-
Date submitted2024-03-20
-
Date accepted2024-11-07
-
Date published2025-04-25
Analysis of the stress state of rocks transformation near a horizontal well during acid treatment based on numerical simulation
The article presents an overview of the assessment and modelling of the stress state of rocks in the near-wellbore zone of horizontal wells during acid stimulation of the formation for improving the efficiency of oil and gas field development. A numerical finite element model of near-wellbore zone of the reservoir drilled by a horizontal section was compiled using one of oil fields in the Perm Territory as an example. The distribution of physical and mechanical properties of the terrigenous reservoir near the well was determined considering transformation under the action of mud acid for different time periods of its injection. Multivariate numerical simulation was performed and the distribution of horizontal and vertical stresses in near-wellbore zone was determined with regard for different values of pressure drawdown and changes in stress-strain properties depending on the area of mud acid infiltration. It was found that a change in elastic modulus and Poisson's ratio under the influence of acid led to a decrease in stresses in near-wellbore zone. Analysis of the stress distribution field based on the Coulomb – Mohr criterion showed that the minimum safety factor of rock even after the effect of mud acid was 1.5; thus, under the considered conditions of horizontal well modelling, the reservoir rock remained stable, and no zones of rock destruction appeared.
-
Date submitted2021-02-09
-
Date accepted2023-09-20
-
Date published2024-02-29
Analysis of experience in the use of preformed particle polymer gels in the development of high-water-cut production facilities in low-temperature oil reservoirs
- Authors:
- Sergei V. Galkin
- Yuliya A. Rozhkova
Foreign practice of oil production in high-water-cut conditions suggests using the technology of injection of preformed particle gel (PPG) suspension into injection wells. After swelling, the polymer particles become elastic and are able to penetrate through highly permeable watered intervals into the remote reservoir zone, forming a polymer “plug”. Thus far, the domestic experience of application of this technology boiled down to testing foreign compounds. We have looked into the possibilities of PPG technology application in geological and technological conditions of high-water-cut fields of Perm Krai. The paper proposes PPG reagents effective in low-temperature reservoirs (20-35 °С) and at relatively high salinity of formation water (more than 200 g/l). The world experience of PPG technology application was analyzed to identify the principal scheme of reagent injection, to establish variants of sequence of injection of PPG particles of different sizes, as well as the possibility of regulating the morphological characteristics of polymer gel particles during synthesis depending on the porosity and permeability of the reservoir. A prerequisite for the technology is the ability to remove PPG particles after treatment from the bottom-hole zone of the formation; for this purpose, tests were carried out on a breaker compound based on sodium persulfate with synergizing additives. PPG technology is effective in reservoirs with high permeability heterogeneity. Two types of high-water-cut production facilities potentially promising for PPG realization have been identified for oil fields of Perm Krai. The first type includes carbonate Tournaisian-Famennian reservoirs with pronounced macrofracturing, in which the PPGs are used for colmatation of flushed large fractures. The second type is terrigenous Visean deposits with increased oil viscosity from 5 to 100 mPa∙s and high permeability of reservoirs (> 0.5 μm2). For both types of reservoirs, areas have been selected that are promising for the implementation of PPG technology.
-
Date submitted2022-09-15
-
Date accepted2022-11-17
-
Date published2022-12-29
Comprehensive assessment of hydraulic fracturing technology efficiency for well construction during hydrocarbon production
The oil and gas industry has been an integral and fundamental sector of the Russian economy for the past few years. The main problems of this industry have traditionally been the deteriorating structure of oil reserves; depreciation of main assets; slowdown and decline in oil production. Recently these have been complicated by a number of new negative trends related to underinvestment, limited financial resources, deteriorating access to new equipment and technologies. The task of the research is to make a comprehensive assessment of hydraulic fracturing technology during well construction and to increase the recovery and intensification of hydrocarbons production. In this research, modeling techniques were used to assess the productivity of each fracture. Geophysical methods (seismic survey) were used to determine the geomechanical properties of the formation. Comprehensive assessment of hydraulic fracturing technology during well construction was carried out, which allowed to increase vertical permeability and unite disparate parts of the reservoir in practice, and to determine the development efficiency of the hydrocarbon field.
