-
Date submitted2023-07-07
-
Date accepted2023-12-27
-
Date published2024-08-26
Landslide hazard assessment in Tinh Tuc town, Cao Bang province, Vietnam using Frequency ratio method and the combined Fractal-frequency ratio method
Landslides are one of the most frequent natural disasters that cause significant damage to property in Vietnam, which is characterized by mountainous terrain covering three-quarters of the territory. In 17 northern mountainous provinces of the country, over 500 communes are at a high to very high landslide hazard. The main goal of this study was to establish landslide hazard maps and conduct a comparative evaluation of the efficiency of the methods employed in Tinh Tuc town, Cao Bang province. The landslide hazard assessment was carried out in this study using the combined Fractal-frequency ratio (FFR) and the Frequency ratio (FR) methods. The FR method is based on the actualist principle, which assumes that future landslides may be caused by the same factors that contributed to slope failure in the past and present. The FFR method is based on the determination of the fractal dimension, which serves as a measure of the landslide filling density in the study area. Eight landslide-related factors were considered and presented in cartographic format: elevation, distance to roads, slope, geology, distance to faults, land use, slope aspect, and distance to drainage. Determining the area under the receiver operating characteristic curve (ROC-AUC) and verification index (LRclass) was performed to assess the performance of prediction models and the accuracy of the obtained maps. As a result, five zones were identified for the study area, characterized by very low, low, moderate, high, and very high landslide hazards. The analysis of the reliability of the obtained landslide hazard maps using the AUC and LRclass indices revealed that the FFR model has a higher degree of reliability (AUC = 86 %, LRclass = 86 %) compared to the FR model (AUC = 72 %, LRclass = 73 %); therefore, its use is more effective.
-
Date submitted2023-07-25
-
Date accepted2024-05-02
-
Date published2024-08-26
Finite element analysis of slope failure in Ouenza open-pit iron mine, NE Algeria: causes and lessons for stability control
Slope failures in mining engineering pose significant risks to slope stability control, necessitating a thorough investigation into their root causes. This paper focuses on a back analysis of a slope failure in the Zerga section of the Ouenza – Algeria open-pit iron mine. The primary objectives are to identify the causes of slope failure, propose preventive measures, and suggest techniques to enhance stability, thereby providing crucial insights for monitoring slope stability during mining operations. The study commenced with a reconstruction of the slopes in the affected zones, followed by a numerical analysis utilizing the Shear strength reduction method within the Finite element method (SSR-FE). This approach enables the examination of slope stability under both static and dynamic loads. The dynamic load assessment incorporated an evaluation of the vibrations induced by the blasting process during excavation, introducing seismic loading into the finite element analysis. The findings reveal that the primary triggering factor for the landslide was the vibration generated by the blasting process. Furthermore, the slope stability was found to be critically compromised under static loads, highlighting a failure to adhere to exploitation operation norms. The challenging geology, particularly the presence of marl layers where maximum shear strain occurs, contributed to the formation of the landslide surface. The study not only identifies the causes of slope failure but also provides valuable lessons for effective slope stability management in mining operations.
-
Date submitted2022-01-20
-
Date accepted2022-07-21
-
Date published2023-12-25
Tribodynamic aspects of the resource of electric submersible vane pumps for oil production
The operation of electric submersible vane pumps for oil production is accompanied by the presence of solid particles, corrosive substances, asphalt-resin-paraffin deposits in the reservoir fluid, leading to changes in performance characteristics and equipment failures. The reduction of the resource as a result of this is accompanied by an increase in the costs of repair and replacement of equipment. The main processes that negatively affect the failure are the wear of the seals of the working stages, the pump plain bearings and vibration, the level of which can significantly exceed the initial level. A test bench and methodology for testing pump sections for wear in water with an abrasive and simultaneous registration of vibration characteristics have been developed. Two main forms of wear of radial seals have been identified – one-sided and equal-dimensional. The one-sided form of sleeve wear is caused by synchronous shaft precession, whereas the equal-dimensional one is an asynchronous precession, and the vibration level increases with increasing wear. The wear distribution of radial seals along the length of the pump correlates with the shape of the elastic shaft line. The wear of the axial seals does not significantly increase the vibration level. During wear the frequency spectrum of vibrations changes; there occurs a frequency that can serve as a diagnostic sign of ultimate wear of the pump. The calculated dependence of the vibration velocity on the wear of the radial seals of the working stages is obtained, which makes it possible to predict the onset of a failure of functioning.
