-
Date submitted2022-09-30
-
Date accepted2024-11-07
-
Date published2025-02-25
Carbon dioxide corrosion inhibitors: current state of research and development
Among the methods of corrosion control in the oil and gas production industry the leading place belongs to inhibitor protection, since there is no need for technological and technical changes in the existing equipment. The combination of high variability of inhibitor composition with changing conditions of its application and low capital investments makes it an indispensable reagent at oil and gas fields. The main classes of compounds used as active bases of carbonic acid corrosion inhibitors for the protection of oil and gas equipment are described. Classical organic active bases containing heteroatoms (oxygen, sulfur, nitrogen) are examined. Special attention was paid to alkylimidazolines and other nitrogen-containing compounds as the most frequently used as active bases of carbonic acid corrosion inhibitors in Russia and abroad. A wide range of possibilities to achieve the desired properties of corrosion inhibitors by varying the substitutes has been demonstrated. Nowadays, in addition to the traditional requirements for corrosion inhibitors, their safety for the environment is equally important. The information on prospective research and development aimed at improving the environmental characteristics of the reagents used is given. Plant extracts, synthetic and biological polymers involved in traditional corrosion inhibitors or used as new independent compounds are considered. It is shown that the effectiveness of corrosion inhibitors significantly depends on the pH of the medium, temperature, partial pressure of СО2, flow rate, and other factors.
-
Date submitted2021-02-09
-
Date accepted2023-09-20
-
Date published2024-02-29
Analysis of experience in the use of preformed particle polymer gels in the development of high-water-cut production facilities in low-temperature oil reservoirs
- Authors:
- Sergei V. Galkin
- Yuliya A. Rozhkova
Foreign practice of oil production in high-water-cut conditions suggests using the technology of injection of preformed particle gel (PPG) suspension into injection wells. After swelling, the polymer particles become elastic and are able to penetrate through highly permeable watered intervals into the remote reservoir zone, forming a polymer “plug”. Thus far, the domestic experience of application of this technology boiled down to testing foreign compounds. We have looked into the possibilities of PPG technology application in geological and technological conditions of high-water-cut fields of Perm Krai. The paper proposes PPG reagents effective in low-temperature reservoirs (20-35 °С) and at relatively high salinity of formation water (more than 200 g/l). The world experience of PPG technology application was analyzed to identify the principal scheme of reagent injection, to establish variants of sequence of injection of PPG particles of different sizes, as well as the possibility of regulating the morphological characteristics of polymer gel particles during synthesis depending on the porosity and permeability of the reservoir. A prerequisite for the technology is the ability to remove PPG particles after treatment from the bottom-hole zone of the formation; for this purpose, tests were carried out on a breaker compound based on sodium persulfate with synergizing additives. PPG technology is effective in reservoirs with high permeability heterogeneity. Two types of high-water-cut production facilities potentially promising for PPG realization have been identified for oil fields of Perm Krai. The first type includes carbonate Tournaisian-Famennian reservoirs with pronounced macrofracturing, in which the PPGs are used for colmatation of flushed large fractures. The second type is terrigenous Visean deposits with increased oil viscosity from 5 to 100 mPa∙s and high permeability of reservoirs (> 0.5 μm2). For both types of reservoirs, areas have been selected that are promising for the implementation of PPG technology.
