-
Date submitted2023-12-07
-
Date accepted2024-11-07
-
Date published2025-04-07
Determination of the tangential component of cutting resistance during frozen sedimentary rock cutting using blocked, deeply blocked and cell cutting methods
Due to the insufficient accuracy of existing studies of frozen sedimentary rock cutting process for practical calculations, the article solves the problem of determining the tangential component cutting resistance for blocked, deep blocked and cell cutting, which are currently the most commonly used methods in earthmoving equipment. The cutting tool and rock mass force interaction is considered from the point of view of the emerging stresses, which act on the separated chip element. The analytical dependences for determining the tangential component of cutting resistance were obtained. The numerical explanation of the choice of cell cutting in relation to blocked and deeply blocked cutting is given. For all three methods of cutting, under equal geometrical parameters of the cutting tool and the physical and mechanical properties of the frozen rock, the numerical value of the tangential component of cutting resistance is obtained. The comparison of the cutting resistance estimated values has shown that cell cutting requires relatively less energy and is preferred during the process of frozen sedimentary rock excavation. During field and laboratory investigations with the use of a multi-purpose cutting stand, a sufficient convergence of the analytical statements with the physics of frozen sedimentary rock cutting process was established. The results of the research allow a more reasonable approach to the adjustment of existing methods for determining the required tractive force and power for the drive of an excavation machine, and, therefore, to the actual efficiency and profitability of work.
-
Date submitted2022-03-24
-
Date accepted2022-07-21
-
Date published2022-12-29
A probabilistic study on hole cleaning optimization
- Authors:
- Seyyed Shahab Tabatabaee Moradi
Hole cleaning is considered as one of the most important drilling fluid functions. An efficient hole cleaning ensures a reliable well drilling practice with minimum troublesome problems. In this study, two main steps of hole cleaning, i.e., cuttings removal from under the bit and cuttings transport to the surface are discussed based on the drilling data of a shale formation. The traditional models for optimization of each step are presented. As the models require variety of input data, which are usually subjected to some extent of errors and uncertainties, the output of the model is also an uncertain parameter. Using Monte Carlo simulation, a simple probabilistic study was conducted to quantify the certainty level of the obtained results. Based on the result of this study, it is shown that for the proposed well, a good hole cleaning is expected. However, a more reliable decision for further hole cleaning optimization should be made considering the results of uncertainty analysis.
-
Date submitted2022-05-12
-
Date accepted2022-09-15
-
Date published2022-12-29
Problem solution analysis on finding the velocity distribution for laminar flow of a non-linear viscous flushing fluid in the annular space of a well
- Authors:
- Vasiliy I. Nikitin
Modern drilling fluids are non-linear viscous media with an initial shear stress. In classical scientific works on hydromechanical modeling of drilling fluids motion in pipes and annular channels the Shvedov – Bingham approximation and Ostwald – de Waale power-law model were used, which did not fully account for behavior of technological fluids in a wide range of shear rates. This article presents a numerical solution for a mathematical model of drilling fluid motion of the three-parameter Herschel – Bulkley rheological model in the annular space of the well. The Herschel – Bulkley model in the rheological equation takes into account the presence of initial shear stress and a tendency for viscosity to change with shear rate, which distinguishes it from the Ostwald – de Waale and Shvedov – Bingham models. The target function in solving the equation of motion is the velocity distribution in the radial direction of the upward flow of the flushing fluid. The analysis of obtained solution is based on the theory of velocity profile influence on quality of cuttings removal during wellbore cleaning. Due to peculiarities of mathematical statement of the task, which supposes necessity of differential equation of motion solution, Wolfram Mathematica computational software has been used as a calculation tool. The analysis of numerical solution allowed to draw conclusions about the possibility of its application in evaluation of velocity profile when drilling fluid moves in annular space of the well. The possibility for application of modified excess coefficient as a relative quantitative parameter for evaluation of velocity profile uniformity was substantiated.