-
Date submitted2021-11-10
-
Date accepted2022-05-25
-
Date published2022-12-29
Predicting the permeability of the near-bottomhole zone during wave impact
The research reveals that during selection of a method to increase oil recovery it is necessary to take into account rheological features of fluid movement through the formation, effect of capillary forces and heterogeneity of reservoir properties of the productive formation in thickness and along the bedding. Low-frequency wave impact, which is used to increase production in oil fields, is considered. At low-frequency impact new fractures appear and existing fractures in rocks increase in size. The greatest increase in porosity and permeability of rocks occurs at an impact frequency up to 10 Hz. Dynamics of oscillation amplitude during wave's movement in saturated porous medium is studied in the paper: essential attenuation of amplitude occurs at distance up to 1 m from borehole axis. With increase of frequency from 1 to 10 Hz the intensity of amplitude's attenuation decreases. The technology was tested on a well in Perm region (Russia). The actual permeability value was 50 % higher than the predicted value. According to the results of hydrodynamic investigations processing, it was noted that the greatest increase of permeability took place near the wellbore, while away from the wellbore axis permeability remained almost unchanged. In order to refine the mathematical model for prediction of wave impact on rock permeability it is necessary to take into account interconnection of pore space structure, change of adhesion layer, as well as to study transfer of particles during vibration.
-
Date submitted2021-09-22
-
Date accepted2021-11-30
-
Date published2021-12-27
Possibilities for creating Russian high-tech bottomhole assembly
Development of high-tech well electronic measuring systems is aimed at creating modern equipment: telemetry, well geophysical measurement equipment, the architecture of which is divided into basic (with measurement channels for gamma logging and inductive resistance) and advanced (with radioactive, acoustic, magnetic resonance and thermobarometric measurement channels, including azimuthal methods of investigation). Over-the-bit measurement modules, rotary steerable systems are being developed and channels for transmitting data to the surface are being improved. Vice versa, specialized surface equipment with highly integrated software is being created. Different measurement modules are manufactured by different companies, which creates uncertainties in the possibility of interfacing the manufacturers' measurement modules into a single well measurement system. The article presents an analysis of the readiness of Russian oil service companies to produce well and surface equipment for drilling Russian directional oil and gas wells, meeting modern requirements for accuracy, lifetime and operating conditions. The possibility of creating a fully Russian well high-tech equipment and the required resources, risks and measures to mitigate them when creating a modern well measurement system are considered.
-
Date submitted2020-05-15
-
Date accepted2020-06-12
-
Date published2021-06-24
One of the ways to increase the durability of the sectional pump balancing ring
- Authors:
- Nikolai P. Ovchinnikov
The article presents the results of scientific research aimed at struggling the adhesive wear of parts of sectional pumps balancing ring, where the drainage units pumping equipment of the Russian Federation underground kimberlite mines was used as an object of research. It has been theoretically proven and experimentally confirmed that if there is data on the total operating time of a sectional pump in transient modes per day, using the constructed regression model, it is possible to calculate with high accuracy the average operating time of its balancing ring unit to failure. The constructed regression model is applicable only to sectional pumps of drainage units of underground kimberlite mines in the Russian Federation. It is possible to increase the durability of the balancing ring by reducing the acceleration and deceleration time of the sectional pump; for safe operation, it should be at least 10 s. Pilot tests carried out indicate the effectiveness of the proposed method for prompt identification of the critical axial displacement of the sectional pump rotor through the vibration of the discharge tube. The introduction of this method will reduce the cost of repair work to restore the performance of parts of the hydraulic foot to a minimum.
