drilling modes confirmed the possibility of a stick-slip effect accompanied by high-frequency vibrations during bit stops, which may change the direction of rotation of the bit, its accelerated wear and unscrewing of the drilling tool. Long bit stops lead to a significant decrease in the average bit rotation speed, which can explain the decrease in the ROP and increase in energy consumption when drilling in the zone of unstable bit rotation. The model can be used as a base for further improvement of rotary drilling control systems.
-
Date submitted2022-05-12
-
Date accepted2022-09-15
-
Date published2022-12-29
Problem solution analysis on finding the velocity distribution for laminar flow of a non-linear viscous flushing fluid in the annular space of a well
- Authors:
- Vasiliy I. Nikitin
Modern drilling fluids are non-linear viscous media with an initial shear stress. In classical scientific works on hydromechanical modeling of drilling fluids motion in pipes and annular channels the Shvedov – Bingham approximation and Ostwald – de Waale power-law model were used, which did not fully account for behavior of technological fluids in a wide range of shear rates. This article presents a numerical solution for a mathematical model of drilling fluid motion of the three-parameter Herschel – Bulkley rheological model in the annular space of the well. The Herschel – Bulkley model in the rheological equation takes into account the presence of initial shear stress and a tendency for viscosity to change with shear rate, which distinguishes it from the Ostwald – de Waale and Shvedov – Bingham models. The target function in solving the equation of motion is the velocity distribution in the radial direction of the upward flow of the flushing fluid. The analysis of obtained solution is based on the theory of velocity profile influence on quality of cuttings removal during wellbore cleaning. Due to peculiarities of mathematical statement of the task, which supposes necessity of differential equation of motion solution, Wolfram Mathematica computational software has been used as a calculation tool. The analysis of numerical solution allowed to draw conclusions about the possibility of its application in evaluation of velocity profile when drilling fluid moves in annular space of the well. The possibility for application of modified excess coefficient as a relative quantitative parameter for evaluation of velocity profile uniformity was substantiated.
-
Date submitted2022-03-24
-
Date accepted2022-07-21
-
Date published2022-12-29
A probabilistic study on hole cleaning optimization
- Authors:
- Seyyed Shahab Tabatabaee Moradi
Hole cleaning is considered as one of the most important drilling fluid functions. An efficient hole cleaning ensures a reliable well drilling practice with minimum troublesome problems. In this study, two main steps of hole cleaning, i.e., cuttings removal from under the bit and cuttings transport to the surface are discussed based on the drilling data of a shale formation. The traditional models for optimization of each step are presented. As the models require variety of input data, which are usually subjected to some extent of errors and uncertainties, the output of the model is also an uncertain parameter. Using Monte Carlo simulation, a simple probabilistic study was conducted to quantify the certainty level of the obtained results. Based on the result of this study, it is shown that for the proposed well, a good hole cleaning is expected. However, a more reliable decision for further hole cleaning optimization should be made considering the results of uncertainty analysis.
-
Date submitted2021-10-15
-
Date accepted2022-09-06
-
Date published2022-11-10
Experimental research on the thermal method of drilling by melting the well in ice mass with simultaneous controlled expansion of its diameter
- Authors:
- Danil V. Serbin
- Andrey N. Dmitriev
During the seasonal work of the 64th Russian Antarctic Expedition in 2018-2019 at the “Vostok” drilling facility named after B.B.Kudryashov (“Vostok” station, Antarctic) specialists of Saint Petersburg Mining University conducted experimental investigations on the process of drilling by melting with simultaneous expansion of wells in the ice mass. A test bench and a full-scale model of a thermohydraulic reamer-drilling tool were developed, manufactured and tested for the research. The first bench tests of the full-scale model proved its efficiency and suitability for experimental drilling with simultaneous expansion of wells in ice mass; its operational capabilities were determined and the drawbacks that will be taken into account in future were found out. The article substantiates the choice of constructive elements for thermohydraulic reamer-drilling tool. It is determined that the technology of full diameter drilling with simultaneous expansion of the well in ice mass can be implemented by combining contact drilling by melting and convective expansion with creation of forced near-bottomhole annular circulation of the heated heat carrier. Dependencies of expansion rate on main technological parameters were determined: active heat power of heating elements in penetrator and circulation system, mechanical drilling rate, pump flow rate. According to the results of investigations, the experimental model of thermohydraulic reamer-drilling tool will be designed and manufactured for testing in conditions of well 5G.
