-
Date submitted2023-05-21
-
Date accepted2024-05-02
-
Date published2024-08-26
Assessment of the influence of lithofacies conditions on the distribution of organic carbon in the Upper Devonian “Domanik” deposits of the Timan-Pechora Province
The study of high-carbon formations was instigated both by the decreasing raw material base of oil as a result of its extraction, and by the progress in development of low-permeability shale strata, primarily in the USA, Australia, and China. The most valuable formations occur in traditional hydrocarbon production areas – the West Siberian, Volga-Ural and Timan-Pechora, North Pre-Caucasian and Lena-Tunguska oil and gas provinces. Specific features of the Late Devonian-Early Carboniferous high-carbon formation occurring in the eastern marginal part of the East European Platform are: heterogeneous section due to intense progradation of the carbonate platform from west to east; succession of lithofacies environments that determined the unevenness of the primary accumulation and secondary distribution of organic matter (OM); possible migration or preservation in the source strata during the subsidence stages of the moving parts of bitumides, which determined the prospects for oil and gas potential. The distribution pattern of the present OM content was investigated depending on lithofacies conditions and lithological composition of rocks in the “Domanik type” Upper Devonian-Tournaisian deposits in the Timan-Pechora Province (TPP), its transformation degree to bring it to the initial content of organic carbon and further estimation of the share of stored “mobile oil” in oil and gas source formation. The study was based on the analysis of the data set on organic carbon content in core samples and natural exposures in the Ukhta Region in the Domanik-Tournaisian part of the section including more than 5,000 determinations presented in reports and publications of VNIGRI and VNIGNI and supplemented by pyrolytic and bituminological analyses associated with the results of microtomographic, macro- and lithological studies and descriptions of thin sections made at the Saint Petersburg Mining University. For each tectonic zone of the TPP within the investigated high-carbon intervals, the content of total volumes of organic carbon was determined. The data obtained allow estimating the residual mass of mobile bitumoids in a low-permeability matrix of the high-carbon formation.
-
Date submitted2023-04-06
-
Date accepted2023-12-27
-
Date published2024-04-25
Localization of sites for the development of geomechanical processes in underground workings based on the results of the transformation and classification analysis of seismic data
The paper considers an approach to localizing the intervals of development of geomechanical processes in underground structures based on the classification and transformation of seismic data. The proposed approach will make it possible to identify the intervals of fracturing, rock decompression, water inflow and other geomechanical processes when interpreting the results of seismic surveys. The technique provides for the formation of matrices of longitudinal (Vp), transverse (Vs) velocities and velocity ratios (Vs/Vp) along the research profile to perform sequential filtration. The filtration results serve as the basis for the formation of a bank of informative materials for further classification. Based on the domestic KOSKAD 3D software, four approaches have been implemented for a combined digital model of the Vp, Vs and Vs/Vp parameters. One of the key elements in the classification process is to combine grids to increase the probability of detecting intervals with heterogeneous identification features. The result of the application of this methodical approach is the construction of a comprehensive interpretative model, on which potential zones of geomechanical risks development are clearly manifested.
-
Date submitted2023-02-27
-
Date accepted2023-10-25
-
Date published2024-04-25
Microstructural features of chromitites and ultramafic rocks of the Almaz-Zhemchuzhina deposit (Kempirsai massif, Kazakhstan) according to electron backscatter diffraction (EBSD) studies
Microstructural features of the main rock-forming minerals of host ultramafic rocks (olivine, orthopyroxene) and chrome spinel from ores of the Almaz-Zhemchuzhina deposit were studied using the electron backscatter diffraction method. For ultramafic rocks, statistical diagrams of the crystallographic orientation of olivine and orthopyroxene were obtained, indicating the formation of a mineral association in conditions of high-temperature subsolidus plastic flow in the upper mantle. The main mechanisms were translation gliding and syntectonic recrystallization. Olivine deformation occurred predominantly along the (010)[100] and (001)[100] systems. The textural and structural features of chromitites reflect plastic flow processes, most pronounced in lenticular-banded ores. Microstructure maps in inverse pole figure encoding show differences in the grain size composition of the ores: areas consisting of disseminated chromitites are characterized by a finer-grained structure compared to lens-shaped segregations of a massive structure. Analysis of microstructure maps shows that during the transition from disseminated to massive ores, there is a widespread development of recrystallization, adaptation of neighbouring grains to each other, resulting in homogenization of crystallographic orientation in aggregates. The data obtained develop ideas about the rheomorphic nature of chromitite segregations in ophiolite dunites. It is assumed that the coarsening of the structure of massive chromitites is critically associated with an increase in the concentration of ore grains during solid-phase segregation within a plastic flow, when individual chrome spinel grains, initially separated by silicate material, begin to come into direct contact with each other.