-
Date submitted2023-07-07
-
Date accepted2023-09-20
-
Date published2024-02-29
Isotherm and kinetic adsorption of rice husk particles as a model adsorbent for solving issues in the sustainable gold mining environment from mercury leaching
One of the techniques used in extracting gold in small-scale gold mining is mercury amalgamation. However, the use of mercury presents significant health and environmental hazards, as well as suboptimal efficiency in gold extraction. This study explores the possibility of the use of rice husk as a prototype adsorbent for mercury removal from its leaching in mining environments. To support the analysis, the rice husk adsorbent was characterized by Fourier-transform infrared spectroscopy, scanning electron microscopy, electron dispersive X-ray spectroscopy, atomic absorption spectrophotometers and Brunauer − Emmett − Teller analysis. To investigate the removal of Hg from aqueous solutions, batch adsorption experiments were conducted, and the efficiency was optimized under various parameters such as contact time, rice husk dosage, and initial concentration of mercury. Kinetic and isotherm investigations were also carried out to gain a better understanding of the adsorption properties. The kinetic adsorption was analyzed using the pseudo-first-order and pseudo-second-order. Furthermore, the isotherm adsorption was analyzed using ten adsorption isotherm models (i.e., Langmuir, Freundlich, Temkin, Dubinin – Radushkevich, Flory – Huggins, Fowler – Guggenheim, Hill – de Boer, Jovanovic, Harkin – Jura, and Halsey). The amount of mercury absorption increased with increasing contact time, adsorbent mass, and initial concentration of mercury. The pseudo-second-order kinetic model is the best model that can be applied to describe the adsorption process. Analysis of the adsorption results obtained shows that the adsorption pattern is explained through the formation of a monolayer without any lateral interaction between the adsorbate and adsorbent. In addition, the formation of multilayers due to inhomogeneous pore distribution also occurs which causes a pore filling mechanism. We found that the isotherm phenomena are near the Jovanovic models with the maximum adsorption capacity) of rice husk found to be 107.299 mg/g. As a result, rice husk could be a promising option for wastewater treatment due to its fast and efficient removal capacity, as well as its affordability and eco-friendliness. The predicted thermodynamic studies using the Flory – Huggins isotherm model show that the adsorption process is endothermic, spontaneous, and physisorption. The impact shows that the utilization of rice husk can be used and fit for the current issues in the sustainable development goals (SDGs).
-
Date submitted2023-04-29
-
Date accepted2023-10-11
-
Date published2023-10-27
Pink-violet diamonds from the Lomonosov mine: morphology, spectroscopy, nature of colour
The article presents the results of the first comprehensive study of mineralogical and spectroscopic (IR, PL, EPR) characteristics of diamonds from the Lomonosov mine (Arkhangelskaya pipe) with a unique pink, pink-violet colour. It is shown that all crystals belong to the IaA type, with a total nitrogen content in the range of 500-1500 ppm, with a low degree of aggregation. The colour is heterogeneous, concentrated in narrow twin layers. It is presumably caused by the previously described M2 centres. The colour shade is affected by the content of P1 paramagnetic centres (C-defect). A positive correlation is observed between the colour saturation and the intensity of W7 paramagnetic centres. A convergent model of the formation of pink diamonds is assumed, according to which the determining factors are the ratio and concentration of structural impurities in the diamond, its thermal history, and conditions of plastic deformation, and not the origin of the diamond and the petrochemical properties of its host rocks.
-
Date submitted2022-03-01
-
Date accepted2022-05-25
-
Date published2022-12-29
Study on the rheological properties of barite-free drilling mud with high density
Improved drilling and reservoir penetration efficiency is directly related to the quality of the drilling mud used. The right choice of mud type and its components will preserve formation productivity, stability of the well walls and reduce the probability of other complications. Oil and gas operators use barite, less often siderite or hematite weighting agent as a weighting component in the composition of drilling muds for the conditions of increased pressure. But the use of these additives for the penetration of the productive formation leads to the reduction of filtration characteristics of the reservoir, as it is almost impossible to remove them from the pore channels. Therefore, barite-free drilling mud of increased density based on formic acid salts with the addition of carbonate weighting agent as an acid-soluble bridging agent is proposed. The results of experimental investigations on rheological parameters of barite-free solutions are given and the obtained data are analyzed. Based on the comparison of results it is recommended to use high-density drilling mud on the basis of formic acid salts (sodium and potassium formate) and with the addition of partially hydrolyzed polyacrylamide with molecular mass of 27 million.
