-
Date submitted2024-03-20
-
Date accepted2024-11-07
-
Date published2025-02-27
Analysis of the stress state of rocks transformation near a horizontal well during acid treatment based on numerical simulation
The article presents an overview of the assessment and modelling of the stress state of rocks in the near-wellbore zone of horizontal wells during acid stimulation of the formation for improving the efficiency of oil and gas field development. A numerical finite element model of near-wellbore zone of the reservoir drilled by a horizontal section was compiled using one of oil fields in the Perm Territory as an example. The distribution of physical and mechanical properties of the terrigenous reservoir near the well was determined considering transformation under the action of mud acid for different time periods of its injection. Multivariate numerical simulation was performed and the distribution of horizontal and vertical stresses in near-wellbore zone was determined with regard for different values of pressure drawdown and changes in stress-strain properties depending on the area of mud acid infiltration. It was found that a change in elastic modulus and Poisson's ratio under the influence of acid led to a decrease in stresses in near-wellbore zone. Analysis of the stress distribution field based on the Coulomb – Mohr criterion showed that the minimum safety factor of rock even after the effect of mud acid was 1.5; thus, under the considered conditions of horizontal well modelling, the reservoir rock remained stable, and no zones of rock destruction appeared.
-
Date submitted2022-03-01
-
Date accepted2024-06-03
-
Date published2024-12-25
Study of the possibility of using high mineralization water for hydraulic fracturing
The results of laboratory studies aimed at developing hydraulic fracturing fluid based on alternative sources of high mineralization water are presented. It is shown that Cenomanian sources have the most stable mineralization parameters, while bottom water and mixed waters collected from pressure maintenance systems differ significantly in their properties, with iron content varying several times, and hardness and mineralization undergoing substantial changes. The quality of the examined hydraulic fracturing fluids based on alternative water sources is confirmed by their impact on residual permeability, as well as residual proppant pack conductivity and permeability. The experimental results show similar values for these parameters. The comprehensive laboratory studies confirm the potential for industrial use of high mineralization water in hydraulic fracturing operations.
-
Date submitted2022-10-04
-
Date accepted2024-03-05
-
Date published2024-08-26
Localization and involvement in development of residual recoverable reserves of a multilayer oil field
During waterflooding of a multilayer oil field there is a constant deterioration of the structure and composition of residual reserves due to geological and technological reasons. The largest share of residual reserves is localized in pillars, which arise from uneven development of the production facility and are undrained or poorly drained zones. The results of a quantitative assessment of the distribution of residual oil reserves in the Middle and Upper Devonian deposits of the Romashkinskoe oil field of the Republic of Tatarstan are presented. A retrospective method is proposed to identify reserves by analyzing and summarizing historical exploration data and the long history of reservoir development, and a calculation algorithm is proposed to quantify them. It has been established that residual oil reserves are localized in rows of dividing and injection wells, as well as in the central rows of producing wells in a three-line drive, in abandoned and piezometric wells, in the areas adjacent to the zones of reservoir confluence, pinch-out, oil-bearing contours, distribution of reservoirs with deteriorated porosity and permeability properties. Depending on geological conditions, algorithms for selecting geological and technical measures to include localized reserves in development and forecasting production profiles were proposed. According to the proposed method, residual recoverable reserves were identified and a number of wells were recommended for experimental works on their additional recovery: in well 16 (hereinafter in the text, conventional well numbers are used) after isolation of overlying high-water-cut formations, the additional perforation was carried out and oil flow was obtained. Additional perforation in well 6 resulted in oil recovery during development as well. Thus, the developed approaches to identifying residual recoverable reserves and patterns of their spatial distribution can be recommended in other multilayer oil fields with a long history of development.