-
Date submitted2022-04-07
-
Date accepted2023-04-21
-
Date published2023-08-28
Development of a new assessment system for the applicability of digital projects in the oil and gas sector
Digital transformation is one of the global trends that has covered most sectors of the economy and industry. For oil and gas companies, the introduction of digital technologies has become not just a trend, but one of the factors for ensuring competitiveness and maintaining a stable position in the market in a rapidly changing macro environment. At the same time, despite the positive effects achieved, digital transformation is a complex process from the point of view of implementation and is associated with high technological, financial, and economic risks. The work aims to develop and test a new system for evaluating the applicability of digital projects in the oil and gas sector. The research methodology includes the application of the Gartner curve, methods of expert assessments, and tools for assessing the economic efficiency of investment projects. The developed assessment system is based on a comprehensive accounting of four components: the level of digital maturity of the company; compliance of the implemented technology with the goals and objectives of the organization; the level of reliability of the implemented technology; the level of innovation of the implemented project. Particular attention is paid to the practical testing of the proposed methodology based on the evaluation of a digital project implemented by a Russian oil and gas company.
-
Date submitted2022-10-29
-
Date accepted2023-02-13
-
Date published2023-04-25
The use of unmanned aerial photography for interpreting the technogenic transformation of the natural environment during the oilfield operation
The traditional approach to monitoring observations of the technogenic processes development in oilfields, which consists in determining the concentration of marker pollutants in various natural environments, does not provide the necessary completeness of information and the efficiency of its receipt. The paper considers an example of expanding the range of observations due to unmanned aerial photography and a number of other methods. Interpretation signs (for panchromatic survey) were determined that register such consequences of technogenic transformation of the natural environment as mechanogenesis, bitumization, and halogenesis. Technogenic mechanogenesis is understood as a physical violation of the integrity of ecosystems, the movement of soils and grounds. Bitumization is expressed in the migration of petroleum hydrocarbons through soils, ground, surface, subsurface, and underground waters, and their destruction. Salt migration in these media is defined as halogenesis. The most reliable indicators are linearly elongated areas of dead forests, dark red spots in drying microdepressions and reservoirs. It was found out that the oilfield impact on the raised bog leads to anthropogenic eutrophication, the introduction of plant species, uncharacteristic coenotic groups, the replacement of subshrubs with grasses, and morphometric changes in forest pine. In the peat deposits of the disturbed area, an unusual interlayer of whitish, undecomposed moss was recorded. The moment of the beginning of a pronounced technogenic transformation was registered in the course of work with the archive of multispectral space images. Continuous remote sensing with the help of unmanned aerial photography and interpretation by sedimentological, geobotanical methods significantly expand the possibilities of studying the technogenic transformation of the natural environment. To ensure environmental safety, it is advisable to develop remote methods and technologies to include them in the environmental monitoring system.
-
Date submitted2022-02-26
-
Date accepted2022-04-27
-
Date published2022-07-26
Type intrusive series of the Far East belt of lithium-fluoric granites and its ore content
- Authors:
- Viktor I. Alekseev
The evolution and ore content of granitoid magmatism in the Far East belt of lithium-fluoric granites lying in the Russian sector of the Pacific ore belt have been studied. Correlation of intrusive series in the Novosibirsk-Chukotka, Yana-Kolyma and Sikhote-Alin granitoid provinces of the studied region allowed to establish the unity of composition, evolution, and ore content of the Late Mesozoic granitoid magmatism. On this basis, a model of the type potentially ore-bearing intrusive series of the Far East belt of lithium-fluoric granites has been developed: complexes of diorite-granodiorite and granite formations → complexes of monzonite-syenite and granite-granosyenite formations → complexes of leucogranite and alaskite formations → complexes of rare-metal lithium-fluoric granite formation. The main petrological trend in granitoid evolution is increasing silicic acidity, alkalinity, and rare-metal-tin specialization along with decreasing size and number of intrusions. At the end of the intrusive series, small complexes of rare-metal lithium-fluoric granites form. The main metallogenic trend in granitoid evolution is an increasing ore-generating potential of intrusive complexes with their growing differentiation. Ore-bearing rare-metal-granite magmatism of the Russian Far East developed in the Late Cretaceous and determined the formation of large tungsten-tin deposits with associated rare metals: Ta, Nb, Li, Cs, Rb, In in areas with completed intrusive series. Incompleteness of granitoid series of the Pacific ore belt should be considered as a potential sign of blind rare-metal-tin mineralization. The Far East belt of lithium-fluoric granites extends to the Chinese and Alaskan sectors of the Pacific belt, which allows the model of the type ore-bearing intrusive series to be used in the territories adjacent to Russia.