-
Date submitted2021-10-18
-
Date accepted2022-01-24
-
Date published2022-04-29
Development of a hydrocarbon completion system for wells with low bottomhole temperatures for conditions of oil and gas fields in Eastern Siberia
The paper presents the results of investigations on the influence of low bottomhole temperatures in the intervals of productive formations on the technological properties of solutions used for drilling and completion of wells in order to determine the possibility of increasing gas recovery coefficient at the field of the “Sila Sibiri” gas pipeline. The analysis of technological measures determining the quality of the productive horizon drilling-in was carried out. It was found out that the dispersion of bridging agent in the composition of the hydrocarbon-based drilling mud selected from the existing methods does not have significant influence on the change in the depth of filtrate penetration into the formation in conditions of low bottomhole temperatures. The main reason for the decrease in the near-bottomhole zone permeability was found out – the increase in plastic viscosity of the dispersion medium of the hydrocarbon-based drilling mud under the influence of low bottomhole temperatures. A destructor solution for efficient wellbore cleaning from hydrocarbon-based solution components in conditions of low bottomhole temperatures was developed. The paper presents the results of laboratory investigations of hydrocarbon-based drilling mud and the developed destructor solution, as well as its pilot field tests. The mechanism of interaction between the destructor solution and the filter cake of the hydrocarbon-based drilling mud ensuring the reduction of the skin factor in the conditions of the geological and hydrodynamic structure of Botuobinsky, Khamakinsky and Talakhsky horizons of the Chayandinskoye oil and gas condensate field has been scientifically substantiated.
-
Date submitted2021-09-22
-
Date accepted2021-11-30
-
Date published2021-12-27
Possibilities for creating Russian high-tech bottomhole assembly
Development of high-tech well electronic measuring systems is aimed at creating modern equipment: telemetry, well geophysical measurement equipment, the architecture of which is divided into basic (with measurement channels for gamma logging and inductive resistance) and advanced (with radioactive, acoustic, magnetic resonance and thermobarometric measurement channels, including azimuthal methods of investigation). Over-the-bit measurement modules, rotary steerable systems are being developed and channels for transmitting data to the surface are being improved. Vice versa, specialized surface equipment with highly integrated software is being created. Different measurement modules are manufactured by different companies, which creates uncertainties in the possibility of interfacing the manufacturers' measurement modules into a single well measurement system. The article presents an analysis of the readiness of Russian oil service companies to produce well and surface equipment for drilling Russian directional oil and gas wells, meeting modern requirements for accuracy, lifetime and operating conditions. The possibility of creating a fully Russian well high-tech equipment and the required resources, risks and measures to mitigate them when creating a modern well measurement system are considered.
-
Date submitted2021-03-05
-
Date accepted2021-10-18
-
Date published2021-12-16
Physical and mathematical model of rock destruction by a milling machine cutter
As a result of the analysis of the work on rock destruction by cutters of milling of machines, it was found that the existing developments do not allow us to proceed to the derivation of calculation d dependencies for determining fracture resistance, or can be used only in preliminary calculations of the known by design parameters of milling machines. To eliminate these disadvantages, a combined physical and mathematical model of the process of interaction of a single milling cutter with a spherical tip with the rock has been developed. Consideration of the physical picture of the action of forces and stresses acting from the cutter with spherical tips on the separating rock element in the limiting condition allowed to describe analytically the components of total resistance, which are the mathematical part of the physical and mathematical model of rock destruction by cutters. Analytical dependences for determining the tangential and normal components of fracture resistance of rocks of medium hardness have been obtained. The adequacy of the physical and mathematical model to the physical process of destruction of rocks of different hardness by cutters on a universal stand was tested both in the field and in the laboratory conditions. Technical evaluation of the results of experimental studies confirms the reliability of the developed physical and mathematical model.