-
Date submitted2022-04-14
-
Date accepted2022-07-21
-
Date published2022-11-03
In-situ leaching of molybdenum and uranium by percarbonate and chloride-hypochlorite solutions
In-situ leaching of molybdenum and uranium is becoming an increasingly common process. The features of the material composition of ores, leading to a decrease in their filtration properties, were considered. Activation leaching with leaching solutions that have undergone electrophotochemical activation before contact with the ore mass were studied. Activation preparation of leaching solutions promotes the synthesis of clustered water molecules with collectivized protons and hydroxyl ions, as well as active forms of oxygen and hydrogen. Cell leaching of molybdenum from mature tailings of the Shakhtaminsk deposit was studied experimentally. After pre-oxidation with an active carbonate solution, a model borehole leaching was carried out with a chloride-hypochlorite solution. Molybdenum extraction on resin a was 85 % in 30 days. Experiments on the percolation leaching of uranium from the ores of the Uchkuduk and Sugraly deposits confirmed the potential possibility of a significant increase in the extraction of uranium by electrophotoactivated percarbonate solutions relative to aqueous solutions of sodium and ammonium carbonate. When leaching with carbonate solutions without an additional oxidizing agent, the extraction of uranium from the Sugraly deposit ore sample was 52 and 59 % (sodium carbonate and ammonium carbonate). The use of hydrogen peroxide as an oxidizing agent made it possible to achieve 87-88 % extraction into pregnant solutions in 21 days without pre-oxidation. The performed studies confirm the processing capability of extracting uranium and molybdenum by percolation leaching in columns and borehole leaching.
-
Date submitted2021-12-19
-
Date accepted2022-07-21
-
Date published2022-11-10
Increasing the content of coarse fractions in the mined coal mass by a combine using paired cuts
The main volume of coal is mined underground using shearers. In modern shearers, auger actuators are mainly used, which are distinguished by the simplicity of design, manufacturability and reliability. However, in the process of separating coal from mass by cutting, the yield of fine grades is 40-50 % of the total production volume. Therefore, the search and development of technical solutions that provide an increase in the yield of large fractions in the process of coal mining with auger shearers is an urgent task. Traditionally, this problem is solved by increasing the thickness of the slices, which is achieved by installing cutters with a larger radial reach and increasing the shearer feed rate. An unconventional way to increase the cross section of slices by forming energy-efficient paired and group slices with mutual superposition of stress fields in the mass from the action of neighboring cutters is considered. The results of modeling the process of cutting coal confirm that an increase in the efficiency of destruction of the rock mass by the cutters of the auger executive bodies of the shearer can be achieved by a complex technical solution, including the formation of paired cuts and combined stress zones in the rock mass. As a result, the output of large fragments when cutting with paired cutters increases by 1.3-1.8 times compared with cutting with a single cutter.
-
Date submitted2020-05-13
-
Date accepted2021-05-21
-
Date published2021-09-20
Increasing the efficiency of technological preparation for the production of the manufacture components equipment for the mineral resource complex
An increase of components production for the equipment intended for oil and gas production is a key factor for analyzing existing technological processes and searching for new technological solutions to improve the efficiency of the production process and the quality of components. The article presents a simulation model designed to determine the rational technological processing parameters for the production of the “Centralizer shell” part. The basis for optimizing the working cycle of a production line is synchronization based on the principle of proportionality, which involves equalizing the duration of all technological operations with the rhythm of the production line. Synchronization of technological operations on the production line is carried out by choosing rational cutting parameters for each technological transition (cutting speed, feedrate, number of working passes). The “Centralizer shell” part is made of titanium alloy VT16, which has high strength, corrosion resistance and ductility. For the part under consideration, the permissible values of the cutting parameters were determined based on the calculation of the total processing error, as well as the frequency of replacement of the worn cutting tool. The simulation model described in the article made it possible to increase the efficiency of the production process due to the synchronization of technological operations and the search for rational technological parameters, as well as to improve the manufacturing quality of the “Centralizer shell” part by analyzing the processing error at various parameters of the technological process.
-
Date submitted2020-07-04
-
Date accepted2021-03-29
-
Date published2021-09-20
Transition between relieved and unrelieved modes when cutting rocks with conical picks
In the modern theory of rock cutting in production conditions, it is customary to distinguish two large classes of achievable cutting modes – relieved and unrelieved. The kinematics of rock-breaking machines in most cases determines the operation of the cutting tool in both modes in one cycle of the cutting tool. The currently available calculation methods have been developed for a stable, usually unrelieved cutting mode. In this article, the task is set to determine the conditions for the transition between cutting modes and the modernization of the calculation method for determining the forces on the cutting tool. The problem is solved by applying methods of algebraic analysis based on the search for the extremum of the force function on the cutter, depending on the ratio of the real cut spacing to the optimal spacing for the current chip thickness. As a result of solving the problem, an expression is obtained for determining the chip thickness, for which, at the specified parameters, the transition between the relieved and unrelieved cutting modes is provided. The obtained result made it possible to improve the method of calculating the forces on the cutting tool in the areas of the cutter movement with relieved cutting.