-
Date submitted2021-09-29
-
Date accepted2022-05-11
-
Date published2022-07-13
Tensor compaction of porous rocks: theory and experimental verification
Compaction in sedimentary basins has been traditionally regarded as a one-dimensional process that ignores inelastic deformation in directions orthogonal to the active load. This study presents new experiments with sandstone demonstrating the role of three-dimensional inelastic compaction in cyclic true triaxial compression. The experiments were carried out on the basis of a triaxial independent loading test system in the Laboratory of Geomechanics of the Ishlinsky Institute for Problems in Mechanics of the Russian Academy of Science. The elastic moduli of the material were estimated from the stress-strain curves and the elastic deformations of the sample in each of the three directions were determined. Subtracting the elastic component from the total deformation allowed to show that inelastic compaction of the sandstone is observed in the direction of active loading, whereas in the orthogonal directions there is a expansion of the material. To describe the three-dimensional nature of the compaction, a generalization of Athy law to the tensor case is proposed, taking into account the role of the stress deviator. The compaction tensor and the kinetic equation to describe the evolution of inelastic deformation, starting from the moment of the load application are introduced. On the basis of experiments on cyclic multiaxial compression of sandstone, the identification and verification of the constructed model of tensor compaction were carried out. The possibility of not only qualitative, but also quantitative description of changes in inelastic deformation under complex cyclic triaxial compression is shown.
-
Date submitted2021-03-18
-
Date accepted2021-11-30
-
Date published2021-12-27
Deformations assessment during subway escalator tunnels construction by the method of artificial freezing of soil for the stage of ice wall formation
- Authors:
- Evgenii M. Volokhov
- Diana Z. Mukminova
The work is devoted to the study of the processes of displacement and deformation of the surface during the escalator tunnels construction of the subway by the method of artificial freezing of soils. The features of the construction and freezing technology, the rocks characteristics in which the escalator tunnels made are considered. The data of specially organized, full-scale surveying observations of deformations on the earth surface are presented. The main factors influencing deformation processes in the frozen strata of a layered inhomogeneous rock mass with inclined tunneling are determined, the complexity of the predictive task and the need to simplify the design scheme are shown. The work is focused on the assessment of the least studied geomechanical processes of soil heaving-uplifts and deformations during the periods of active and passive freezing stages. When studying the displacements processes of the earth surface and rock mass, the finite element method and analysis of the obtained data using field observations of displacements were used. A simplified calculation scheme is proposed for modeling, which allows taking into account the uneven influence of frozen rocks of an inhomogeneous layered rock mass with a large inclined tunneling. The satisfactory convergence of the data of field surveying observations on the earth surface and the results of modeling geomechanical processes for the period of active and passive freezing stages is shown. The proposed calculation scheme is recommended for the prediction of deformation at the stages of underground construction, characterized by the development of the most dangerous tensile deformations of buildings and structures on the surface.