-
Date submitted2022-09-30
-
Date accepted2023-04-03
-
Date published2024-02-29
Optimization of the location of a multilateral well in a thin oil rim, complicated by the presence of an extensive gas cap
- Authors:
- Кirill О. Тomskii
- Mariya S. Ivanova
The specific share of the reserves of hard-to-recover hydrocarbon raw materials is steadily growing. The search for technologies to increase the hydrocarbon recovery factor is one of the most urgent tasks facing the oil and gas industry. One of the methods to expand the coverage of oil reserves and increase oil recovery is to use the technology of drilling multilateral wells with a fishbone trajectory. In the Russian Federation, the most branched well was drilled in the Republic of Sakha (Yakutia) at the Srednebotuobinskoye oil and gas condensate field. The main object of development is the Botuobinsky horizon (Bt reservoir). About 75 % of the geological reserves of the reservoir are concentrated in a thin oil rim with an average oil-saturated layer thickness of 10 m with an extensive gas cap. This circumstance is one of the main complicating factors in the development of the Srednebotuobinskoye oil and gas condensate field. For such complex wells, one of the most important design stages is to determine the optimal location of the fishbone well in an oil-saturated reservoir. The article shows the results of sector modeling in the conditions of the Srednebotuobinskoye field to determine the optimal location of multilateral wells using Tempest simulator.
-
Date submitted2022-04-12
-
Date accepted2022-11-17
-
Date published2022-12-29
Development of technological solutions for reliable killing of wells by temporarily blocking a productive formation under ALRP conditions (on the example of the Cenomanian gas deposits)
Modern field operation conditions are characterized by a decline in gas production due to the depletion of its reserves, a decrease in reservoir pressure, an increase in water cut, as well as due to the depreciation of the operating well stock. These problems are especially specific at the late stage of development of the Cenomanian deposits of Western Siberia fields, where the anomaly factor below 0.2 prevails, while gas-bearing formations are represented mainly by complex reservoirs with high-permeability areas. When killing such wells, the classical reduction of overbalance by reducing the density of the process fluid does not provide the necessary efficiency, which requires the search for new technical and technological solutions. In order to prevent the destruction of the reservoir and preserve its reservoir properties during repair work in wells with abnormally low reservoir pressure, AO “SevKavNIPIgaz” developed compositions of special process fluids. A quantitative description of the process of blocking the bottomhole formation zone is proposed by means of mathematical modeling of injection of a gel-forming solution into a productive horizon. The well killing technology includes three main stages of work: leveling the injectivity profile of the productive strata using three-phase foam, pumping the blocking composition and its displacement with the creation of a calculated repression. Solutions obtained on the basis of a mathematical model allow optimizing technological parameters to minimize negative consequences in the well killing process.
-
Date submitted2021-09-01
-
Date accepted2022-10-07
-
Date published2022-12-29
Parameter determination of the method of directional unloading of the reservoir based on physical modelling on a true triaxial loading setup
The article presents a theoretical and experimental substantiation of the method of directional unloading of the reservoir in fields with low-permeability reservoirs. The relevance of the article is due to the reduction of hydrocarbon resources in modern conditions and the need to create new efficient environmentally friendly technologies to develop hydrocarbon deposits with hard-to-recover reserves, primarily with low-permeability reservoirs. The results of a theoretical study of the stress-strain state in the vicinity of a well, both cased and open, are presented. They are necessary to develop programs for laboratory testing of core specimens from the studied fields. A technique for physical modelling of deformation processes in the bottomhole zone with a decrease in pressure at the well bottom in a true triaxial loading unit is described in order to determine the parameters of the process impact on the formation reservoir, leading to an increase in well productivity. The method was applied to the conditions of the low-permeability reservoir at the Verkhneviluchanskoye oil and gas condensate field in the southwest of the Republic of Sakha (Yakutia). Expe-rimental studies were carried out on a unique scientific unit for true triaxial loading, created at the IPMech RAS, the Triaxial Independent Loading Test System. The directional unloading method was adapted for the studied field, the process parameters of successful application of the method were determined: the bottomhole design, the drawdown values necessary to increase the permeability of the bottomhole formation zone.