-
Date submitted2022-05-13
-
Date accepted2022-09-24
-
Date published2022-11-03
Rapid detection of coal ash based on machine learning and X-ray fluorescence
Real-time testing of coal ash plays a vital role in the chemical, power generation, metallurgical, and coal separation sectors. The rapid online testing of coal ash using radiation measurement as the mainstream technology has problems such as strict coal sample requirements, poor radiation safety, low accuracy, and complicated equipment replacement. In this study, an intelligent detection technique based on feed-forward neural networks and improved particle swarm optimization (IPSO-FNN) is proposed to predict coal quality ash content in a fast, accurate, safe，and convenient manner. The data set was obtained by testing the elemental content of 198 coal samples with X-ray fluorescence (XRF). The types of input elements for machine learning (Si, Al, Fe, K, Ca, Mg, Ti, Zn, Na, P) were determined by combining the X-ray photoelectron spectroscopy (XPS) data with the change in the physical phase of each element in the coal samples during combustion. The mean squared error and coefficient of determination were chosen as the performance measures for the model. The results show that the IPSO algorithm is useful in adjusting the optimal number of nodes in the hidden layer. The IPSO-FNN model has strong prediction ability and good accuracy in coal ash prediction. The effect of the input element content of the IPSO-FNN model on the ash content was investigated, and it was found that the potassium content was the most significant factor affecting the ash content. This study is essential for real-time online, accurate, and fast prediction of coal ash.
-
Date submitted2022-04-13
-
Date accepted2022-06-15
-
Date published2022-07-26
Thermal history of diamond from Arkhangelskaya and Karpinsky-I kimberlite pipes
This work studies and compares the main morphological, structural, and mineralogical features of 350 diamond crystals from the Karpinsky-I and 300 crystals of the Arkhangelskaya kimberlite pipes. The share of crystals of octahedral habit together with individual crystals of transitional forms with sheaf-like and splintery striation is higher in the Arkhangelskaya pipe and makes 15 %. The share of cuboids and tetrahexahedroids is higher in the Karpinsky-I pipe and stands at 14 %. The share of dodecahedroids in the Arkhangelskaya and Karpinsky-I pipes are 60 % and 50 %, respectively. The indicator role of the nitrogen-vacancy N3 center active in absorption and luminescence is shown. Crystals with the N3 absorption system have predominantly octahedral habit or dissolution forms derived from the octahedra. Their thermal history is the most complex. Absorption bands of the lowest-temperature hydrogen-containing defects (3050, 3144, 3154, 3188, 3310 cm −1 , 1388, 1407, 1432, 1456, 1465, 1503, 1551, 1563 cm −1 ), are typical for crystals without N3 system, where in the absorption spectra nitrogen is in the form of low-temperature A and C defects. The above mentioned bands are registered in the spectra of 16 % and 42 % of crystals from the Arkhangelskaya and Karpinsky-I pipes, respectively. The diamond of the studied deposits is unique in the minimum temperature (duration) of natural annealing. Based on a set of features, three populations of crystals were distinguished, differing in growth conditions, post-growth, and thermal histories. The established regularities prove the multi-stage formation of diamond deposits in the north of the East European Platform and significant differences from the diamonds of the Western Cisurals. The results suggest the possibility of the existence of primary deposits dominated by diamonds from one of the identified populations.
-
Date submitted2021-09-17
-
Date accepted2022-04-07
-
Date published2022-12-29
Technique for calculating technological parameters of non-Newtonian liquids injection into oil well during workover
Technique for automated calculation of technological parameters for non-Newtonian liquids injection into a well during workover is presented. At the first stage the algorithm processes initial flow or viscosity curve in order to determine rheological parameters and coefficients included in equations of rheological models of non-Newtonian fluids. At the second stage, based on data from the previous stage, the program calculates well design and pump operation modes, permissible values of liquid flow rate and viscosity, to prevent possible hydraulic fracturing. Based on the results of calculations and dependencies, a decision is made on the necessity of changing the technological parameters of non-Newtonian liquid injection and/or its composition (components content, chemical base) in order to prevent the violation of the technological operation, such as unintentional formation of fractures due to hydraulic fracturing. Fracturing can lead to catastrophic absorptions and, consequently, to increased consumption of technological liquids pumped into the well during workover. Furthermore, there is an increased risk of uncontrolled gas breakthrough through highly conductive channels.