-
Date submitted2020-09-10
-
Date accepted2020-11-25
-
Date published2021-06-24
Formation conditions of noble metal mineralization in sulfide cobalt-copper-nickel ores of Kamchatka (on the example of Annabergitovaya Schel ore occurrence)
The authors present research results, the purpose of which is to study the specifics of noble metal mineralization and its genesis in sulfide cobalt-copper-nickel ores of the Kamchatka nickel-bearing province. The paper is dedicated to one of its many ore occurrences called Annabergitovaya Schel (Annabergite Gap). The material composition of platinoid, silver, gold, bismuth and tellurium minerals, as well as sulfarsenides in the ores of this occurrence was investigated. Based on the data of mineral formation sequence and the use of geosensors, conclusions were drawn regarding the genesis of noble metal mineralization. Formation of platinoid minerals, silver and gold at the Annabergitovaya Schel ore occurrence is mainly associated with the epigenetic effect of post-ore granitoids on ore-bearing intrusion rocks of the Dukuk complex of the cortlandite-norite formation and on syngenetic ores. An early association of noble metal minerals is represented by sperrylite, irarsite, and rare unnamed phases of Pt + Ir + Te. Irarsite and Pt + Ir + Te phases were formed at the contact-metasomatic stage. Sperrylite can be assumed to be of magmatic origin. Silver sulfides and tellurides, silver and palladium bismuth tellurides, and native gold were formed at the late, hydrothermal-metasomatic, stage. The occurrence conditions of mineral parageneses, associated with noble metal mineralization, correspond to the formation of shallow-depth metasomatic rocks (≤5 km). Sub-developed quartz-feldspar metasomatites, associated with the formation of early platinoid arsenides and sulfarsenides, are in equilibrium with circumneutral solutions (pH of 4.5-6.5) at temperatures of 350-600 °C. Late hydrothermal association with Pd, Ag and Au minerals is close to propylites and was formed at pH values of 4.5-6.5 and temperature of 150-350 °C.
-
Date submitted2020-07-30
-
Date accepted2021-03-02
-
Date published2021-04-26
Experimental study of thermomechanical effects in water-saturated limestones during their deformation
Stability control of elements of stone constructions of various structures is a prerequisite for their safe operation. The use of modern methods of non-destructive diagnostics of the stress-strain state of such constructions is an effective, and in many cases the only way to control it. Studies of thermal radiation accompanying the processes of solid bodies deformation allowed to justify and develop a method that allows to obtain non-contact information about changes in the stress-strain state in various types of geomaterials, including limestones. However, studies of the water saturation influence of rocks on the thermal radiation parameters recorded in this way are currently superficial. Taking into account the water saturation degree of rocks is necessary when monitoring the mechanical condition of stone structures that are in direct contact with water. The main purpose of this work is to study the dependences of changes in the intensity of thermal radiation from the surface of limestone samples with different humidity under conditions of uniaxial compression. The obtained results showed the expected significant decrease in the mechanical properties (uniaxial compressive strength and elastic modulus) of water-saturated samples in comparison with dry ones. At the same time, a significant increase in the intensity of thermal radiation of limestone samples subjected to compression with an increase in their water saturation was recorded, which makes it necessary to take into account the revealed regularity when identifying changes in the stress state of stone structures established according to non-contact IR diagnostics in real conditions.
-
Date submitted2019-07-17
-
Date accepted2019-10-09
-
Date published2020-04-24
Assessment of internal pressure effect, causing additional bending of the pipeline
Article justifies accounting for internal pressure effect in the pipeline, causing additional bending of the pipeline. According to some scientists, there is an erroneously used concept of the equivalent longitudinal axial force (ELAF) S x , which depends on working pressure, temperature stresses, and joint deformations of pipelines with various types of soils. However, authors of the article use ELAF S x concept at construction of mathematical model of stress-strain state (SSS) for complex section of the trunk pipeline, and also reveal it when analyzing the results of calculating the durability and stability of the pipeline. Analysis of SSS for calculated section of the pipeline was carried out for two statements of the problem for different values of operation parameters. In the first statement, effect of internal pressure causing bending of the pipeline is taken into account, and in the second it is neglected. It is shown that due to effect of ELAF S x at p 0 = 9.0 MPa, Dt = 29 °C extreme value of bend increases by 54 %, extreme values of bending stresses from span bending moment increase by 74 %, and extreme value of bending stresses from support bending moment double with regard to corresponding SSS characteristics of the pipeline. In case of neglecting the internal pressure effect causing additional bending of the pipeline (second statement of the problem), error in calculating the extreme value of bend is 35 %, extreme value of bending stresses from span bending moments is 44 %, and extreme value of bending stresses from support bending moments is 95 %.