-
Date submitted2020-05-21
-
Date accepted2020-10-05
-
Date published2020-11-24
Method of calculating pneumatic compensators for plunger pumps with submersible drive
- Authors:
- Eduard O. Timashev
One of the most promising ways to improve the efficiency of mechanized oil production is a plunger pump with a submersible drive, which allows obtaining harmonic reciprocating movement of the plunger. In the pumping process of well products by plunger pumps, oscillations in the velocity and pressure of the liquid in the lifting pipes occur, which lead to an increase in cyclic variable loads on the plunger, a decrease in the drive life period and the efficiency of the pumping unit. To eliminate the pulsation characteristics of the plunger pump and increase the reliability indicators of the pumping unit (in particular, the overhaul period), pneumatic compensators can be used. A method for calculating the optimal technological parameters of a system of deep pneumatic compensators for plunger pumping units with a submersible drive, based on mathematical modeling of hydrodynamic processes in pipes, has been developed. Calculations of the forming flow velocity and pressure in the lifting pipes of submersible plunger units equipped with pneumatic compensators (PC) have been carried out. Influence of the PC technological parameters on the efficiency of smoothing the oscillations of velocity and pressure in the pipes has been analyzed. Non-linear influence of the charging pressure and PC total volume on the efficiency of their work has been established. Optimal pressure of PC charging, corresponding to the minimum pressure in the tubing during the pumping cycle for the considered section of the tubing, is substantiated. Two ultimate options of PC system placement along the lifting pipes are considered. In the first option, PC are placed sequentially directly at the outlet of the plunger pump, in the second - evenly along the lift. It is shown that the first option provides the minimum amplitude of pressure oscillations at the lower end of the tubing and, accordingly, variable loads on the pump plunger. Nature of the pressure and flow velocity oscillations in the tubing at the wellhead for both options of PC placement has similar values .
-
Date submitted2019-11-28
-
Date accepted2020-05-08
-
Date published2020-10-08
Development of the drilling mud composition for directional wellbore drilling considering rheological parameters of the fluid
Article presents investigations on the development of a drilling mud composition for directional wells in an oil field located in the Republic of Tatarstan (Russia). Various rheological models of fluid flow and their applicability for drilling muds are analyzed. Laboratory experiments to measure the main rheological parameters of a solution, such as plastic viscosity, dynamic shear stress, as well as indicators of non-linearity and consistency are presented. On the basis of laboratory investigations, it was concluded that high molecular weight polymer reagents (for example, xanthan gum) can give tangible pseudoplastic properties to the washing fluid, and their combination with a linear high molecular weight polymer (for example, polyacrylamide) reduces the value of dynamic shear stress. Thus, when selecting polymer reagents for treating drilling muds at directional drilling, it is necessary to take into account their structure, molecular weight and properties. Combination of different types of reagents in the composition of the drilling mud can lead to a synergistic effect and increase the efficiency of the drilling process as a whole.