-
Date submitted2021-02-20
-
Date accepted2021-05-21
-
Date published2021-09-20
Analysis of the screw press mouthpiece parameters for 3D extrusion of peat pieces of tubular type
The results of theoretical and experimental studies on the creation of a screw press composite mouthpiece screw press for 3D-forming of peat pieces of a tubular type in the field for intensifying the process of field drying of material in a complex mechanized pit are presented. The main purpose of the study was to substantiate the geometric and design parameters of the screw press composite mouthpiece of the spread machine for the production of peat-agglomerated products of the tubular type. The parameters of the mouthpiece are selected based on the geometric characteristics of the peat pieces. An increase in moisture loss during drying of peat-agglomerated products is provided by forming a peat piece in the form of a thick-walled pipe made of a peat raw materials composed of low and high decomposition degrees in a ratio of 1:3. Additive production of polymer-fiber peat composites by extrusion allows to produce products with improved mechanical properties in comparison with non-reinforced raw materials. The vertical arrangement of the peat tubular piece on the drying field allows to increase the loading of the field area by 10 %, increase the convective heat supply to the piece and reduce the contact coefficient of the piece with the field by three times in comparison with the peat spreading of the pieces in the form of a horizontal tape. Based on the analysis of the shape and size of the agglomerated products, the design of a screw press composite mouthpiece consisting of two conditional molding zones of various configurations has been developed. The article presents a parametric analysis of the volumetric productivity of a screw press with a composite mouthpiece of a tubular type, the energy intensity of mechanical processing is determined, the degree of mechanical processing of peat raw materials is estimated with the optimization of the screw parameters for the production of agglomerated products of a tubular type.
-
Date submitted2020-06-16
-
Date accepted2021-03-29
-
Date published2021-09-20
Empirical regularities investigation of rock mass discharge by explosion on the free surface of a pit bench
- Authors:
- Igor A. Alenichev
- Ruslan A. Rakhmanov
Minimizing the discharge of blasted rock mass into the developed space of the pit is a very relevant area for study, as it allows to increase the processability of work and reduce the cost of mining. The article presents the results of experimental industrial explosions, during which the study of this issue was conducted. The main purpose of the work was to establish the key factors affecting the volume of rock mass discharge to the pit haulage berm. During the analysis of the world experience of research on this topic, the key factors affecting the formation of collapse and discharge – natural and technological – are identified. The method of conducting experiments and collecting data for analyzing the influence of technological parameters of location, charging and initiation of wells on the volume of rock mass discharge is described. It is established that the main discharge to the pit haulage berm is formed by the volume of rock mass limited by the prism of the slope angle. With a sufficient rock mass displacement from the edge of the bench crest towards the center of the block, only the wells of the 1st and 2nd rows participate in the discharge formation. Empirical dependences of the total volume of rock mass discharge on the length of the block along the bench crest, the specific consumption of explosives, the size of a rock piece P 50 and the rate of rock breaking are obtained. The obtained results can be used to design the parameters of the drilling and blasting operations (DBO), as well as to predict and evaluate the possible consequences of a mass explosion in similar mining and geological conditions.
-
Date submitted2020-12-11
-
Date accepted2021-03-30
-
Date published2021-06-24
Development of new compositions for dust control in the mining and mineral transportation industry
Dust control in summer and winter periods is a topical problem associated with conducting open pit mining operations; however, at negative temperatures the additional requirements are imposed on dust suppressants. Preventive compositions are proposed, in which light and heavy gas oils, obtained from catalytic cracking and delayed coking, are used as base components. Involvement of heavy fractions allows to increase the flash point, thereby reducing the flammability of dust suppressant, improve its adhesion properties by increasing the content of polyaromatic hydrocarbons and reduce the cost of the final product. In order to improve low-temperature and adsorption properties of developed dust suppressants, heavy oil residues (cracking residue and tar) are included in their composition in various concentrations: 2-10 wt.%. Alternative compositions of dust suppressants, obtained by water emulsification of vinylated alkyd oligomer, are developed; the ability of this dispersion to form strong films on dusty surfaces is examined. The efficiency of using aqueous solution of vinylated alkyd oligomer as a summer dust suppressant is demonstrated. The results of this study include the development of new preventive compositions with improved low-temperature properties and confirmation of the theoretical part of the study by the results of performance tests on a laboratory facility.Alternative compositions of dust suppressors have been developed, which were obtained by emulsifying a vinyl alkyd oligomer (VAO) in water; the ability of this dispersion to form strong films on dusty surfaces has been studied. The efficiency of using an aqueous solution of vinyl alkyd oligomer in the summer period as a dust suppressant is shown. The results of this study are the development of new prophylactic formulations with improved low-temperature properties and confirmation of the theoretical part of the study by the results of tests of operational characteristics in a laboratory facility.