-
Date submitted2019-05-30
-
Date accepted2019-09-03
-
Date published2020-02-25
Study on influence of two-phase filtration transformation on formation of zones of undeveloped oil reserves
- Authors:
- S. I. Grachev
- V. A. Korotenko
- N. P. Kushakova
In order to study the process of fluid filtration during flooding of an oil field, article uses Rapoport – Lis model of non-piston oil displacement by water. During plane-radial filtration in a homogeneous formation, radii of disturbance zones are determined with and without taking into account the end effect. Influence of changes in value of capillary pressure gradient on distribution of water saturation coefficient in the non-piston displacement zone for high and low permeability reservoirs is revealed. Application of an element model for a five-point injection and production well placement system showed that, using traditional flooding technology, flat-radial fluid filtration is transformed into rectilinear-parallel. At solving equation of water saturation, Barenblatt method of integral relations was used, which allows determining the transformation time. By solving the saturation equation for rectilinear-parallel filtration, change in the value of water saturation coefficient at bottomhole of production well for an unlimited and closed deposit is determined. It is shown that an increase in water cut coefficient of a production well is possible only for a closed formation. To determine coefficient of water saturation in a closed deposit, a differential equation with variable coefficients is obtained, an iterative solution method is proposed. In the element of the five-point system, oil-saturated zones not covered by development were identified. For channels of low filtration resistance, conditions for their location in horizontal and vertical planes are established. It is shown that, at maintaining formation pressure, there is an isobar line in formation, corresponding to initial formation pressure, location of which determines direction of fluid crossflow rates. Intensity of crossflows affects application efficiency of hydrodynamic, physical and chemical, thermal and other methods of enhanced oil recovery.
-
Date submitted2019-03-13
-
Date accepted2019-09-19
-
Date published2020-02-25
Specifying the technical state limit value of the pump pulp without disassembling
The northern part of the territory of the Republic of Sakha (Yakutia) is rich in vast deposits of diamonds. These deposits are developed by the mining company “Almazy Anabara”, which is engaged in the extraction of diamonds at seasonal processing plants using various technological equipment. One of the key types of equipment is the pulp pump of a foreign company “KETO”. The work of pulp pumps of this company in the enrichment of diamond-containing raw materials is accompanied by intensive hydroabrasive wear of their impellers, the service life of which usually does not exceed three months. In practice, untimely replacement of a worn impeller can lead to emergency breakdowns of sealing elements and bearings, which is explained by super-permissible deflections of the shaft of pumping equipment arising from a significant unbalance of the rotor. The main cause of breakdown of slurry pumps at “Almazy Anabara” seasonal processing plants is the inability to quickly identify their ultimate technical condition, the key sign of which is the maximum wear of the impeller. The seasonal beneficiation plants of “Almazy Anabara” currently need a simple and at the same time reliable diagnostic sign of pulp pumps reaching their ultimate technical state, the identification of which can be quickly performed without disassembling and using complex equipment, which is very important when operating pumping equipment in short wash season on the Far North.
-
Date submitted2018-08-30
-
Date accepted2018-11-06
-
Date published2019-02-22
Tourmaline as an ondicator of tin occurrences of cassiterite-quartz and cassiterite-silicate formations (a case study of the Verkhneurmiysky ore cluster, Far East)
- Authors:
- V. I. Alekseev
- Yu. B. Marin
The research focused on the composition of tourmaline from tin ore deposits and ore occurrences within the Verkhneurmiysky ore cluster in the Amur region. The aim of the study is to determine the indicative signs of tourmaline from cassiterite-quartz and cassiterite-silicate formations. This research is based on the materials of a long-term study of the mineralogy of the Far East deposits, conducted at the Mining University under the scientific supervision of Professor Yu.B.Marin. The relevance of the study involves predicting of tin and associated mineralization. For the first time, SIMS and Mössbauer spectroscopy were used to study tourmaline from this region. We identified the typomorphic characteristics of the tourmaline composition, which are proposed to be used as indicators of tin-ore deposits. Typomorphic characteristics of tourmaline from cassiterite-quartz formation: schorl (Mg/(Mg + Fe) = 0.06) with a high content of Al and K; Fe 3+ /(Fe 3+ + Fe 2+ ) = 0.03; Z Fe 3+ = 1 %; impurities: Nb, LREE (La, Ce, Pr), Be, Bi, F, Li, and Mn; LREE content > 9 ppm; positive Gd anomaly. Typomorphic characteristics of tourmaline from cassiterite-silicate formation: schorl-dravite (Mg/(Mg + Fe) = 0.22) with a high Ca content; Fe 3+ / (Fe 3+ + Fe 2+ ) = 0.17; Z Fe 3+ = 9 %; impurities: Zr, Y, Cr, V, Sn, In, Pb, W, Mo, Ti, HREE, Eu, Sr, Sb, and Sc; the content of Y is > 2 ppm, of HREE is > 3 ppm, Eu is > 0.1 ppm.