-
Date submitted2021-10-18
-
Date accepted2022-01-24
-
Date published2022-04-29
Development of a hydrocarbon completion system for wells with low bottomhole temperatures for conditions of oil and gas fields in Eastern Siberia
The paper presents the results of investigations on the influence of low bottomhole temperatures in the intervals of productive formations on the technological properties of solutions used for drilling and completion of wells in order to determine the possibility of increasing gas recovery coefficient at the field of the “Sila Sibiri” gas pipeline. The analysis of technological measures determining the quality of the productive horizon drilling-in was carried out. It was found out that the dispersion of bridging agent in the composition of the hydrocarbon-based drilling mud selected from the existing methods does not have significant influence on the change in the depth of filtrate penetration into the formation in conditions of low bottomhole temperatures. The main reason for the decrease in the near-bottomhole zone permeability was found out – the increase in plastic viscosity of the dispersion medium of the hydrocarbon-based drilling mud under the influence of low bottomhole temperatures. A destructor solution for efficient wellbore cleaning from hydrocarbon-based solution components in conditions of low bottomhole temperatures was developed. The paper presents the results of laboratory investigations of hydrocarbon-based drilling mud and the developed destructor solution, as well as its pilot field tests. The mechanism of interaction between the destructor solution and the filter cake of the hydrocarbon-based drilling mud ensuring the reduction of the skin factor in the conditions of the geological and hydrodynamic structure of Botuobinsky, Khamakinsky and Talakhsky horizons of the Chayandinskoye oil and gas condensate field has been scientifically substantiated.
-
Date submitted2021-10-19
-
Date accepted2021-11-30
-
Date published2021-12-27
Potential technological solution for sampling the bottom sediments of the subglacial lake Vostok: relevance and formulation of investigation goals
The subglacial Lake Vostok in Antarctic is a unique natural phenomenon, its comprehensive study involves sampling of water and bottom surface rocks. For further study of the lake, it is necessary to drill a new access well and develop environmentally safe technologies for its exploration. This article discusses existing and potential technologies for sampling bottom surface rocks of subglacial lakes. All these technologies meet environmental safety requirements and are conducive for sampling. The authors have proposed an alternative technology, using a walking device, which, due to its mobility, enables selective sampling of rocks across a large area from a single access well. The principal issues, related to the implementation of the proposed technology, are investigated within this article. This report is prepared by a team of specialists with many years of experience in drilling at the Vostok Station in Antarctic and in experimental work on the design of equipment and non-standard means of mechanization for complicated mining, geological and climatic conditions.
-
Date submitted2021-03-11
-
Date accepted2021-05-21
-
Date published2021-09-20
The influence of solar energy on the development of the mining industry in the Republic of Cuba
Cuba is traditionally considered a country with an underdeveloped industry. The share of the mining and metallurgical industries in the gross industrial production of the republic is small – about 3 % of GDP. The development of deposits and the extraction of nickel ores is an important sector of the economy of the Republic of Cuba, since the largest reserves of nickel and cobalt on the North American continent are located on the territory of the country. The development of the country energy system can serve as a growth factor in this sector of the economy. Due to climatic features and impossibility of integrating new capacities into the energy system through the construction of hydroelectric power plants, solar energy is a promising direction. Determining the feasibility of using solar tracking systems to increase the generation of electricity from solar power plants is one of the main challenges faced by engineers and renewable energy specialists. Currently, there are no solar tracking systems in Cuba that can provide information to assess the effectiveness of this technology in the country. The lack of the necessary technologies, as well as the high cost of developing solar power plants with tracking systems, limit the widespread introduction of such complexes. Hence follows the task of creating an inexpensive experimental model that allows assessing the effectiveness of tracking systems in specific weather conditions of the Republic of Cuba. This model will allow in future to increase the efficiency of electrical complexes with solar power plants, which provide power supply to the objects of the mineral resource complex and other regions.