-
Date submitted2019-11-28
-
Date accepted2020-05-08
-
Date published2020-10-08
Development of the drilling mud composition for directional wellbore drilling considering rheological parameters of the fluid
Article presents investigations on the development of a drilling mud composition for directional wells in an oil field located in the Republic of Tatarstan (Russia). Various rheological models of fluid flow and their applicability for drilling muds are analyzed. Laboratory experiments to measure the main rheological parameters of a solution, such as plastic viscosity, dynamic shear stress, as well as indicators of non-linearity and consistency are presented. On the basis of laboratory investigations, it was concluded that high molecular weight polymer reagents (for example, xanthan gum) can give tangible pseudoplastic properties to the washing fluid, and their combination with a linear high molecular weight polymer (for example, polyacrylamide) reduces the value of dynamic shear stress. Thus, when selecting polymer reagents for treating drilling muds at directional drilling, it is necessary to take into account their structure, molecular weight and properties. Combination of different types of reagents in the composition of the drilling mud can lead to a synergistic effect and increase the efficiency of the drilling process as a whole.
-
Date submitted2019-08-08
-
Date accepted2019-09-16
-
Date published2020-02-25
Testing of preformed particles polymer gel technology on core filtration models to limit water inflows
In order to reduce watering of wells and equalize their injectivity profiles, the prospects of introducing PPG technology in Russian fields are considered, in which preformed particles polymer gel are pumped into the injection well. These particles, being a supersorbent based on polyacrylamide, absorb water, become elastic, which allows them to shrink and tear in narrow filtration channels. When the polymer is filtered along permeable layers saturated with water, polymer particles accumulate in waterlogged intervals and thus they form a polymer plug, which redistributes the filtration flows and increases the coverage of the formation by the process of oil displacement. More than 4000 downhole operations have been carried out in the fields of China and the USA using PPG technology by now. In domestic fields in Western Siberia, there is limited experience in applying a similar technology in high-temperature formations with low mineralization of formation water. Due to the absence of hydrolytic processes in polyacrylamide, well-known domestic compositions are not applicable due to the low absorption capacity in the conditions of low-temperature deposits with increased mineralization of formation water. The authors synthesized a polymer based on polyacrylamide by block polymerization, which allows to obtain a high absorption capacity, including for low-temperature formations with high mineralization of formation water, which is typical for Perm Territory fields. Filtration experiments were carried out on core models with the composition developed by the authors, this composition focused on low formation temperatures and high mineralization of formation water. As a result of the experiments, it was found that the swollen particles of the gel are able to pass into fractures with a diameter less than their own size at least 20 times. With a significant increase in the viscosity of the dispersion medium, the stability of the suspension increases. Particles of polymer gel have the necessary strength for injection in the field conditions. The fracture permeability during polymer injection decreases by several times and becomes comparable with the permeability of pore collectors.