-
Date submitted2016-09-06
-
Date accepted2016-11-15
-
Date published2017-02-22
Modelling of fiberglass pipe destruction process
The article deals with important current issue of oil and gas industry of using tubes made of high-strength composite corrosion resistant materials. In order to improve operational safety of industrial pipes it is feasible to use composite fiberglass tubes. More than half of the accidents at oil and gas sites happen at oil gathering systems due to high corrosiveness of pumped fluid. To reduce number of accidents and improve environmental protection we need to solve the issue of industrial pipes durability. This problem could be solved by using composite materials from fiberglass, which have required physical and mechanical properties for oil pipes. The durability and strength can be monitored by a fiberglass winding method, number of layers in composite material and high corrosion-resistance properties of fiberglass. Usage of high-strength composite materials in oil production is economically feasible; fiberglass pipes production is cheaper than steel pipes. Fiberglass has small volume weight, which simplifies pipe transportation and installation. In order to identify the efficiency of using high-strength composite materials at oil production sites we conducted a research of their physical-mechanical properties and modelled fiber pipe destruction process.
-
Date submitted2015-12-27
-
Date accepted2016-02-26
-
Date published2016-12-23
Simulation of rock deformation behavior
- Authors:
- Ya. I. Rudaev
- D. A. Kitaeva
- M. A. Mamadalieva
A task of simulating the deformation behavior of geomaterials under compression with account of over-extreme branch has been addressed. The physical nature of rock properties variability as initially inhomogeneous material is explained by superposition of deformation and structural transformations of evolutionary type within open nonequilibrium systems. Due to this the description of deformation and failure of rock is related to hierarchy of instabilities within the system being far from thermodynamic equilibrium. It is generally recognized, that the energy function of the current stress-strain state is a superposition of potential component and disturbance, which includes the imperfection parameter accounting for defects not only existing in the initial state, but also appearing under load. The equation of state has been obtained by minimizing the energy function by the order parameter. The imperfection parameter is expressed through the strength deterioration, which is viewed as the internal parameter of state. The evolution of strength deterioration has been studied with the help of Fokker – Planck equation, which steady form corresponds to rock statical stressing. Here the diffusion coefficient is assumed to be constant, while the function reflecting internal sliding and loosening of the geomaterials is assumed as an antigradient of elementary integration catastrophe. Thus the equation of state is supplemented with a correlation establishing relationship between parameters of imperfection and strength deterioration. While deformation process is identified with the change of dissipative media, coupled with irreversible structural fluctuations. Theoretical studies are proven with experimental data obtained by subjecting certain rock specimens to compression.
-
Date submitted2014-10-08
-
Date accepted2014-12-11
-
Date published2015-08-25
Modeling of geomechanical processes in ore mass using physically nonlinear model
- Authors:
- A. G. Protosenya
The aim of the article is to develop a method of forecasting the state of stress of the ore mass around excavations for ores of weak and medium strength. The paper presents experimental studies on the deformation of ore samples of low and medium strength in the forging equipment in conditions of volume stress state. A physically nonlinear model is used to describe the deformation process of ore mass. The study of the stress state of physically nonlinear ore mass around excavations of round and valuated cross-sections is performed. Values of coefficients of tangential stress concentrations on excavation contour are found for different types of ore. Solutions to physically nonlinear problems in preparatory excavations in the development of the Yakovlevskiy deposit of rich iron ore using a slicing method are considered. Methods for forecasting the stress state in rock mass around mine excavations can be used to assess their stability in the mining of ore of low and medium strength at the Yakovlevskiy iron ore deposit and in the rock and soil masses.
-
Date submitted2010-07-28
-
Date accepted2010-09-18
-
Date published2011-03-21
Assessment of alluvial gold-bearing raw materials from the permafrost zone for justification of combined geotechnology of gold heap leaching
- Authors:
- S. B. Tataurov
The paper presents results of cryogenetic impact on mineral composition and geotechnological properties of alluvial gold-bearing raw materials of natural and man-made origin. In particular, distinctive features in mineral composition of alluvial deposits are described within the permafrost zone and outside it as well as the nature, mechanisms and peculiar features in reduction of man-made gold amalgams are shown. The results obtained were used to justify the expediency of implementation of the combined heap gold ore leaching technology at alluvial deposits in the permafrost zone, which includes preliminary concentration of coarse, medium and fine gold as well as the gold amalgam.