-
Date submitted2019-09-25
-
Date accepted2019-12-20
-
Date published2020-04-24
Study of the well near-bottomhole zone permeability during treatment by process fluids
- Authors:
- Evgenii A. Rogov
In the process of drilling-in productive horizons, several irreversible physical and chemical processes take place in the near-wellbore zone of the formation: stress state of the rocks changes, penetration of the filtrate and solid phase, as well as drilling mud into the reservoir, and swelling of clay particles of intergranular cementing material are observed. As a result, permeability of productive horizon is significantly reduced and, consequently, potential inflow of oil or gas from formation is excluded. An equally serious problem exists during well servicing and workover, when the use of irrational fluids of well killing causes negative consequences associated with deterioration of reservoir properties of formations in the wells being repaired. Article presents the results of the experiments on permeability of clayed porous samples after exposure to various compositions of liquids. In order to increase permeability of near-borehole zone of the formation and increase productivity of wells completed by drilling, and after well servicing and workover, a composition of the process fluid containing a 15 % aqueous solution of oxyethylene diphosphonic acid (OEDA) with addition of a surfactant is proposed.
-
Date submitted2018-11-09
-
Date accepted2019-01-22
-
Date published2019-04-23
Determining the stability of the borehole walls at drilling intervals of loosely coupled rocks considering zenith angle
- Authors:
- P. A. Blinov
During development of drilling projects, a whole array of data is needed considering the properties of rocks and the conditions of their bedding. Accounting for geomechanical processes occurring in the near-wellbore zone allows avoiding many complications associated with the violation of the wellbore walls stability at all stages of its construction and operation. Technological and technical factors such as vibration and rotation of the drilling string, formation of launders during the descent and ascent of the assembly, pressure pulsation during the start and stop of pumps, hydrostatic and hydrodynamic pressure of the drilling fluid, its composition and properties, have a great influence on the stress-strain state of the medium opened by the well. The washing fluid circulating in the well should provide backpressure to the reservoir, not interact with the rocks chemically, colmatage channels in porous and fractured rocks, preventing penetration of the mud into the medium, by creating an impermeable barrier at drilling clay seams that are prone to swelling, cracking, etc. The article discusses the method for determining the stability of the directed well walls, taking into account the penetration of drilling mud into the pores and fractures of rocks. The technique will allow adjusting the zenith angle of the well during the workout of an unstable interval at the design stage, or selecting a drilling fluid composition to ensure fail-safe drilling.
-
Date submitted2018-09-01
-
Date accepted2018-10-28
-
Date published2019-02-22
Mathematical modeling of rock crushing and multiphase flow of drilling fluid in well drilling
The aim of the work is a mathematical modeling of the rock crushing during drilling and removal of the drilling cuttings (sludge) to the surface by drilling fluid. The process of rock destruction is described using the mathematical theory of fragmentation. The distribution of sludge particles in size and mass depends on such factors as the properties of the drilled rock, the rate of penetration, the type of bit, and the output power. After the formation of sludge, the process of its removal to the surface is modeled. The drilling fluid together with the rock particles is considered as a heterogeneous multiphase medium in which the carrier phase – the drilling fluid – is a non-Newtonian fluid. The flow of such a medium is described using a mixture model in the framework of the multi-fluid approach. This results in a system of nonlinear partial differential equations, for which a new closure relation is derived. To solve the system, the SIMPLE algorithm is used. As a result, the flow properties are studied with the inclusion of particles of various sizes. In particular, for particles of small size due to the action of plastic stresses in a non-Newtonian drilling fluid, an equilibrium mode arises in which the particles move with the drilling fluid without slipping. This is the fastest mode of delivery of sludge to the surface. The specific dimensions of such particles depend on the parameters of the drilling process. In particular, the appropriate size range can be adjusted by changing the parameters of the drilling fluid.