-
Date submitted2021-07-05
-
Date accepted2022-11-17
-
Date published2022-12-29
Determination of suitable distance between methane drainage stations in Tabas mechanized coal mine (Iran) based on theoretical calculations and field investigation
A large amount of gas is emitted during underground mining processes, so mining productivity decreases and safety risks increase. Efficient methane drainage from the coal seam and surrounding rocks in underground mines not only improves safety but also leads to higher productivity. Methane drainage must be performed when the ventilation air cannot dilute the methane emissions in the mine to a level below the allowed limits. The cross-measure borehole method is one of the methane drainage methods that involves drilling boreholes from the tailgate roadway to an un-stressed zone in the roof or floor stratum of a mined seam. This is the main method used in Tabas coal mine N 1. One of the effective parameters in this method is the distance between methane drainage stations, which has a direct effect on the length of boreholes required for drainage. This study was based on the measurement of ventilation air methane by methane sensors and anemometers placed at the longwall panel as well as measuring the amount of methane drainage. Moreover, in this study, the obtained and analyzed data were used to determine the suitable distance between methane drainage stations based on the cross-measure borehole method. In a field test, three borehole arrangements with different station distances in Panel E4 of Tabas coal mine N 1 were investigated. Then, the amounts of gas drained from these arrangements were compared with each other. The highest methane drainage efficiency was achieved for distances in the range of 9-12 m between methane drainage stations.
-
Date submitted2021-12-19
-
Date accepted2022-05-13
-
Date published2022-07-13
Development of a pump-ejector system for SWAG injection into reservoir using associated petroleum gas from the annulus space of production wells
Implementation of SWAG technology by means of water-gas mixtures is a promising method of enhanced oil recovery. The use of associated petroleum gas as a gas component in the water-gas mixture allows to significantly reduce the amount of irrationally consumed gas and carbon footprint. Relevant task is to choose a simple, reliable and convenient equipment that can operate under rapidly changing operating conditions. Such equipment are pump-ejector systems. In order to create water-gas mixture it is proposed to use associated gas from the annulus space. This solution will reduce the pressure in the annulus space of the production well, prevent supply disruption and failure of well equipment. The paper presents a principal technological scheme of the pump-ejector system, taking into account the withdrawal of gas from the annulus space of several production wells. The layout of the proposed system enables more efficient implementation of the proposed technology, which expands the area of its application. Experimental investigations of pressure and energy characteristics of the ejector have been carried out. Analysis of the obtained data showed that it was possible to increase the value of maximum efficiency. The possibility of adapting the system in a wide range of changes in operating parameters has been established. Recommendations on selection of a booster pump depending on the values of working pressure and gas content are given.
-
Date submitted2020-05-12
-
Date accepted2020-09-22
-
Date published2020-11-24
Design features of coal mines ventilation using a room-and-pillar development system
- Authors:
- Sergey S. Kobylkin
- Alexander R. Kharisov
The safety of mining operations in coal mines for aerological factors depends on the quality of accepted and implemented ventilation design solutions. The current “Design Manual of coal mine ventilation” do not take into account the features of room-and-pillar development systems used in Russia. This increases the risk of explosions, fires, and gassing. The detailed study of foreign experience in designing ventilation for the considered development systems e of coal deposits allowed to formulate recommendations on the ventilation scheme organization for coal mines using a room-and-pillar development system and the procedure for ventilation during multi-entry gateroad development. Observations have shown that the use of the existing Russian procedure for airing mining sites with a room-and-pillar development system complicates the emergency rescue operations conduct. Low speeds and multidirectional air movement, difficult heat outflow, and the abandonment of coal pillars increase the risk of occurrence and late detection of endogenous fire. The results of numerical modeling have shown that the installation (parallel to the drifts) of ventilation structures in inter-chamber pillars will increase the reliability of ventilation by transferring the ventilation scheme from a complex diagonal to a complex parallel. It will also reduce the amount of air required for the mine site and the total aerodynamic drag. The research made it possible to formulate requirements for the design procedure for coal mines ventilation using a room-and-pillar development system, which consist in the order of working out blocks in the panel, and also the additional use of ventilation structures (light brattice clothes or blowing line brattice).
