-
Date submitted2022-11-04
-
Date accepted2023-03-03
-
Date published2023-04-25
Efficiency of acid sulphate soils reclamation in coal mining areas
During the development of coal deposits, acid mine waters flowing to the surface cause the formation of acid sulphate soils. We study the effectiveness of soil reclamation by agrochemical and geochemical methods at the site of acid mine water discharge in the Kizel Coal Basin, carried out in 2005 using alkaline waste from soda production and activated sludge. A technosol with a stable phytocenosis was detected on the reclaimed site, and soddy-podzolic soil buried under the technogenic soil layer with no vegetation on the non-reclaimed site. The buried soddy-podzolic soil retains a strong acid рН concentration Н 2 О = 3. A high content of organic matter (8-1.5 %) is caused by carbonaceous particles; the presence of sulphide minerals reaches a depth of 40 cm. Technosol has a slightly acid pH reaction H 2 O = 5.5, the content of organic matter due to the use of activated sludge is 19-65 %, the presence of sulphide minerals reaches a depth of 20-40 cm. The total iron content in the upper layers of the technosol did not change (190-200 g/kg), the excess over the background reaches 15 times. There is no contamination with heavy metals and trace elements, single elevated concentrations of Li, Se, B and V are found.
-
Date submitted2021-02-12
-
Date accepted2022-07-26
-
Date published2022-11-10
Manifestation of incompatibility of marine residual fuels: a method for determining compatibility, studying composition of fuels and sediment
- Authors:
- Radel R. Sultanbekov
- Andrey M. Schipachev
The results of studying the problem of active sediment formation when mixing residual fuels, caused by manifestation of incompatibility, are presented. A laboratory method has been developed for determining the compatibility and stability of fuels allowing identification of a quantitative characteristic of sediment formation activity. Laboratory studies were performed, and incompatible fuel components were identified. Tests were made to determine the quality indicators of samples and group individual composition of fuels. Results on the content of total and inorganic carbon in the obtained sediments were determined using Shimadzu TOC-V SSM 5000A. Chemical composition was determined and calculated on LECO CHN-628 analyser. Group composition of hydrocarbon fuels contained in the sediment was studied by gas chromato-mass spectrometry on GCMS-QP2010 Ultra Shimadzu. To obtain additional information on the structural group composition of fuel sediment, IR spectrometry was performed on IR-Fourier spectrometer IRAffinity-1. X-ray diffraction analysis of sediment samples was made using X-ray diffractometer XRD-7000 Shimadzu; interplanar distances d002 and d100 as well as Lс and Lа crystallite sizes served as the evaluation criteria. Microstructural analysis of total sediment was performed by scanning electron microscopy. The results of the research confirmed that the content of normal alkanes in the fuel mixture mainly affects sediment formation. Recommendations were drawn on preserving the quality of fuels and reducing sediment formation during storage and transportation.
-
Date submitted2020-06-02
-
Date accepted2021-05-21
-
Date published2021-09-20
Analysis of technological schemes for creating a geodetic control at the industrial site
The article highlights the issues of creating with the necessary accuracy a planned control on the industrial site of the engineering structures under construction using satellite technologies and total stations. Depending on the design features of the engineering structures under construction, as well as the technological scheme for the installation of building constructions and industrial equipment, various schemes for creating such control are considered, based on the application of the inverse linear-angular notch. Errors in the source data are one of the main errors that affect the accuracy of geodetic constructions, including the solution of the inverse linear-angular notch. When creating a geodetic network in several stages, the errors of the initial data of the first stage affect the values of the root-mean-square errors (RMS) of determining the position of the second stage points, the errors of which affect the value of the RMS of the position of the third stage points, etc. The reason for their occurrence is the errors of geodetic measurements that occur at each stage of control creating, as well as the stability violation of the points during the production of excavation, construction and installation works. When determining the coordinates of a separate project point at the stage of its removal in-situ by a total station, the entire network is not equalized in the vast majority of cases, and the coordinates of the starting points to which the total station is oriented are considered error-free. As a result, the RMS determination of the points coordinates of the control network or the removal of the design points of the elements of building structures and equipment will also be considered satisfying the requirements, i.e. the measurement accuracy will be artificially overestimated and will not correspond to the actual one obtained. This is due to the fact that the accumulation of errors in the initial data is not taken into account when the number of steps (stages) of control creating increases. The purpose of this work is to analyze the influence of measurement errors and initial data when creating a geodetic control on an industrial site by several stages of its construction based on inverse linear-angular notches and a priori estimation of the accuracy of the determined points position.