-
Date submitted2018-08-30
-
Date accepted2018-10-26
-
Date published2019-02-22
Study of bearing units wear resistance of engines career dump trucks, working in fretting corrosion conditions
- Authors:
- Ju. Olt
- V. V. Maksarov
- V. A. Krasnyy
The occurrence of fretting corrosion on nominally fixed surfaces of high-loaded parts of mining machines and mechanisms is considered. Examples of wear and damage of critical parts, bearing assemblies of engines of dump trucks in fretting conditions are given. The mechanisms of fretting corrosion when using wear-resistant coatings are considered. It is noted that when choosing protective thin-layer coatings that provide an increase in the fretting-resistance of surfaces of tightly contacting parts, it is necessary to take into account both their wear resistance and the ability to resist shear. At the same time, the thickness of such coatings allows preserving, during operation, those provided during the assembly of the tension, without disturbing the maintainability of the nodes. The results of research of fretting wear of a number of coatings on a special installation are given. The mechanisms of wear of a number of thin-layer coatings based on friction-mechanical brazing, polymer fluorocarbon composition, solid lubricant coating using scanning electron microscopy were studied. Recommendations on the use of the studied thin-layer coatings for high-loaded parts of mining machines operating in fretting corrosion conditions have been developed. The aim of the work was to study the effect of a number of thin-layer coatings on the wear of highly loaded connections of the mechanisms of mining machines, in particular bearing assemblies of quarry dump trucks operating under fretting corrosion conditions.
-
Date submitted2017-11-20
-
Date accepted2018-01-09
-
Date published2018-04-24
Sulfidization of silver-polymetallic ores of «Goltsovoe» deposit for decreasing loss of silver in mill tailings
- Authors:
- L. V. Shumilova
- O. S. Kostikova
The results of laboratory studies of flotation concentration of silver-polymetallic ores of the Goltsovoe deposit at the Omsukchansk concentrator are presented. The results of sieve analysis of mill tailings of the experimental sample of MTP N 101 (N 7577-i) are described. They indicate that a large amount of silver (123 g/t) is lost in the size class – 0.040 mm (yield 50.25 %). According to the results of mineralogical analysis, it is established that the major losses of noble metal are associated with its fine impregnation in oxides, sulfides and silicate rocks. The main silver-bearing minerals are acanthite, polybasite and kustelite (class – 0.040 mm). Experimental studies were carried out in two stages. The purpose of the first stage is to determine the influence of grinding fineness in flotation feed (for a finished class content of 0.074 mm in the range of 60-95 %) for silver recovery at different amounts of butyl potassium xanthate (50, 150, 300 g/t). The purpose of the second stage is to evaluate the effectiveness of sulfidization at different consumption of sodium sulfide Na 2 S·9H 2 O (50, 150, 200, 450, 750 g/t – 1 % aqueous solution) under the conditions of the optimal reagent mode established in the first stage of the study. The results of experiments to determine the optimum grinding fineness and studies on the enrichment of silver-polymetallic ore with the use of sodium sulfide as a sulfidizer are presented. The efficiency of the sulfidization process is estimated. The following experimental dependencies of silver recovery are established: on the degree of grinding and consumption of butyl potassium xanthate; on variations of grinding fineness and the consumption of sodium sulphide (with a consumption of butyl xanthate 150 g/t); and on grinding fineness at optimum consumption of sodium sulfide 150 g/t and butyl potassium xanthate 300 g/t. A comparative evaluation of dependence of silver recovery index from the degree of grinding fineness before and after introduction of sodium sulphide (collecting agent consumption of 150 g/t) is given. T\
-
Date submitted2015-07-05
-
Date accepted2015-09-01
-
Date published2016-02-24
Substantiation of intrastratal water shutoff technology in low permeability reservoirs
- Authors:
- M. K. Rogachev
- A. O. Kondrashev
The article presents the results of the filtration tests of the developed polymeric waterproofing compound GPS-1, which is a mixture of a water-alkaline hydrolyzed acryl-containing polymer solution with a nonionic surfactant. The obtained results indicate significant improvements of main operational parameters – penetrating and water-insulating power of the developed polymeric composition GPS-1 in comparison with the original one: addition of the nonionic surfactant reduced the pressure gradient of injection twice. Also, considerable (5 times) increase of the residual resistance factor, that is explained by deeper and more uniform penetration of the solution into the porous medium and the corresponding raise of isolation efficiency of pore channels, is established. Experiments on the model of a heterogeneous oil-filled formation showed that after the injection of the polymeric solution water mobility decreases in a highly porous interlayer and increases in a low-permeability interlayer indicating a redistribution of filtration flows in the model of a heterogeneous bed. The decrease of water mobility in a high-permeability zone contributes to the leveling of the displacement front and, ultimately, the additional extraction of oil from the less permeable area. As a result of the complex of filtration tests conducted, the efficiency of the developed polymeric composition GPS-1 for the regulation of filtration flows in low-permeability heterogeneous reservoirs is proved.