-
Date submitted2019-12-20
-
Date accepted2020-09-01
-
Date published2020-10-08
Features of the underground storages construction in depleted oil and gas condensate fields
The paper considers the features of the underground storages (US) construction in depleted oil and gas condensate fields (DOGCFs). The requirements for the structure of the formation, corresponding to the parameters of the object for possible US creation are presented. The influence of geological, hydrogeological, mining and technical rock formation conditions on the reliability and tightness of underground storages, including underground gas storages, has been evaluated. The necessary conditions for the US design are analyzed at the example of the Ach-Su oil and gas condensate field, in the presence of a well-explored trap with acceptable parameters for the construction of an underground storage. An important aspect is the geological conditions that meet the criteria for selecting the object: the required structure, the absence of fracturing faults, high reservoir properties of the formation, a sufficient volume of the deposit for the storage. Geological conditions lay the basis for determining the individual characteristics of the US construction technology at each DOGCF. The refined results for the current gas-saturated pore volume and the rate of pressure drop in the formation are presented, which makes it possible to select improved technological indicators in the course of operation of the created US. In order to select the optimal option for the design and construction of the US, the results of economic and geological scenarios analysis were studied concurrently with the capabilities of the technological operation of the object and transport system, which can ensure the maximum daily production of the storage.
-
Date submitted2020-06-15
-
Date accepted2020-06-15
-
Date published2020-06-30
Description of steady inflow of fluid to wells with different configurations and various partial drilling-in
- Authors:
- Valery A. Iktissanov
There are many equations of steady inflow of fluid to the wells depending on the type of well, presence or absence of artificial or natural fractures passing through the well, different degrees of drilling-in of the wellbores. For some complex cases, analytical solutions describing the inflow of fluid to the well have not yet been obtained. An alternative to many equations is the use of numerical methods, but this approach has a significant disadvantage – a considerable counting time. In this regard, it is important to develop a more general analytical approach to describe different types of wells with different formation drilling-in and presence or absence of fractures. Creation of this method is possible during modeling of fractures by a set of nodes-vertical wells passing from a roof to floor, and modeling of a wellbore (wellbores, perforation) by a set of nodes – spheres close to each other. As a result, based on this approach, a calculation algorithm was developed and widely tested, in which total inflow to the well consists of the flow rate of each node taking into account the interference between the nodes and considering the impermeable roof and floor of the formation. Performed modeling confirmed a number of known patterns for horizontal wells, perforation, partial drilling-in of a formation, and also allowed solving a number of problems.
-
Date submitted2019-08-08
-
Date accepted2019-09-16
-
Date published2020-02-25
Testing of preformed particles polymer gel technology on core filtration models to limit water inflows
In order to reduce watering of wells and equalize their injectivity profiles, the prospects of introducing PPG technology in Russian fields are considered, in which preformed particles polymer gel are pumped into the injection well. These particles, being a supersorbent based on polyacrylamide, absorb water, become elastic, which allows them to shrink and tear in narrow filtration channels. When the polymer is filtered along permeable layers saturated with water, polymer particles accumulate in waterlogged intervals and thus they form a polymer plug, which redistributes the filtration flows and increases the coverage of the formation by the process of oil displacement. More than 4000 downhole operations have been carried out in the fields of China and the USA using PPG technology by now. In domestic fields in Western Siberia, there is limited experience in applying a similar technology in high-temperature formations with low mineralization of formation water. Due to the absence of hydrolytic processes in polyacrylamide, well-known domestic compositions are not applicable due to the low absorption capacity in the conditions of low-temperature deposits with increased mineralization of formation water. The authors synthesized a polymer based on polyacrylamide by block polymerization, which allows to obtain a high absorption capacity, including for low-temperature formations with high mineralization of formation water, which is typical for Perm Territory fields. Filtration experiments were carried out on core models with the composition developed by the authors, this composition focused on low formation temperatures and high mineralization of formation water. As a result of the experiments, it was found that the swollen particles of the gel are able to pass into fractures with a diameter less than their own size at least 20 times. With a significant increase in the viscosity of the dispersion medium, the stability of the suspension increases. Particles of polymer gel have the necessary strength for injection in the field conditions. The fracture permeability during polymer injection decreases by several times and becomes comparable with the permeability of pore collectors.