-
Date submitted2019-10-30
-
Date accepted2019-11-23
-
Date published2020-02-25
Methodology for determining the parameters of drilling mode for directional straight sections of well using screw downhole motors
- Authors:
- Vladimir S. Litvinenko
- M. V. Dvoinikov
Article presents results of study on possibility of increasing the efficiency of drilling directional straight sections of wells using screw downhole motors (SDM) with a combined method of drilling with rotation of drilling string (DS). Goal is to ensure steady-state operation of SDM with simultaneous rotation of DS by reducing the amplitude of oscillations with adjusting the parameters of drilling mode on the basis of mathematical modeling for SDM – DS system. Results of experimental study on determination of extrema distribution of lateral and axial oscillations of SDM frame depending on geometrical parameters of gerotor mechanism and modes ensuring stable operation are presented. Approaches to development of a mathematical model and methodology are conceptually outlined that allow determining the range of self-oscillations for SDM – DS system and boundaries of rotational and translational wave perturbations for a heterogeneous rod with an installed SDM at drilling directional straight sections of well. This mathematical model of SDM – DS system's dynamics makes it possible to predict optimal parameters of directional drilling mode that ensure stable operation of borehole assembly.
-
Date submitted2019-03-31
-
Date accepted2019-08-25
-
Date published2020-02-25
Cascade frequency converters control features
The structures of systems with high-voltage cascade frequency converters containing multi-winding transformers and low-voltage low-power converters connected in series at each output phase of the load are considered. Low-voltage blocks contain three-phase diode or active rectifiers, DC capacitor filters, single-phase stand-alone voltage inverters and block disconnecting devices in partial modes (in case of failure when part of the blocks are disconnected). The possibilities of operation of cascade converters are determined, equations for correcting tasks to units in partial modes are given, tables of correction of tasks with estimates of achievable load characteristics are proposed. The results of experiments on the model of a powerful installation with a cascade frequency converter are presented, confirming the possibility of ensuring the symmetry of the load currents when disconnecting part of the blocks and the asymmetry of the circuit.
-
Date submitted2019-05-05
-
Date accepted2019-07-03
-
Date published2019-10-23
Scraper Face Conveyors Dynamic Load Control
- Authors:
- E. K. Eshchin
The task of controlling the dynamic loading of scraper face conveyors (SC) is considered and the unsatisfactory state of loading of mechanical and electrical components of the SC is recorded. The possibility of the appearance of a self-oscillatory nature of the entire system load due to the peculiarities of the movement of the traction chain along the lattice frame of the SC is indicated. The property of the system is noted – the cyclic nature of the loading of the circuit during movement, which causes energy exchange processes between the mechanical and electromotive components of the conveyor (when using the head and tail electric drives) through the common cable network of the power supply system of the SC. A high level of dynamic loading of the electromechanical system causes the problem of eliminating the self-oscillating operating mode of the SC that generates it which is proposed to be solved by changing the angular rotation speeds of the SC drive sprockets. Angular speeds can be changed by applying frequency control of asynchronous electric motors. The efficiency of setting the frequency of electric motor stator currents of the head and tail drives of the conveyor is established in proportion to the frequency of rotors rotation to eliminate self- oscillating modes of operation in the main operating mode. The possibility of reducing the starting shock values of the electromagnetic moments of electric motors is considered. The results of the calculation of the start-up and liquidation of the self-oscillating operating mode are presented on the example of the scraper face conveyor Anzhera-34. The results of calculations of the start-up modes and the main operational transportation of coal in an uncontrolled mode of operation and after the introduction of control are compared, based on which it is concluded that it is advisable to use active control of the dynamic loading ofSC.