-
Date submitted2009-09-10
-
Date accepted2009-11-15
-
Date published2010-06-25
Media text substance and culturally significant information extraction
- Authors:
- K. P. Sidorenko
The article deals with interpretation of quotation (intertextual substance) in modern Russian speech and forming didactic principles in innovations aspect. Some practical materials concerning culturally significant information extraction are given.
-
Date submitted2009-09-10
-
Date accepted2009-11-18
-
Date published2010-06-25
Numerical modelling of shear strain near to the crack
- Authors:
- S. E. Mansurova
The behaviour of a material near to a crack is considered at nonlinear shear strain. The plane problem of the nonlinear theory of elasticity in the variation form is solved. Some variants of boundary conditions are used. The numerical results received by a finite element method are presented.
-
Date submitted2009-08-25
-
Date accepted2009-10-24
-
Date published2010-02-01
Geomechanical substantiation of parameters of the fastening of railway tunnels in the conditions of the North Caucasus
- Authors:
- N. A. Belyakov
The article presents the rationale of temporary supports used in the drilling of new mines, which provides for the construction of model projects of reconstruction of old tunnels. Finite-element method analyzed the changes of stress-strain state containing tunnel complex array during the drilling of new mines. Based on the analysis, a number of findings to explore the possibility of reducing the thickness of the permanent support of new mines in tunnel complex - the new tunnel, and transport and drainage culvert.
-
Date submitted2009-08-17
-
Date accepted2009-10-18
-
Date published2010-02-01
Geotechnical engineering and hydrogeological specifics of estimate high-rise buildings construction and operation conditions (in terms of local zone on the right bank of Neva river)
- Authors:
- A. M. Zhukova
In the paper specificity of geotechnical engineering conditions in the local zone of the right river Neva bank are considered. The influence of underground topographies of Pre-Quaternary soils roof formed by paleovalleys on the specificity of engineering geological profile is analyzed. Influence of tectonic faults on physical and mechanical properties of Upper Kotlin clays (Upper Vendian) which it is planned to use as the basis for high-rise constructions is considered. Negative influence of Low Kotlin (Upper Vendian) pressure water-bearing horizon on clay properties in the construction foundation and structural materials is investigated.
-
Date submitted2009-07-09
-
Date accepted2009-09-03
-
Date published2010-04-22
The stress-strain state of the massive of the loose ores in the Yakovlevsky deposit around the minings which were drilled with the combines or with drilling-blast technology
The article presents the consistent patterns of the changes in stress-strain state of the massive by the minings of the first stage of protective overlapping in the Yakovlevsky deposit. The change of the stress-strain condition of the rock massive, which is weaked by the mining was determined by the method of finite elements. The stresses distribution in the massive, the displacement of the contour of the minings, the size of conditional zones of non-linear deformations has been obtained. For stoping passes at the first stage the cutting with combine and application of fastening with the anchors has been suggested.
-
Date submitted2009-07-21
-
Date accepted2009-09-28
-
Date published2010-04-22
The determination of the volume stress-strain conditions of the rock massive with the circular outline mining ensrined with the anchors
- Authors:
- A. G. Protosenya
- N. A. Belyakov
In the article the analysis of consolidating effect from application of the anchor fastening, which using at driving of transport tunnels in the conditions of North Caucasus is produced. The change of the stress-strain condition of the rock massive, which is weaked by the mining of the circular outline is certain with the finite-elements method. On the basis of the executed design the row of graphic dependences, which describes changing of the sizes of limitary areas depending on strength and deformational properties of the rocks. Due to results of the conducted work the direction of further researches is seted.
-
Date submitted2008-10-29
-
Date accepted2008-12-11
-
Date published2009-12-11
Experience in providing the stability of tunnel face and roof during its drivage in proterozoic clays
- Authors:
- V. A. Maslak
Methodology for assessment of state of advance support of face with fiberglass anchors and the working¢s roof – with tube anchors, is given. The results of in-situ experimental observations for efforts in anchors, displacements of excavation and growth of load on the advance supports in its roof are shown.