-
Date submitted2019-05-26
-
Date accepted2019-07-23
-
Date published2019-10-23
Ensuring Stability of Undermining Inclined Drainage Holes During Intensive Development of Multiple Gas-Bearing Coal Layers
At high rates of production face advance, requirements towards reliable operation of undermining drainage holes get raised. The issue of maintaining high intensity of gaseous seams development under naturally increasing gas content, mining depth and capacity of production equipment poses a problem. The greatest threat comes from the loss of hole stability in the bearing pressure affected zone (in front of the face) and in the intensive shift area of overhanging rock corbels (behind the face). Intensification of air leaks due to deformation of borehole channel leads to impoverishment of removed methane-air mixture and an increasing risk to disturb safe aerogas regime in the mining area. The paper describes a mechanism of how coal-face operations affect the state of underground holes and formation of overhanging rock corbels. A typification of basic kinds of borehole deformations is presented. Authors point out critical disadvantages of the most widely-used technological schemes of gaseous seams development under high load on the production face, which hinder normal operation of a gas drainage system. As a result of research, a dependency of shot hole number, as well as the distance between shot hole axes and the borehole, on the stress state of the borehole outline has been defined more precisely. Basing on that, a formula to calculate drilling parameters of the discharge hole system has been suggested. Implementation of these measures will allow to increase the efficiency of underground gas drainage and to maintain growing intensity of gaseous coal seam development.
-
Date submitted2019-01-11
-
Date accepted2019-03-17
-
Date published2019-06-25
Improving methods of frozen wall state prediction for mine shafts under construction using distributed temperature measurements in test wells
- Authors:
- L. Yu. Levin
- M. A. Semin
- O. S. Parshakov
Development of mineral deposits under complex geological and hydrogeological conditions is often associated with the need to utilize specific approaches to mine shaft construction. The most reliable and universally applicable method of shaft sinking is artificial rock freezing – creation of a frozen wall around the designed mine shaft. Protected by this artificial construction, further mining operations take place. Notably, mining operations are permitted only after a closed-loop frozen section of specified thickness is formed. Beside that, on-line monitoring over the state of frozen rock mass must be organized. The practice of mine construction under complex hydrogeological conditions by means of artificial freezing demonstrates that modern technologies of point-by-point and distributed temperature measurements in test wells do not detect actual frozen wall parameters. Neither do current theoretical models and calculation methods of rock mass thermal behavior under artificial freezing provide an adequate forecast of frozen wall characteristics, if the input data has poor accuracy. The study proposes a monitoring system, which combines test measurements and theoretical calculations of frozen wall parameters. This approach allows to compare experimentally obtained and theoretically calculated rock mass temperatures in test wells and to assess the difference. Basing on this temperature difference, parameters of the mathematical model get adjusted by stating an inverse Stefan problem, its regularization and subsequent numerical solution.