-
Date submitted2019-11-04
-
Date accepted2020-01-12
-
Date published2020-10-08
PDC cutter pressure on plastic-brittle rock in the process of its destruction
- Authors:
- Oleg B. Trushkin
- Hamzja I. Akchurin
Presently, there are no methods for calculating the parameters of the drilling practices with rock-cutting tools equipped with polycrystalline diamond composite (PDC cutters). To create such a method requires the studying their work. The article presents the results of bench studies of the PDC cutters in the process of a rock sample breakdown when reproducing the actual layout of the cutters on the working surface of the bit. An important parameter of PDC cutters operation, which is necessary for the bit load analysis, is the pressure of the cutters on the rock during its breakdown. The total pressure of a cutter on the rock can be broken into two mutually perpendicular components: the forcing pressure and the cutting pressure. It is proposed to evaluate the PDC cutters loading at breakage of rocks of different hardness using relative values of forcing and cutting pressures, which are calculated relative to the yield strength of the rock by the die. It is established that the variability of the average relative pressures of forcing and cutting is significantly influenced by drifting per bit turnover and the radius of the cutter on the bit. The dependences of the maximum relative pressures of PDC cutters at the plastic-brittle rock breakdown on the drifting per bit turnover and the radius of the cutter location on the bit are obtained. It has been established that when drifting up to 0.4 mm per turn, the main mechanism of breakdown is cutting, and with the increase of the breakdown depth, the process of forcing becomes decisive.
-
Date submitted2019-07-06
-
Date accepted2019-08-25
-
Date published2019-12-24
Improving the efficiency of technological preparation of single and small batch production based on simulation modeling
Technological preparation of production is an integral stage of the production process, which is characterized by high complexity, which is largely felt in the conditions of single and small-scale types of production. The effectiveness of technological preparation of production is increased through automation with the use of simulation modeling. The objective of the study is to develop a simulation model that allows you to determine a rational version of the process for processing a batch of parts. The simulation model described in the article allows to analyze the production schedule of the enterprise, build processing routes, evaluate options for using various types of workpieces and technological equipment, determine the acceptable values of cutting conditions, and choose a rational variant of the technological process of processing a batch of parts. The developed simulation model is based on the principles of modular technologies, the part is considered as a combination of individual elementary surfaces. Each elementary surface contains information about the technological processing route, technological equipment and the type of technological equipment used in its manufacture, cutting conditions and the size of the allowance for each processing stage. The rational choice of the technological process is selected on the basis of multicriteria analysis according to three criteria: the value of variable costs, the production time of a batch of parts and the value of the processing error. The analysis of these criteria is made and the parameters that have the greatest impact on their value are determined. The developed classification of surface elements is described: design elements, technological elements, basic elements, as well as a mathematical model based on which the calculation of the values of the criteria for choosing a rational option.
-
Date submitted2019-07-23
-
Date accepted2019-09-19
-
Date published2019-12-24
Estimation of abrasiveness impact on the parameters of rock-cutting equipment
Development of equipment, which provides access to underground mineral deposits and their extraction, requires the use of all the accumulated experience and advanced scientific research in the area of mechanical rock cutting. The most important issues of using mechanical rock cutting tools are their wearability and consumption, which have an impact on technical and economic indicators of project efficiency. The paper describes Russian and foreign practices of estimating tool wear resistance, expressions to determine critical cutting speed, methods to evaluate tool consumption. It is demonstrated that wearability of mechanical tools and associated effects are to a large extent defined by rock abrasiveness. It is highlighted that in Russia the index is calculated using Baron-Kuznetsov method, which is briefly described in the paper. In many countries with a highly-developed mining industry, rock abrasiveness is estimated with a Cerchar Abrasiveness Index (CAI), recommended by the International Society for Rock Mechanics. Its description is also presented in the paper.