-
Date submitted2020-05-21
-
Date accepted2020-10-05
-
Date published2020-11-24
Method of calculating pneumatic compensators for plunger pumps with submersible drive
- Authors:
- Eduard O. Timashev
One of the most promising ways to improve the efficiency of mechanized oil production is a plunger pump with a submersible drive, which allows obtaining harmonic reciprocating movement of the plunger. In the pumping process of well products by plunger pumps, oscillations in the velocity and pressure of the liquid in the lifting pipes occur, which lead to an increase in cyclic variable loads on the plunger, a decrease in the drive life period and the efficiency of the pumping unit. To eliminate the pulsation characteristics of the plunger pump and increase the reliability indicators of the pumping unit (in particular, the overhaul period), pneumatic compensators can be used. A method for calculating the optimal technological parameters of a system of deep pneumatic compensators for plunger pumping units with a submersible drive, based on mathematical modeling of hydrodynamic processes in pipes, has been developed. Calculations of the forming flow velocity and pressure in the lifting pipes of submersible plunger units equipped with pneumatic compensators (PC) have been carried out. Influence of the PC technological parameters on the efficiency of smoothing the oscillations of velocity and pressure in the pipes has been analyzed. Non-linear influence of the charging pressure and PC total volume on the efficiency of their work has been established. Optimal pressure of PC charging, corresponding to the minimum pressure in the tubing during the pumping cycle for the considered section of the tubing, is substantiated. Two ultimate options of PC system placement along the lifting pipes are considered. In the first option, PC are placed sequentially directly at the outlet of the plunger pump, in the second - evenly along the lift. It is shown that the first option provides the minimum amplitude of pressure oscillations at the lower end of the tubing and, accordingly, variable loads on the pump plunger. Nature of the pressure and flow velocity oscillations in the tubing at the wellhead for both options of PC placement has similar values .
-
Date submitted2019-11-20
-
Date accepted2020-01-20
-
Date published2020-10-08
Effect of shear stress on the wall of technological pipelines at a gas condensate field on the intensity of carbon dioxide corrosion
The object of the study is a section of the gas and gas condensate collection system, consisting of an angle throttle installed on a xmas tree and a well piping located after the angle throttle. The aim of the study is to assess the impact of the flow velocity and wall shear stress (WSS) on the carbon dioxide corrosion rate in the area of interest and to come up with substantiated recommendations for the rational operation of the angle throttle in order to reduce the corrosion intensity. In the course of solving this problem, a technique was developed and subsequently applied to assess the influence of various factors on the rate of carbon dioxide corrosion. The technique is based on a sequence of different modeling methods: modeling the phase states of the extracted product, three-dimensional (solid) modeling of the investigated section, hydrodynamic flow modeling of the extracted product using the finite volume method, etc. The developed technique has broad possibilities for visualization of the obtained results, which allow identifying the sections most susceptible to the effects of carbon dioxide corrosion. The article shows that the average flow velocity and its local values are not the factors by which it is possible to predict the occurrence of carbon dioxide corrosion in the pipeline section after the angle throttle. The paper proves that WSS has prevailing effect on the corrosion intensity in the section after the angle choke. The zones of corrosion localization predicted according to the technique are compared with the real picture of corrosion propagation on the inner surface of the pipe, as a result of which recommendations for the rational operation of the angle throttle are formed.