-
Date submitted2019-03-13
-
Date accepted2019-05-18
-
Date published2019-08-23
Improving the Operation of Pump-ejector Systems at Varying Flow Rates of Associated Petroleum Gas
- Authors:
- A. N. Drozdov
- Ya. A. Gorbyleva
Application of pump-ejector systems for the utilization of associated petroleum gas reduces the negative environmental impact of its flaring, and also allows the implementation of a promising method of water-gas stimulation of the formation, which effectively increases oil recovery. Equally feasible is the use of pump-ejector systems in the operation of oil wells with a high gas factor, low bottomhole pressures to increase production rates and increase the turnaround period. A significant change in the flow rate of associated petroleum gas over time is a serious problem for the efficient operation of pump-ejector systems for the utilization of associated petroleum gas. To ensure the rational operation of the pump-ejector system under the condition of a variable flow rate of associated petroleum gas, experimental studies of a liquid-gas ejector characteristics were carried out. The article presents the results of the research, obtained pressure-energy characteristics of the investigated jet apparatus at various values of the working stream pressure before the ejector nozzle. The possibility of adapting the operation of pump-ejector systems to changes in the flow rate of the pumped gas, regulated by the working pressure and fluid flow rate through the nozzle is revealed. To successfully change the operation of the pump-ejector system, the possibility of frequency regulation of the pump shaft's rotation at changing gas flow rates in a small range of values is considered. With a large difference in the values of the possible flow rate of associated petroleum gas, it is recommended that frequency regulation should be supplemented by periodic short-term operation. The possibility of increasing the efficiency of the pump-ejector system when using salt solutions with a concentration that contributes to the suppression of bubble coalescence is noted.
-
Date submitted2018-09-04
-
Date accepted2018-11-18
-
Date published2019-02-22
Operation experience of centrifugal single-stage pumps in «ALROSA» Joint Stock Company
- Authors:
- N. P. Ovchinnikov
When mining diamond-bearing raw materials and further extracting diamonds from it in the joint-stock company ALROSA, which is a city-forming enterprise in the north-east of the Russian Federation, various pumping equipment is used, in particular, centrifugal single-stage pumps. In the present work, it is noted that the least reliable in terms of absence of failures of centrifugal single-stage pumps used in the joint-stock company ALROSA are the impellers, seals and bearing assemblies. Using linear correlation and regression analysis, it was found that the durability of the seals and bearing assemblies of the investigated pumps largely depends on the durability of their impellers. In the course of research, it was found that unbalancing the pump rotor due to excessive hydroabrasive wear of the impeller also leads to deformation and fracture of the shaft. In general, residual deformations and destructions are characteristic of the shafts of domestic pulp pumps of GrAT, GrT and Gr types. The most loaded sections of shafts of centrifugal single-stage pumps are installed. The most effective from the point of view of application among the pulp (ground, slurry and sand) pumps are pulp pumps of the Finnish company «Metso». When working on highly mineralized water (brines), the «X» type pumps have proven to be the best among centrifugal single-stage pumps.
-
Date submitted2017-09-03
-
Date accepted2017-11-04
-
Date published2018-02-22
Development of sensorless vector control system for permanent magnet synchronous motor in Matlab Simulink
- Authors:
- V. Ya. Frolov
- R. I. Zhiligotov
In last 20 years segment of electric drives with permanent magnet synchronous motors has increased. This type of motors has better technical characteristics compared to induction motors, but has problems in actual implementation, one of which is the requirement of rotor position data. It is possible to implement with use of sensors or without them by means of motor state observer. The paper describes problems of sensorless vector control system for permanent magnet synchronous motors. The vector control system with state observer for permanent magnet synchronous motors is described. Synthesis of sliding mode observer for rotor speed and position is presented. The algorithm is implemented by development of model in Matlab Simulink environment with support by Texas Instruments processors support blocks. Experimental comparison of results of rotor angle state calculation and the data obtained by rotor position sensors was conducted. Research objective is a development of control algorithm, which has required precision for calculation of rotor start angle, high range of speed regulation and resistance to drift of motor parameters.