-
Date submitted2018-11-03
-
Date accepted2019-01-21
-
Date published2019-04-23
Estimation of critical depth of deposits by rock bump hazard condition
- Authors:
- V. N. Tyupin
During the development of minerals by the underground method, dynamic manifestations of rock pressure occur at a certain depth, which significantly reduces the safety of mining operations. Regulatory documents prescribe at the exploration and design stages to establish the critical depth for classifying a deposit as liable to rock bumps. Currently, there are a number, mainly instrumental, methods for determining the liability of rock mass to rock bumps and methods based on the determination of physical and technical properties and the stress-strain state of rock massifs. The paper proposes a theoretical method for determining the critical depth for classifying a deposit as liable to rock bumps. A formula for determining the critical depth of the rock bump hazard condition is obtained. A mathematical analysis of the influence of the physical and technical parameters of the formula on the critical depth is carried out. Its physical and mathematical validity is substantiated. The numerical calculations of the critical depth for 17 developed fields were carried out using a simplified formula. It also provides a comparison of calculated and actual critical depth values. It is established that the variation of the actual and calculated critical depth is due to the lack of actual data on the value of the friction coefficient and parameters of fracturing of the rock mass in the simplified formula. A simplified calculation formula can be used to estimate the critical depth of a field at the survey and design stages. More accurate results can be obtained if there are actual data on fracture parameters, friction coefficients and stress concentration near the working areas.
-
Date submitted2018-11-18
-
Date accepted2019-01-17
-
Date published2019-04-23
Calculation of elastoviscoplastic displacement of well walls in transversal and isotropic rocks
- Authors:
- A. G. Gubaidullin
- A. I. Moguchev
The relevance of the work is justified by the need to improve the technical and economic indicators of well construction based on forecasting and preventing drilling tools sticking due to the narrowing of an open well bore in the intervals of transversely isotropic rocks. A mathematical model of elastic-viscous-plastic displacement of the walls of inclined and horizontal wells has been developed during the narrowing of the open borehole due to rock creep in the intervals of transversely isotropic rocks. In the program developed based on this mathematical model, the calculation of the elastic-viscous-plastic displacement of the walls of an obliquely directed and horizontal well in the reservoir of argillite from the Western Siberia deposit was carried out. As a result of the calculation, it was established that after opening the rock with bits, the cross-section of the open borehole due to the rock creep eventually takes the form of an ellipse, the small axis of which is in the plane of the upper wall of the well and decreases with time.
-
Date submitted2018-11-09
-
Date accepted2019-01-22
-
Date published2019-04-23
Determining the stability of the borehole walls at drilling intervals of loosely coupled rocks considering zenith angle
- Authors:
- P. A. Blinov
During development of drilling projects, a whole array of data is needed considering the properties of rocks and the conditions of their bedding. Accounting for geomechanical processes occurring in the near-wellbore zone allows avoiding many complications associated with the violation of the wellbore walls stability at all stages of its construction and operation. Technological and technical factors such as vibration and rotation of the drilling string, formation of launders during the descent and ascent of the assembly, pressure pulsation during the start and stop of pumps, hydrostatic and hydrodynamic pressure of the drilling fluid, its composition and properties, have a great influence on the stress-strain state of the medium opened by the well. The washing fluid circulating in the well should provide backpressure to the reservoir, not interact with the rocks chemically, colmatage channels in porous and fractured rocks, preventing penetration of the mud into the medium, by creating an impermeable barrier at drilling clay seams that are prone to swelling, cracking, etc. The article discusses the method for determining the stability of the directed well walls, taking into account the penetration of drilling mud into the pores and fractures of rocks. The technique will allow adjusting the zenith angle of the well during the workout of an unstable interval at the design stage, or selecting a drilling fluid composition to ensure fail-safe drilling.
-
Date submitted2018-01-17
-
Date accepted2018-03-09
-
Date published2018-06-22
Control and regulation of the hydrochloric acid treatment of the bottomhole zone based on field-geological data
- Authors:
- M. K. Rogachev
- V. V. Mukhametshin
The analysis results of the hydrochloric acid treatment of the bottomhole zone efficiency along the deposits of high-viscosity oil in the carbonate reservoirs of the Tournaisian stage are presented in the paper. Based on the use of the non-parametric Kulbak criterion, the most informative geological and technological parameters, which affect most the success of hydrochloric acid treatments, assessed by the criteria of increased oil production and reduced water cut, are revealed. The generalization of the hydrochloric acid treatments experience in the conditions of the high-viscosity oil reservoirs of the Tournaisian Stage allows for efficient forecasting, selection of wells, control and regulation of the treatment process to reduce the number of inefficient operations and improve the technical and economic parameters of fuel and energy enterprises at the investigated sites and the ones with similar field-geological characteristics.