-
Date submitted2018-12-25
-
Date accepted2019-03-02
-
Date published2019-06-25
Non-linear electrical load location identification
- Authors:
- S. Pirog
- Ya. E. Shklyarskiy
- A. N. Skamyin
The article discusses the issues of identifying the location of non-linear loads in electrical networks which makes the main contribution to the distortion of the non-sinusoidal voltage and current in the distribution network of an industrial enterprise, including mining enterprises. The existing methods for determining the location of the source of higher harmonic components in voltage and current are considered, their advantages and disadvantages are revealed. The main disadvantages of the methods used include the low accuracy and incorrectness of their use in existing enterprises. When developing a new method, the authors were faced with the task of simplicity of its use in the conditions of industrial operation of electrical equipment and the absolute correctness of the results obtained. The proposed method of identifying the source of higher harmonics is based on the variation of the parameters of the power system, in particular, the change in resistance of power transformers taking into account their transformation ratio. It is shown that by varying the transformation ratio during regulation under load, the total coefficient of the harmonic components of the voltage changes. Based on the constructed dependencies, the variation of the derivative of this function with different variations of the parameters of sources of higher harmonics is analyzed and a method is developed that allows determining the share contribution of consumers to the total harmonic component of the voltage.
-
Date submitted2018-11-03
-
Date accepted2019-01-16
-
Date published2019-04-23
Interpretation of the tracer investigation results considering convective mass transfer
- Authors:
- V. A. Korotenko
- S. I. Grachev
- A. B. Kryakvin
The paper discusses the results of interpreting well tracer studies. It is shown that from the law of mass conservation it follows that when filtering a volume of an indicator, part of the injected tracer flows into the matrix. With the flow of fluid containing the indicator from the low-filtration resistance channel (LFR) into the surrounding matrix, the linear dimensions of the flow area depend on the permeability and porosity properties of the high-permeability channel and the matrix. While another part of the tracer moves toward the production well, its mass is lost due to diffusion processes. From the solution of the diffusion equation, it follows that the initial concentration of the tracer decreases in the course of filtration along the LFR channel. To interpret the results of the tracer studies, different cases of the LFR channels' location in the volume of the productive formation are considered. The varied parameter w allows characterizing the presence of several peaks in the concentration of the indicator and calculation the filtration parameters of the LFR channels. Depending on the known technological indices, several methods for determining pore volumes in the LFR channels have been proposed. To reduce the water cut in producing wells and to apply the technology of changing or aligning the injectivity profiles, calculations of the pore channels' radii in the mass of highly permeable seams are presented. It is shown that the volume of the chemical reagent pumped into the injection well to isolate the LFR channel is affected by the linear dimensions of the drainage area for the aqueous solution of indicator. Examples of the calculation for the permeability and porosity parameters of the LFR, the volume of pore channels necessary to isolate water inflow, and the radii of pore filtration channels, which influence the selection of the size of chemical reagent molecules, are given.
-
Date submitted2018-05-20
-
Date accepted2018-07-07
-
Date published2018-10-24
Justification of representative data volume of porosity and permeability properties for obtaining statistically reliable petrophysical connections
- Authors:
- A. A. Abrosimov
- E. V. Shelyago
- I. V. Yazynina
The article discusses the issues of justifying the data volume for a petrophysical description of an object based on the results of traditional laboratory measurements, as well as X-ray tomography data processing. A new approach to the calculation of porosity and permeability properties of reservoirs with the data of the X-ray tomography method by forming an array of virtual cubes is considered. The issues of required number of allocated cubes for fluid dynamics modeling are discussed. The criteria for the number of laboratory measurements and virtual cubes derived from a digital model for obtaining statistically reliable petrophysical connections are shown. Paper concludes that it is necessary to correctly compare the calculated and laboratory petrophysical connections.