-
Date submitted2016-09-01
-
Date accepted2016-11-05
-
Date published2017-02-22
Research on technical and technological parameters of inclined drilling
- Authors:
- M. V. Dvoinikov
An analysis of operational capabilities of inclined drilling equipment and technology is presented. Two options of rotary drilling are reviewed as technical and technological solutions, facilitating construction of wells with difficult profiles. The first option implies that the driver unit of the drill bit is represented by downhole drilling motor, the second one utilizes sophisticated rotary steerable systems. Practical results of drilling wells with difficult profiles are presented. A quality assessment of drilling is provided through the example of comparing designed and actual trajectories, using different driver units for the drill bit, as well as properties of surrounding rocks, rheology of the drill fluid and other characteristics of dynamically active systems. A range of rotation speed has been determined that allows rotary steerable systems to have minimal oscillation amplitude of the bottom-hole assembly. Analysis of investigation results showed that the main source of oscillations is linked to bending and compressing stresses, caused by well deviations as well as rigidity of the drilling tool. In effect, in the bottom-hole assembly occur auto-oscillations, making it impossible to correct azimuth and zenith angles. Alteration of rigidity in the bottom part of the tool and drilling parameters, implying reduced rotation speed of the drill string and regulation of drill bit pressure, can partially solve this problem, though increase in rotation speed is limited by technical characteristics of existing top drive systems.
-
Date submitted2015-10-06
-
Date accepted2015-12-18
-
Date published2016-08-22
New technology of dry benefication of fly ash from coal power plants using applied mineralogy techniques
- Authors:
- V. A. Arsentev
- E. L. Kotova
The existence of environmental and strategic need to process dumps and slagheaps of coal mining enterprises of Russia and foreign countries results in reviewing the potential of using fly ash as a technogenic mineral resource. Comprehensive studies of substance composition of fly ash from coal power plants make it possible to define rational further ways of utilizing that mineral resource substantiating the scheme of its technological secondary processing. In view of the numerous environmental problems stemming from the techniques of wet benefication and processing of that mineral resource, a technology is suggested of dry cleaning of fly ash from thermal coal power plants. Studies were carried out using a number of samples of fly ash from various power plants. The suggested criteria are used to discriminate the compounds of fly ash and quantitative and qualitative composition of particulate matter is assessed. Studies of substance composition of fly ash samples has demonstrated that the concentration of non-combusted carbon in them varies from 5 to 20 %. The principal technological procedure of cleansing in our studies was a combination of magnetic and electric separation of ash in the state of vibrational pseudo-liquefaction. It enables one to increase the throughput capacity and selectivity of the cleansing process significantly. In the result of such cleansing a stable mineral fraction is produced that contains 0.5-2.5 % of carbon, so that the purified mineral fraction can be used as a construction binding agent.
-
Date submitted2015-08-03
-
Date accepted2015-10-06
-
Date published2016-04-22
Technical and technological solutions to ensure stability of downhole drilling motors
- Authors:
- M. V. Dvoinikov
- Yu. D. Muraev
The article shows research analysis of engineering and technological solutions that aimed at improving the efficiency of drilling wells using optimization of dynamic of work downhole drill-ing motors. As the technical solutions that reduce vibration, considered two options of construc-tion of the power section. A first embodiment involves the production of a hollow rotor which can reduce its moment of inertia. The second solution is the production of modular rotor, which are changing the eccentricity (misalignment) of rotating parts of the engine. The research of fluctuations throughout the length of the power section of the working bodies and the spindle of the engine, taking into account changes in its energy characteristics has been con-ducted to ensure stable operation of the engine in a well, identifying optimal loading parameters. Indicators of shaft speed ensuring minimum vibration amplitude of the engine has been Iden-tified. Optimal speed range of the rotor to prevent buckling of the BHA and to sustain its operation is shown to be between 15-20 % of the frequency of the engine at idle. The maximum reduction in speed during the drilling process should not exceed 30 % by conducted research.