-
Date submitted2020-05-25
-
Date accepted2020-06-11
-
Date published2020-12-29
Technological aspects of cased wells construction with cyclical-flow transportation of rock
- Authors:
- Andrei S. Kondratenko
A high-performance technology for constructing cased wells is proposed. Essence of the technology is the advance insertion of the casing pipe into the sedimentary rock mass and the cyclical-flow transportation of the soil rock portions using the compressed air pressure supplied to the open bottomhole end of the pipe through a separate line. Results of mathematical modeling for the process of impact insertion of a hollow pipe into a soil mass in horizontal and vertical settings are considered. Modeling of the technology is implemented by the finite element method in the ANSYS Mechanical software. Parameters of the pipe insertion in the sedimentary rock mass are determined - value of the cleaning step and the impact energy required to insert the pipe at a given depth. Calculations were performed for pipes with a diameter from 325 to 730 mm. Insertion coefficient is introduced, which characterizes the resistance of rocks to destruction during the dynamic penetration of the casing pipe in one impact blow of the pneumatic hammer. An overview of the prospects for the application of the proposed technology in geological exploration, when conducting horizontal wells of a small cross-section using a trenchless method of construction and borehole methods of mining, is presented. A variant of using the technology for determining the strength properties of rocks is proposed. Some features of the technology application at industrial facilities of the construction and mining industry are considered: for trenchless laying of underground utilities and for installing starting conductors when constructing degassing wells from the surface in coal deposits. Results of a technical and economic assessment of the proposed technology efficiency when installing starting conductors in sedimentary rocks at mining allotments of coal mines are presented.
-
Date submitted2020-05-13
-
Date accepted2020-11-12
-
Date published2020-12-29
Improving the efficiency of terrigenous oil-saturated reservoir development by the system of oriented selective slotted channels
A comparative assessment of variation in the flow rate of oil production wells was performed taking into account increasing of perforated area of the productive part of the rocks, as well as recover of reservoir rocks permeability due to their unloading by creating slotted channels with the method of oriented slotted hydro-sandblast perforation. Different orientation directions and slotting intervals were analyzed, taking into account water encroachment of individual interlayers and azimuth direction of the majority of remaining reserves in separate blocks of the examined formation. In order to estimate development efficiency of terrigenous oil-saturated porous-type reservoirs by means of oriented slotted hydro-sandblast perforation, calculations were performed on a full-scale geological and hydrodynamic model of an oil field in the Perm Region. The object of modeling was a Visean terrigenous productive forma tion. The modeling of implementing oriented slotted hydro-sandblast perforation was carried out on a 3D filtration model for fourteen marginal wells, located in the zone with excessive density of remaining recoverable reserves and he terogeneous reserve recovery along the section. An optimal layout of slotted channels along the depth of the productive part of the well section was developed. Selective formation of 24 slotted channels was carried out con sidering the intervals of increased oil saturation. Comparative analysis of estimated flow rate of the wells was per formed for cumulative perforation of the examined productive formation and the developed method of slotted perforation. As a result of modeling, an increase in the oil average flow rate of 2.25 t/day was obtained. With oriented slotted hydro-sandblast perforation, incremental cumulative production for two years of prediction calculations per one well reached 0.5 thousand t.
-
Date submitted2019-07-09
-
Date accepted2019-09-26
-
Date published2020-04-24
Development of mathematical models to control the technological properties of cement slurries
Oil and gas producing enterprises are making increasingly high demands on well casing quality, including the actual process of injection and displacement of cement slurry, taking into account requirements for the annular cement level, eliminating possible hydraulic fracturing, with developing a hydraulic cementing program. It is necessary to prevent deep invasion of cement slurry filtrate into the formation to exclude bridging of productive layers. It is impossible to fulfill all these requirements at the same time without application of modifying additives; complex cement compositions are being developed and applied more often. Furthermore, need to adjust cement slurries recipes appears for almost every particular well. In order to select and justify cement slurries recipes and their prompt adjustment, taking into account requirements of well construction project, as well as geological and technical conditions for cementing casing strings, mathematical models of the main technological properties of cement slurries for cementing production casing strings in the Perm Region were developed. Analysis of the effect of polycarboxylic plasticizer (Pl) and a filtration reducer (fluid loss additive) based on hydroxyethyl cellulose (FR) on plastic viscosity (V), spreadability (S) and filtration (F) of cement slurries is conducted. Development of mathematical models is performed according to more than 90 measurements.