-
Date submitted2014-12-24
-
Date accepted2015-02-11
-
Date published2015-12-25
Freiberg mining academy and Mining cadet corps: their place and role in Humboldt´s life and activities
- Authors:
- I. G. Rebeshchenkova
The article examines the stages and events of Humboldt s life, associated with the European institutions: Freiberg Mining Academy and the Mining Cadet Corps in St Petersburg. It establishes the fact that his training at the former, in particular, his acquaintance with V.Y.Sojymonov, con-tributed to the beginning of his connection with the Mining Cadet Corps. A notable event in Hum-boldt s life, which helped to establish and further develop those contacts, was his trip to the Urals and Siberia, where he met and worked with alumni and staff of the Mining Cadet Corps – P.P.Anosov, E.K.Hoffman, D.S.Menshenin, and G.P.Gelmersen. A number of Humboldt’s arti-cles, published in a scientific journal of the Corps «The Mining Journal», testify to those meetings. The article provides a conclusion, which is of great current interest, in connection with the anniversaries: 250 th anniversary of Freiberg Mining Academy; 240 th anniversary of the Mining Cadet Corps (nowadays – the National Mineral Resources University «The Mining University»), and 190 th anniversary of «The Mining Journal», - that those two core European educational institu-tions with the mining and geological specialization, in close and productive interaction played a key role in Humboldt’s life and professional activity.
-
Date submitted2014-12-29
-
Date accepted2015-02-15
-
Date published2015-12-25
A study of distillates physical and chemical properties and residues after thermodestructive and catalytic processes and their application in the mining industry
- Authors:
- N. K. Kondrasheva
- O. V. Zyrianova
When transporting overburden rocks in a cold season, the lower layer of materials freezes to working surfaces of transport equipment, and at long transportations – congeals under its own weight. As a result, up to 50 % of rock remains in the vehicle, while the unloaded part represents indiscreete frozen mass. It considerably complicates the process of unloading transport and leads to increased labor and financial expenses. A rational and effective remedy for these problems is transport equipment and bulk material processing with chemical agents of oil and petrochemical origin – mixtures of distillate and bottom frations obtained as a result of thermodestructive processes during petroleum feedstock manufacturing. The article presents data on the quality of distillates and residual products of oil recycling, which are used as initial components for producing preventive drugs, which are used to prevent sticking and freezing of overburden rocks during transportation and storage in the cold time of year, as well as drugs used for pit roads treatment in surface mining operations. Optimal component compositions of new petrochemicals are developed, and the physical and chemical properties of the received test samples have been studied.
-
Date submitted2010-07-13
-
Date accepted2010-09-13
-
Date published2011-03-21
Actual ways of increasing the effectiveness of facilities for hydrotransport mountain companies
- Authors:
- A. A. Velnikovskiy
Shown the necessity of improving hydrotransport installations. Built a functional model of the hydrotransport system. As a result of its analysis identified the most relevant ways to improve efficiency of hydrotransport on mining enterprises.
-
Date submitted2008-10-18
-
Date accepted2008-12-24
-
Date published2009-12-11
Higher efficiency in drilling of oil and gas wells under complicated conditions
- Authors:
- N. I. Nikolaev
- A. I. Ivanov
The results of researches of properties of the new native waterswelling polymer «Petrosorb» are given. Description is given to the design of plugging-up tool for liquidation of catastrophic absorption of flushing fluid in the course of drilling of oil and gas wells.