-
Date submitted2018-01-15
-
Date accepted2018-03-24
-
Date published2018-06-22
Designing of well trajectory for efficient drilling by rotary controlled systems
- Authors:
- M. V. Dvoinikov
The main directions of increasing the efficiency of drilling wells by improving methods for designing profiles of directional and horizontal wells are identified. The feasibility and necessity of using at drilling with rotary controlled systems the trajectories of directed wells' profiles with continuous curving, that do not contain conjugated sections, on the basis of plane transcendental curves are theoretically substantiated and experimentally confirmed. An algorithm and software are developed that allow optimal selection of a profile or a trajectory section, taking into account minimization of twisting, bending, compressive and tensile stresses that ensure the efficiency of technical and technological parameters of well drilling.
-
Date submitted2016-11-16
-
Date accepted2017-01-01
-
Date published2017-04-14
Complex use of heat-exchange tunnels
- Authors:
- A. F. Galkin
The paper presents separate results of complex research (experimental and theoretical) on the application of heat-exchange tunnels – in frozen rocks, among other things – as underground constructions serving two purposes. It is proposed to use heat-exchange tunnels as a separate multi-functional module, which under normal conditions will be used to set standards of heat regime parameters in the mines, and in emergency situations, natural or man-made, will serve as a protective structure to shelter mine workers. Heat-exchange modules can be made from mined-out or specially constructed tunnels. Economic analysis shows that the use of such multi-functional modules does not increase operation and maintenance costs, but enhances safety of mining operations and reliability in case of emergency situations. There are numerous theoretic and experimental investigations in the field of complex use of mining tunnels, which allows to develop regulatory design documents on their basis. Experience of practical application of heat-exchange tunnels has been assessed from the position of regulating heat regime in the mines.
-
Date submitted2016-09-22
-
Date accepted2016-11-14
-
Date published2017-02-22
Technological problems and fundamental principles of methods of engineering-geocryological exploration during construction and exploitation of wells in permafrost rock mass
- Authors:
- Z. N. Cherkai
- E. B. Gridina
The article describes peculiarities and complicating factors when constructing wells in cryolithic zones. It also presents fundamental principles of methods of pilot parametric drilling for complex exploration of engineering-geocryological conditions of multiple-well gas production platforms. The article describes peculiarities of geophysical examinations within the complex of parametric drilling for clarification and correlation of log sheet, and identifying non-commercial gas reservoirs and interpermafrost head oil-filed water horizons in permafrost rock mass. We defined main ecological issues of parametric drilling and presented potential environment pollutants from well drilling in cryolithic zones. It concludes a list of factors, which should be considered during gas well drilling in northern zones for meeting the «safety – sustainability – low waste» criteria.
-
Date submitted2014-12-10
-
Date accepted2015-02-20
-
Date published2015-12-25
Opencast mine parameters sensitivity analysis at preliminary study of a mining project
- Authors:
- S. I. Fomin
- E. I. Bazarova
The article describes sensitivity analysis, aimed at variables dependence detection: to what extent open cast mine ultimate efficiency or performance will be affected when one of the key input variables is changed. The stronger the dependence effect, the higher the project implementation risk. The sensitivity analysis objective is demonstrated – principle factors identification – critical variables, capable of having a serious influence on the project implementation results, and impact verification of progressive (single) factorial changes. Sensitivity analysis in its content is a single-factor analysis. Output, as a basic performance indicator of an open cast mine, characterizes mine development intensity and is determined by mining-engineering and economic factors. It is proved that the impact degree from various parameters on the open cast mine output is characterized by elasticity ratio. The project indicators sensitivity analysis, which was carried out, allowed to establish the impact degree that various parameters have on the open cast mine output, which takes place in a high-angle ore deposit, characterized by elasticity ratio.