-
Date submitted2015-08-18
-
Date accepted2015-10-06
-
Date published2016-04-22
Energy- efficient control of asynchronous motor drive with current refinement of the loss minimum on the basis of fuzzy logic
- Authors:
- O. B. Shonin
- V. S. Pronko
Currently, asynchronous electric drive on the basis of semiconductor frequency converters is widespread because of the relative simplicity and reliability of the design, the use of digital control systems, providing the accuracy and flexibility of process control, which allows for a significant increase in product quality, reduction in energy consumption and improvement of the enterprise profitability. In spite of these advantages, the problem of ensuring high energy efficiency of the drive in wide range of its operational modes is still not solved in full scale. The paper is devoted to the reduction of losses in the asynchronous drive on the basis of en-ergy-saving control algorithms that aim to ensure the desired mode of the driven mechanism while minimizing losses in copper and steel of the motor. On the basis of the motor model, taking into account magnetic losses, dependences of losses in the copper and steel, as well as the total loss from the absolute slip have been derived for different operating points of the drive. The optimal values of the absolute slip for different speeds of the rotor have been obtained for use in the con-trollers ensuring operation of the drive at maximum efficiency, highest power factor and minimum of the stator current. For minimizing the losses in the drive when changing the motor parameters it has been offered the combined method based on the method of loss model and iterative method of searching the minimum of power consumption. The effectiveness of the proposed control system using fuzzy logic is confirmed by comparing the graphs of losses and efficiency, obtained at using a traditional control law and the optimal control law.
-
Date submitted2014-12-27
-
Date accepted2015-03-01
-
Date published2015-12-25
Minimization of energy losse when starting a variable frequency drive through application of a genetic algorithm of optimization
- Authors:
- O. B. Shonin
- V. S. Pronko
In the face of energy lack and rising energy prices one of the priorities of current researches is to improve energy efficiency of electric drives, which are widely used in modern industrial plants. Existing methods of minimizing losses are mainly designed for stationary regimes. At the same time, the development of algorithms for reducing losses in transient and in particular starting conditions is given little attention. Due to the high complexity of the description of the multivari-ate dynamic processes determining the optimal control laws is advantageously to be carried out us-ing stochastic optimization methods. The work seeks to substantiate the optimal starting character-istics of an asynchronous drive based on a genetic algorithm. A feature of the proposed method of optimization is the use of multiple simulation experiments to find start-up characteristics which provide a minimum energy loss. Automation of the search is performed using the developed pro-gram, which includes a module of a genetic algorithm and a module for interfacing with the elec-tric model in the MATLAB/Simulink environment. The program allows choosing the parameters of the genetic algorithm along with controlling the process of optimization. Application of the proposed method allowed obtaining the optimal starting characteristics «voltage – frequency» in a tabular form with consequent linear approximation of the data. Increase in efficiency due to the proposed start up law has been confirmed by comparing the simulation re-sults under conditions of using a traditional linear characteristic and derived optimal law. The es-timation of losses reduction has been carried out at the drive load of different kind in a wide range of its variation.
-
Date submitted2014-10-09
-
Date accepted2014-12-26
-
Date published2015-08-25
Improving the precision of manufacturing power hydraulic cylinders of powered roof supports based on a vibration-damping tooling system
- Authors:
- V. V. Maksarov
- Yu. Olt
The article deals with a new system of a vibration-damping tool, the effect of which is achieved by a combination of the multi-layer principle and the use of anisotropic properties of sheet metal. Operation of such tool systems in turning operations can reduce high-frequency vibra-tions arising in the process of cutting due to the ordered disorientation of anisotropic plate texture of a multilayer modular tool holder that allows you to efficiently dissipate oscillatory wave energy at the boundary of transition between the plates of the tool holder. This method allows increasing the resistance of the tool cutting edge significantly and expanding the technological capabilities for the effective selection of cutting modes to ensure compliance with requirements for dimensional and geometric accuracy, quality of processed surfaces of powered roof supports, hydraulic units, mining machinery and equipment.
-
Date submitted2014-09-01
-
Date accepted2014-11-13
-
Date published2015-06-26
Development of the stepper motor control system in steam generating units
- Authors:
- A. L. Lyashenko
- I. M. Pershin
The article deals with the design and operation of a steam generating unit through the example of the reactor core RBMK-1000 (High Power Channel-type Reactor). It contains the description of the equipment being a part of the multiple forced circulation circuits (MFCC), which form the reactor. Careful consideration is given to the process of controlling the coolant flow in the reactor fuel channels via shut-off control valve (SOCV) and the necessity of its (the process) automation. The problem of SOCV automatic control system synthesis is formulated and solved. The possibility of using a device with extended frequency response (EFR) for a frequency response analysis of distributed parameter systems (DPS) is considered. The problem of developing a method for calculating the settings of the distributed PID-controller is formulated and solved. Software for the simulation of thermal field in the reactor core is developed.