-
Date submitted2018-05-04
-
Date accepted2018-07-23
-
Date published2018-10-24
Analysis of possible enhancementof properties of VK15 material used for drilling tools
- Authors:
- Yu. A. Kurganova
- K. S. Panina
- P. S. Beshenkov
Traditionally, when drilling hard and abrasive rocks, it is recommended to use a tungsten-cobalt hard alloy VK15. The analysis of information on the possibility of improving the potential of the material has demonstrated the existence of mechanisms that provide structural transformations that enhance its strength, hardness and toughness. The use of such technology instead of traditional methods will lead to an increase in the operating efficiency and durability of the tool. During the work, experimental samples of alloy VK15 were obtained by sintering in four different modes. Then their properties were analyzed. The results of the metallographic study carried out on the «Carl Zeiss» microscope made it possible to estimate the distribution of tungsten carbide grains in cobalt bon and show the grinding of the carbide phase. Thus, with traditional sintering, the amount of tungsten carbide grains with an average size of less than 1 μm in diameter from the entire size range reaches 19.5 %, while after additional heat treatment with a holding time of 1280 °C, the value was 41.5 %; 900 °C – 59.1 %; 600 °С – 54.5 %. The maximum improvement results were the following: hardness by 18 %, a coercive force by 49 %, and crack resistance by 11 % of the traditional alloy, there were achieved at 900-1280 °C. A hypothesis has been put forward on the formation of additional structural elements not detected by the methods of optical metallography. Studies of the topology and structure of the samples on an atomic force microscope confirmed the presence of nanoscale inclusions from 20 to 40 nm (presumably tungsten carbide) in a cobalt bond.For VK15, comparative studies of properties and analysis of the microstructure of experimental samples obtained by the traditional sintering and modified technology have shown that the sintering mode at 900 °C is a priority.
-
Date submitted2018-01-02
-
Date accepted2018-03-14
-
Date published2018-06-22
Analysis of the options of modernization of roller-bit drilling machines with a submersible steamer
- Authors:
- D. A. Yungmeister
- I. Krupenskii
- S. A. Lavrenko
The designs of submersible hammers and dampers protected by patents for reducing the vibration of the drilling rig of roller drill machines are proposed. The variants of modernizing drilling rigs for drilling hard rocks and faces of complex structures are considered. Particular attention is paid to the joint work of submersible shockers and pneumatic shock absorbers, the preferred schemes for the arrangement of these devices by drilling rigs are indicated. The results of experimental tests of machines with pneumatic hammers are presented to determine the vibration performance and drilling speeds. The pneumatic hammer allows increasing the speed of drilling process to the intensification of the destruction of the plain face by the shock load and the cleavage of the protrusions of the unevenness of the face, the better fitting of the bit to the face and the release of the blades or the bit pins from the drill bit. The choice of a particular type of damper or shock absorber depends on its design scheme and the possibility of changing the design of the drill string. With the complexity of installing a damping device in the mast (with significant dimensions of shock absorbers and drilling of strong heterogeneous rocks), it is advisable to use a set of tools to reduce hydraulic pulsations in the mains and cylinders of the hydraulic system by installing chokes in the oil plants and pneumatic shock absorbers. It is proposed to use the device for the development of pneumatic hammers by a patent-pending drilling method with a hollow piston filled with magnetically active heavy liquid, which will allow controlling the frequency and size of the shock pulses and partially compensating for the drill string fluctuations arising from the uneven immersion of the bit in the array . It is noted that the proposed solutions increase the drilling speed by an average of 15%.
-
Date submitted2018-01-15
-
Date accepted2018-03-24
-
Date published2018-06-22
Designing of well trajectory for efficient drilling by rotary controlled systems
- Authors:
- M. V. Dvoinikov
The main directions of increasing the efficiency of drilling wells by improving methods for designing profiles of directional and horizontal wells are identified. The feasibility and necessity of using at drilling with rotary controlled systems the trajectories of directed wells' profiles with continuous curving, that do not contain conjugated sections, on the basis of plane transcendental curves are theoretically substantiated and experimentally confirmed. An algorithm and software are developed that allow optimal selection of a profile or a trajectory section, taking into account minimization of twisting, bending, compressive and tensile stresses that ensure the efficiency of technical and technological parameters of well drilling.