-
Date submitted2014-11-01
-
Date accepted2015-01-18
-
Date published2015-10-26
On the design features of underground multiple gassy coal seam mining
- Authors:
- O. I. Kazanin
The analysis of the industry regulatory requirements and the world design experience of underground multiple coal seam mining is provided. The main problems of intensive longwall mining of multiple flat gassy coal seams as well as methods for determination of high rock pressure zone parameters and seams interaction are considered. The examples of a number of mines in the Kuzbass and Pechora coal basins show that the design of multiple seam mining and the choice of longwall panel parameters were often made without taking into consideration influence of surrounded seams that leads to essential complication of conditions for mining operations and decreases the technical and economic indicators of mining. The existing industry regulations do not allow considering complex influence of factors in multiple coal seams mining fully. On the basis of field, laboratory, and numeric research results it is noted that recommendations for pillar positioning in contiguous seams ensuring efficiency and safety of multiple seam longwall mining can significantly differ in case of liability of coal seams to spontaneous combustion, high natural gas content, influence of multiple seam mining onto daily surface, and difficult conditions of entries maintenance. The importance of having information on the stress-strain condition of the rock mass at a design stage and its changes in the process of multiple seam mining is shown. The need for industry regulations updating for the purpose of a more detailed definition of a form, size and a location of high rock pressure zones as well as stress parameters in these zones is noted. A set of recommendations for effective and safe multiple seam mining is developed.
-
Date submitted2009-10-11
-
Date accepted2009-12-26
-
Date published2010-09-22
The analysis of factors, that cause processes of open hole wells’ destructions of Gatchina underground gas storage reservoir and prediction of sand effects
- Authors:
- D. V. Grishin
- A. V. Petukhov
- A. A. Petukhov
The peculiarities of elastic stresses in open hole wells’ of Gatchina gas storage reservoir are researched. It is revealed that in depression more than 1,5 MPa gas bearing rocks start to destroy. On the basis of studying of correlation relation between technological parameters of gas wells’ production and evacuation of sand the equations of plural regression are constructed. These equations are used to make prediction of sand evacuation at each producing gas well.
-
Date submitted2009-10-06
-
Date accepted2009-12-30
-
Date published2010-09-22
Research of deformation, strength and filtration characteristics of Nizhnechutinskoe oil field’s reservoirs in case of depression making in the process of oilwells exploitation
- Authors:
- A. V. Petukhov
- A. A. Petukhov
It is determined that main reasons of permeability reservoirs decrease in Nizhnechutinskoe oil field are capillary pressures and elastic stresses, appearing at depression making. It is displayed that to reduce tangential stresses in oil bearing reservoirs it is expedient to make vertical slits in oilwells’ open holes.
-
Date submitted2009-10-12
-
Date accepted2009-12-19
-
Date published2010-09-22
Preventive measures of gas-dynamic phenomena in the workings drivage on the rockburst- outburst-hazardous seams under extremely complicated geological and mining conditions
- Authors:
- V. P. Kostromin
A complex of measures preventing the manifestation of rockbursts and sudden outbursts of coal and gas has been developed. Criteria of forecasting, an assessment of efficiency of the preventive measures are suggested, as well as the necessary technical facilities and technologies.
-
Date submitted2009-07-28
-
Date accepted2009-09-14
-
Date published2010-04-22
The use of computer technologies аt the stages of prospecting, mining and conservation of mineral deposits
- Authors:
- K. V. Morozov
- S. V. Lukichev
The article described the methods for the use of specialized application of software on the stages of exploration, design, planning and maintenance of mining operations and also in abandonment or conservation of mineral resources deposits.
-
Date submitted2009-07-17
-
Date accepted2009-09-22
-
Date published2010-04-22
MINEFRAME is the modern tool for mining maintenance
- Authors:
- L. S. Lomako
- G. G. Korol
Today an automation of the basic technological processes in production is successfully introduced into various sectors of the national economy, including in mining practice. One of the modern software products intended for automated planning, designing and support of works at the mining enterprises, is integrated package – MINEFRAME which is put in industrial operation.