-
Date submitted2014-09-19
-
Date accepted2014-11-09
-
Date published2015-06-26
Methods of evaluation of vibrational activity of power plants using the similarity theory and dimensional analysis
- Authors:
- O. K. Bezyukov
- O. V. Afanaseva
The level and the nature of changes of vibrational parameters are one of the most important indicators of the technical state of diesel engines as the most sensitive to various derivations from nor-mal technical condition. This article discusses methods of assessment of vibration activity of engines generated by gasdynamic and mechanical factors. The possibility of using the methods of similarity theory and dimensional analysis in the development of new and improvement of existing methods of vibrational diagnostic of internal combustion engines, which significantly increases the informativeness of vibrational diagnostic of the engine.These criteria allows to simulate and study the impact of gas dynamic processes in combustion of fuel on the vibration of internal combustion engines, consider the impact on the relocation of the piston on the vibration activity of diesel and dependence of vibration velocity on the density of the material and to carry out measurements of vibration velocity on the surface of the cylinder block. The methods, that authors propose, are the basis for methods of determining of vibrational activity of dieselengines, are adequate to complexity of this process and to possibilities of measurement equipment.
-
Date submitted2010-07-15
-
Date accepted2010-09-13
-
Date published2011-03-21
Experimental setup for research Influence of vibromechanical treatment on mechanical properties of welded joints
- Authors:
- O. F. Khafizova
- V. I. Bolobov
The description of developed experimental setup for welding product that made of pipeline steels with application of applying vibration with intended frequency approximating to natural-vibration frequency of welded construction unit of pipelines during the welding cycle is presented.
-
Date submitted2010-07-06
-
Date accepted2010-09-14
-
Date published2011-03-21
Electromechanical processes in electric drives of mountain equipment on the basis of the synchronous electric motor
- Authors:
- A. O. Sviridenko
The description is given and the function chart of the bench installation is resulted, allowing to reproduce static and dynamic modes of adjustable electric drives of an alternating current. The modes considered during experimental researches of the electric drive on the basis of the synchronous electric motor, working in a mode of ventilniy electric motor are listed. Conclusions are drawn on character of course of dynamic modes, comparison of the electric drive to the synchronous electric motor and the electric drive of a direct current with the subordinated regulation is given.
-
Date submitted2010-07-20
-
Date accepted2010-09-14
-
Date published2011-03-21
The physical breadboard model of dynamically counterbalanced drilling string with swinging movement with the asynchronous electric drive powered by inverter laboratory experimental researche
- Authors:
- V. V. Ivanik
The laboratory experimental stand for research of the asynchronous resonant electric drive on a physical breadboard model of dynamically counterbalanced drilling string is developed. The asynchronous electric drive with swinging movement the autoresonant oscillation mode is realized.
-
Date submitted2010-07-08
-
Date accepted2010-09-02
-
Date published2011-03-21
The autoresonant asynchronous electric drive of dynamically counterbalanced drilling string on carrying cable with swinging movement fluctuations amplitude stabilization
- Authors:
- E. A. Zagrivnyi
- V. V. Ivanik
The algorithm of resonant fluctuations amplitude stabilization of dynamically counterbalanced drilling string on carrying cable with swinging movement of jackbit is developed. Imitating modeling of the resonant asynchronous electric drive with swinging movement of jackbit with the frequency converter in various operating modes is resulted.
-
Date submitted2010-07-26
-
Date accepted2010-09-14
-
Date published2011-03-21
Algorithm of control of the electric drive with ventilniy electric motor and the converter of frequency with the active rectifier
- Authors:
- A. P. Emelyanov
- A. O. Sviridenko
Advantages of application of the active rectifier as a part of converters of frequency for powerful drives with ventilniy electric motors are considered. The mathematical description of the processes proceeding in a power part of the active rectifier is given. The scheme of a drive with a vector control system with the gage of position of a rotor and the active rectifier is presented, schedules of power consumption and a current by a drive with the active rectifier are resulted.