-
Date submitted2019-04-28
-
Date accepted2019-06-28
-
Date published2019-10-23
Determination of Optimal Fluorine Leaching Parameters from the Coal Part of the Waste Lining of Dismantled Electrolytic Cells for Aluminum Production
- Authors:
- N. V. Nemchinova
- A. A. Tyutrin
- V. V. Somov
When aluminum is obtained by electrolysis of cryolite-alumina melts when the baths are sent for capital repairs, a solid technogenic product is formed – waste lining of electrolytic cells (WLEC). The volume of formation of WLEC is 30-50 kg per 1 ton of aluminum. Currently, it is mainly stored at landfills near industrial enterprises, causing harm to the environment. However, this technogenic raw material contains valuable components (fluorine, aluminum, sodium) that can be extracted to produce fluoride salts, which are in demand during the electrolytic production of aluminum. The objects of research were samples of the coal part of the waste lining of dismantled S-8BM (E) type electrolytic cells of «RUSAL Krasnoyarsk» JSC (Krasnoyarsk) of RUSAL company. According to the X-ray experiment diffraction analysis (using a Bruker D8 ADVANCE diffractometer) of the phase composition of the samples, it was found that the main fluorine-containing compounds are cryolite, chiolite, sodium and calcium fluorides. The total fluorine content in the studied samples averaged 13.1 %. We conducted studies on the leaching of fluorine from WLEC with a solution of caustic alkali (NaOH concentration – 17.5 g/dm 3 ). The process was carried out in a mechanically agitated reactor using a BIOSAN MM-1000 top drive laboratory stirrer with a two-blade nozzle. By the method of mathematical planning of a three-factor experiment, the mutual influence of three leaching conditions on the optimization parameter was established – the extraction of fluorine in solution (in percent). The maximum recovery of fluorine from WLEC to the leach solution averaged 86.4 % and was achieved with the following indicators:processtemperature–95 ° C, the ratio ofliquidtosolidphase–9:1,duration– 210 min.
-
Date submitted2018-11-05
-
Date accepted2019-01-01
-
Date published2019-04-23
Features of elementary burst formation during cutting coals and isotropic materials with reference cutting tool of mining machines
- Authors:
- V. V. Gabov
- D. A. Zadkov
- Khac Linh Nguyen
The paper considers the cutting of brittle coals and rocks by a single cutter of a mining machine, in contrast to the generally accepted integral approach, different from the standpoint of the formation of successive elementary bursts that make up the cut. The process of the formation of an elementary bust in time is viewed as successive phases. Due to the complexity and multi-factor nature of the process, preference is given to experimental bench studies using reference cutters, isotropic materials, and real rock blocks. The bursting parameters values greatly influence the time of static forces action, the peculiarities of the formation of stress fields in the undercutter zone of the rock mass and the conditions for the emergence and development of main cracks in the near-cut zones during the cutting process. The accepted phase-energy method of analyzing the process, which most closely matches the structure of the studied process, revealed a more significant, than previously expected, effect on the cutting process, variability of cutting speed and potential energy reserve in the cutter drive. The paper discusses the possibility of purposeful formation of the parameters of elementary bursts. It describes new ways to improve the efficiency of cutting coal and rocks, in particular, reducing the maximum loads and specific energy consumption. It also considers the possibility of reducing the grinding of the rock mass and dust formation.
-
Date submitted2014-10-09
-
Date accepted2014-12-26
-
Date published2015-08-25
Improving the precision of manufacturing power hydraulic cylinders of powered roof supports based on a vibration-damping tooling system
- Authors:
- V. V. Maksarov
- Yu. Olt
The article deals with a new system of a vibration-damping tool, the effect of which is achieved by a combination of the multi-layer principle and the use of anisotropic properties of sheet metal. Operation of such tool systems in turning operations can reduce high-frequency vibra-tions arising in the process of cutting due to the ordered disorientation of anisotropic plate texture of a multilayer modular tool holder that allows you to efficiently dissipate oscillatory wave energy at the boundary of transition between the plates of the tool holder. This method allows increasing the resistance of the tool cutting edge significantly and expanding the technological capabilities for the effective selection of cutting modes to ensure compliance with requirements for dimensional and geometric accuracy, quality of processed surfaces of powered roof supports, hydraulic units, mining machinery and equipment.
-
Date submitted2009-08-08
-
Date accepted2009-10-26
-
Date published2010-02-01
Relationship between wear resistance of cutting bit body of mining tool and distribution of hardness along the cutting bit
- Authors:
- M. P. Talerov
In present article the courses of low wear resistance of rotary cutting bit body and also the courses of one-sided wear are described. The results of hardness of the cutting bit body from various manufacturers are represented here. In summary a conclusion was made that the utilization of thermal treatment after pressing removes specific structure that can be the course of one-sided wear genesis.