-
Date submitted2017-08-30
-
Date accepted2017-11-21
-
Date published2018-02-22
Simulation of operation of pneumatic compensator with quasi-zero stiffness in the electric centrifugal submersible pump unit
- Authors:
- A. N. Zotov
- K. R. Urazakov
- E. B. Dumler
The ECSPU pneumatic compensators with quasi-zero stiffness are proposed. The pneumatic compensator with quasi-zero stiffness is suggested to be made in the form of pneumatic spring assemblies having a power characteristic with a positive stiffness working area and a set of successively connected Belleville springs and a power characteristic with a working area of negative stiffness. Structurally, a set of Belleville springs is located inside the air spring and supports pneumatic compensator piston. As a result of adding the negative stiffness of the disc spring washers set and the positive stiffness of the pneumatic spring, the resulting system (the proposed pneumatic compensator) acquires a quasi-zero or specified low stiffness. The efficiency of the suggested pneumatic compensator was determined by the possibility of moving its piston from the effects of various pressure drops. It was assumed that the greater the distance the piston can move under a given action, the more effective the pneumatic compensator is. The effect of various forces acting on the piston in the case of pressure drops on the discharge line of the electric centrifugal submersible pump units (ECSPU) is simulated: a rapidly decreasing load; a sudden increase in the force acting on the piston and vibration impact. In all the considered examples, the displacement of the piston was several meters, which corresponds to the length of the working area of the power characteristic of the considered pneumatic compensator with quasi-zero stiffness. It is shown that existing pneumatic compensators, which are like gas caps, are in principle unable to provide the same displacement of the piston under the same effects on it. For their effective operation, the size of the gas cap should be several tens of meters, which is impossible in the conditions of the well. In the calculations, it is shown that it is possible to manufacture the necessary disk spring washers from various materials: steel; fiberglass FGM; beryllium bronze. Of particular interest are disk spring washers made of beryllium bronze, which are capable of withstanding up to 20 billion load cycles.
-
Date submitted2016-09-01
-
Date accepted2016-11-05
-
Date published2017-02-22
Research on technical and technological parameters of inclined drilling
- Authors:
- M. V. Dvoinikov
An analysis of operational capabilities of inclined drilling equipment and technology is presented. Two options of rotary drilling are reviewed as technical and technological solutions, facilitating construction of wells with difficult profiles. The first option implies that the driver unit of the drill bit is represented by downhole drilling motor, the second one utilizes sophisticated rotary steerable systems. Practical results of drilling wells with difficult profiles are presented. A quality assessment of drilling is provided through the example of comparing designed and actual trajectories, using different driver units for the drill bit, as well as properties of surrounding rocks, rheology of the drill fluid and other characteristics of dynamically active systems. A range of rotation speed has been determined that allows rotary steerable systems to have minimal oscillation amplitude of the bottom-hole assembly. Analysis of investigation results showed that the main source of oscillations is linked to bending and compressing stresses, caused by well deviations as well as rigidity of the drilling tool. In effect, in the bottom-hole assembly occur auto-oscillations, making it impossible to correct azimuth and zenith angles. Alteration of rigidity in the bottom part of the tool and drilling parameters, implying reduced rotation speed of the drill string and regulation of drill bit pressure, can partially solve this problem, though increase in rotation speed is limited by technical characteristics of existing top drive systems.