-
Date submitted2016-09-06
-
Date accepted2016-11-13
-
Date published2017-02-22
Justified selection of a seam degassing technology to ensure safety of intensive coal mining
- Authors:
- S. V. Slastunov
- E. P. Yutyaev
The paper contains main aspects of methodological approach to objective analytic assessment of maximum permissible output of the mine faces from the viewpoint of gas factor. Analytic forecast is centered around the assessment of methane inflow into the face area from all possible sources, based on fundamental physical laws, modern tools of mathematical modeling and in-situ tests of main properties and state parameters of the gas-bearing coal formation. Objective and reliable estimation of permissible outputs is a starting point for justified selection of a seam degassing technology, that has to be based on time factor and predicted value of gas recovery from a coal seam to a degassing well. Recommendations have been formulated on the selection of degassing technology for the coal seam «Boldyrevsky» of the Kirov mine, based on the use of cutting-edge technological schemes (hydraulic fracture, carried out from development workings, etc.), successfully implemented on the mentioned site.
-
Date submitted2013-07-14
-
Date accepted2013-09-07
-
Date published2014-03-17
Open cast geological conditions analysis and the mining units formation in ore losses and dilution determining
- Authors:
- S. I. Fomin
- P. B. Kava
- M. A. Marinin
The opencast geological conditions analysis and the mining units formation in ore losses and dilution determining is given in dynamic type. The optimum height of immixed rocks triangle on minimum economic damage from losses and dilution criterion is determined. Minimum damage of an enterprise from losses and dilution of one ton of ore that provides minimum producing cost of ore mining is accepted as a criterion of optimum correlation of technological standards of rate of contact areas and standards of losses and dilution of ore.
-
Date submitted2013-07-23
-
Date accepted2013-09-11
-
Date published2014-03-17
Use of coefficient of output at pit delimitation
- Authors:
- G. A. Kholodnyakov
- N. S. Vainonen
In work it is settled an invoice the final depth of a pit of the conditional complex occurrence presented by three minerals. It is shown that when developing complex occurrence it is more expedient to use coefficient of output, instead of overburden ratio.
-
Date submitted2013-07-26
-
Date accepted2013-09-18
-
Date published2014-03-17
Mining units quantity determination to achieve the established open cast output and averaging ore requirements
- Authors:
- S. I. Fomin
- V. A. Shevelev
- M. A. Marinin
The balancing stripping ratio and ore production methods include simulation in order to reduce the prestripping waste and maintain a suitable space between each bench. The reliability analysis method of mining technological system in mine design is discussed in this paper. The probabilistic approach used here takes into consideration the uncertainty associated with estimation of most economic, mining and geological variables. This paper concerns the rational distribution of reserves which can be mined and waste advancing down the open cast site at steep pitch deposit.
-
Date submitted2010-07-14
-
Date accepted2010-09-07
-
Date published2011-03-21
Substantiation of pumped volumes of flow angularity compositions in injection wells
- Authors:
- A. R. Mavliev
- M. K. Rogachev
- D. V. Mardashov
The method of calculation pumped volumes of flow angularity compositions in injection wells, which based on combination of the seepage theory, laboratory investigation and field experience is developed.
-
Date submitted2009-10-02
-
Date accepted2009-12-23
-
Date published2010-09-22
The problems of efficient use of the tumenian reservoirs at final stage of low-pressure gas production and prospects in their solutions
- Authors:
- O. E. Bugriy
The reserves depletion estimation is presented for main (base) fields in the north part of the Tumenian area. The significance of long time production of base fields is shown. The main problems of efficient use are shown for reservoirs at final stage of low-pressure gas field. The methodology associated with solving the problem is formulated for low profitability in low-pressure gas output. The recommendations for State support of subsurface users are prepared for efficient low-pressure gas production and efficient use of reserves at all.
-
Date submitted2009-10-10
-
Date accepted2009-12-02
-
Date published2010-09-22
Deformational precursors of technogenic earthquakes in mining the hydrocarbon deposits
During monitoring since 2005 to 2008 at the Astrakhan gas-field it has been recorded three technogenic earthquakes. Results of geodetic levelling for the given period allow to approve that seismic event is preceded by raisings of a surface and its subsequent subsidence as a its result of unloading. That allows to use geodetic levelling for the forecast of technogenic seismic phenomena for oil and gas fields.
-
Date submitted2009-10-21
-
Date accepted2009-12-26
-
Date published2010-09-22
Modeling of geomechanical processes in mining the steeply pitching ore bodies of rockburst-hazardous deposits
The article contains the results of numerical modeling of stress-strain state in constructive elements of mining systems, applied at hazardous and prone to rook bursts deposits of the Far-East. Consideration is given to some stated regularities of forming of teсhnogenic stress field and geomechanical processes proceeding in rock mass of minable deposits which allow to substantiate a сomplex of measures for prevention of dynamic rock pressure manifestations.
-
Date submitted2009-10-26
-
Date accepted2009-12-27
-
Date published2010-09-22
Support of geodynamic safety in mining of the Khibini deposits
The paper deals with the problems of geodynamics in mining of the Khibini deposits. Description is given to the complex of organizational-technical arrangements for provision of geodynamic safety at the Apatit Co and to principal trends of its development.
-
Date submitted2009-07-12
-
Date accepted2009-09-08
-
Date published2010-04-22
Account and movement of reserves in the information system of Silvinit co.
- Authors:
- A. V. Kataev
- S. N. Kutovoi
- E. M. Efimov
- M. V. Gilev
At ore mines of the Silvinit Co. for accounting and movement of reserves are developed and used special tools, using GIS within the information system. Their use allows to automate accounting and monitoring of status and movement of stocks, including the formation of the reporting tables.
-
Date submitted2009-07-29
-
Date accepted2009-09-29
-
Date published2010-04-22
State examination of mineral reserves in the system of wise utilization of the earth’s interior
- Authors:
- Yu. A. Podturkin
The major problem of bodies of the government in sphere of regulation of attitudes protection of reserves creation of conditions for rational use of resources. The basic role in its decision is played with examination protection of reserves. Maintenance of effective carrying out of examination demands its constant perfection with reference to market conditions with use of the international criteria regarding both calculation and an estimation of stocks, and drawing up design and the engineering specifications on development of mineral deposits.
-
Date submitted2009-07-09
-
Date accepted2009-09-02
-
Date published2010-04-22
Examination of utilization of the earth’s interior is a wise use of mineral reserves
- Authors:
- Yu. A. Podturkin
The Russian economy is appreciably defined by the richest minerals -raw potential and effective strategy of its use. The major problems of bodies of the Government in sphere of regulation of attitudes protection of reserves is the objective economic estimation of stocks of minerals, their authentic state account, involving in development of a maximum quantity of minerals at existing economy and technologies, decrease in losses of minerals in extraction and processing, complex processing of raw material, prevention of cases of injurious working off of stocks.
-
Date submitted2008-11-13
-
Date accepted2009-01-01
-
Date published2009-12-11
The quality of commodity output – the factor of competitiveness iron-ore branch
- Authors:
- R. V. Korchenkov
The problems of quality improving of commodity output are the most urgent and up-to date questions in the period of intromission of Russian on the world market. The country possesses of significant mineral raw ferrous materials, which are poor quality. In conjunction with it mining-and-processing integrated works must develop and improve the process of production in order to provide the quality of the products conforming to world requirements. The main task of iron-ore branch in Russia is to maintain the competitive ability on the foreign market.
-
Date submitted2008-10-07
-
Date accepted2008-12-05
-
Date published2009-12-11
The application of areal technology and 3d data interpretation tem sounding when constructing the volume geoelectrical model of compound medium
Analysis of possibilities of different electrical technologies is carried out. Problems of applications of one-dimension and multidimensional inversions in the process of interpretation are discussed. Example of practical application of two- and three-dimension interpretation of electrical data in the process of ore prospecting in complicated geological media is presented. The example illustrates possibilities of electrical method as original research method, which enables to develop three-dimensional models of the medium under investigation.