-
Date submitted2015-08-25
-
Date accepted2015-10-24
-
Date published2016-04-22
The modern technology of drilling and casing of well during the exploration of gas hydrates
- Authors:
- N. I. Nikolaev
- Lyu Tyanle
In the paper, the perspectives of exploration and completion of gas hydrate fields and the drilling problems in the gas hydrates of the northwest china are studied. It has been established, that the main reasons of complications in the Muli field are the secondary hydrate formation on the walls of the well and drilling assembly and ice formation inside the set cement during the well drilling and completion in permafrost. It has been shown, that in the areas with permafrost during the drilling of the layers containing gas hydrates, temperature and pressure changes can lead to the dissociation of hydrates. At the same time, pressure increase in the annular space due to the gas release, can lead to the secondary formation of gas hydrates, drill string stuck, ceasing of drilling fluid circulation, which is the reason of serious trouble in the wellbore. The results of the research on the development of drilling fluids compositions, which lower the drilling troubles of permafrost, are presented. Comparative experiments have been conducted to evaluate the effectiveness of thermodynamic and kinetic inhibitors, which prevent the repeated hydrate formation. It has been established, that the kinetic inhibitors have the clear advantage: they have good inhibiting effects even with low amounts of additives. In the laboratory conditions, the researches have been conducted to evaluate the phase equilibrium of gas hydrates during their reaction with the water solutions, containing kinetic inhibitor PVP. A thin clay drilling mud has been developed on the water base, providing the holding of the temperature in the level of –2 °С and its effectiveness for the gas hydrate fields in the PRC has been shown. Casing effectiveness of unstable rocks during the drilling in the conditions of negative temperatures inside the well largely depends on their physical-mechanical properties, composition and the technical indicators of cement materials. The authors suggest the composition of quick-setting cements based on aluminum binding materials. It has been established, that the analyzed compositions have the ability to considerably improve the results of cementing.
-
Date submitted2013-07-18
-
Date accepted2013-09-30
-
Date published2014-03-17
Reducing environmental hazard drilling works
- Authors:
- M. M. Malyshkin
The problem of disposal of drilling waste is proposed to solve through the introduction of protective functions of the complex engineering activities, including, firstly, the application in the process of drilling mud through watersoluble biodegradable polymers and quadruple systems, cleaning fluid, and secondly, the application design platform with the wells trench in the body of the embankment site for pressed cuttings, which is arranged for a temporary earthen vessel for drilling wastewater.
-
Date submitted2010-07-19
-
Date accepted2010-09-22
-
Date published2011-03-21
Simulation of swinging movement autoresonant electric drive with nonsymmetric excitation
- Authors:
- A. N. Fomenko
Mathematical and simulation models of drill bit oscillations. Method for calculating the model works elastic, electromagnetic and load torques has been developed. Simulation results of autoresonant regimes with asymmetric excitation oscillations of dynamically counter balanced drilling string on the cargo-carrying cable drill bit are represented.
-
Date submitted2010-07-20
-
Date accepted2010-09-14
-
Date published2011-03-21
The physical breadboard model of dynamically counterbalanced drilling string with swinging movement with the asynchronous electric drive powered by inverter laboratory experimental researche
- Authors:
- V. V. Ivanik
The laboratory experimental stand for research of the asynchronous resonant electric drive on a physical breadboard model of dynamically counterbalanced drilling string is developed. The asynchronous electric drive with swinging movement the autoresonant oscillation mode is realized.
-
Date submitted2010-07-21
-
Date accepted2010-09-28
-
Date published2011-03-21
Swinging movement autoresonant electric drive with nonsymmetric excitation of dynamically counter-balanced drilling string on carrying cable
- Authors:
- E. A. Zagrivnyi
- A. N. Fomenko
Considered nonsymmetric mode of drill bit oscillations when forming a unipolar electromagnetic torque on each cycle oscillations of dynamically balanced drill . Developed a method for estimating speed of rotation drill around its axis when working in the nonsymmetric mode at first approximation .
-
Date submitted2010-07-08
-
Date accepted2010-09-02
-
Date published2011-03-21
The autoresonant asynchronous electric drive of dynamically counterbalanced drilling string on carrying cable with swinging movement fluctuations amplitude stabilization
- Authors:
- E. A. Zagrivnyi
- V. V. Ivanik
The algorithm of resonant fluctuations amplitude stabilization of dynamically counterbalanced drilling string on carrying cable with swinging movement of jackbit is developed. Imitating modeling of the resonant asynchronous electric drive with swinging movement of jackbit with the frequency converter in various operating modes is resulted.