-
Date submitted2019-09-25
-
Date accepted2019-12-20
-
Date published2020-04-24
Study of the well near-bottomhole zone permeability during treatment by process fluids
- Authors:
- Evgenii A. Rogov
In the process of drilling-in productive horizons, several irreversible physical and chemical processes take place in the near-wellbore zone of the formation: stress state of the rocks changes, penetration of the filtrate and solid phase, as well as drilling mud into the reservoir, and swelling of clay particles of intergranular cementing material are observed. As a result, permeability of productive horizon is significantly reduced and, consequently, potential inflow of oil or gas from formation is excluded. An equally serious problem exists during well servicing and workover, when the use of irrational fluids of well killing causes negative consequences associated with deterioration of reservoir properties of formations in the wells being repaired. Article presents the results of the experiments on permeability of clayed porous samples after exposure to various compositions of liquids. In order to increase permeability of near-borehole zone of the formation and increase productivity of wells completed by drilling, and after well servicing and workover, a composition of the process fluid containing a 15 % aqueous solution of oxyethylene diphosphonic acid (OEDA) with addition of a surfactant is proposed.
-
Date submitted2019-05-14
-
Date accepted2019-07-05
-
Date published2020-04-24
Development of spacer fluids and cement slurries compositions for lining of wells at high temperatures
Article is devoted to creation of new compositions of process solutions for lining of directional wells at high temperatures. Developed compositions provide high durability characteristics of cement stone. It is shown that with an increase in packing density of cementing slurry components durability characteristics increase and porosity and permeability of cement stone decrease, whereas an increase in temperature and pressure leads to a significant increase in compressive and bending durability, which is associated with presence of quartz in them. It has been established that introduction of special structure-forming additives to the composition of developed cementing solutions allows formation of sedimentation-resistant cement systems that can provide an increase in durability characteristics of cement stone and, in general, quality lining of directional wells. Study of rheological properties of developed cementing compositions showed that the systems have high yield strength at increased temperatures and pressures. Developed compositions of water-based spacer fluids increase the cleansing degree for both casing and rocks surfaces from mud and clay cake residues, which improves the cementing quality of oil and gas wells. Mechanism for increasing the washing ability of spacer fluids and durability characteristics of cement stone, depending on composition and properties of their constituent components, is disclosed.
-
Date submitted2019-05-30
-
Date accepted2019-09-04
-
Date published2020-02-25
Prospects for industrial methane production in the mine n.a. V.M.Bazhanov using vertical surface wells
The estimated methane resources in the coal stratum of Donbass are 798.5 billion m 3 , including 119.5 billion m 3 in the Donetsk-Makeevsky area. Such significant potential implies that methane can be used not only for industrial production and energy purposes but also as a commodity for the chemical industry. However, in practice, commercial production of methane from coal seams, as is done in the fields of the USA, Canada, India, and China, is not carried out, and methane, obtained as a by-product, is utilized for ensuring the safety of the main technological processes for coal mining. The main reasons for this are the difficult mining and geological conditions of bedding, low thickness and permeability, which does not allow to separate methane production into an independent type of activity due to its low profitability, especially with the use of new technologies based on hydraulic fracturing of coal seams. The assessment of the possibility of industrial methane production in the mine n.a. V.M.Bazhanov in the Donetsk-Makeevsky area of Donbass, which reserves equal to 23.7 billion m 3 , showed that a significant part of the methane reserves is concentrated in coal seams and interlayers with a gas content of 18.5-20.7 m 3 /m 3 . Moreover, in the host rocks, methane is practically in a liberated state. This circumstance makes possible the commercial production of methane for its utilization from the unloaded rock mass by wells drilled from the surface, without the use of hydraulic fracturing technology. The paper discusses the technology of methane extraction by a degassing well drilled from the surface into a coal-bearing stratum unloaded from rock pressure in a mining field of the 4th eastern face of the m 3 seam of the mine n.a. V.M.Bazhanov and its subsequent use as the fuel of an electric generator. It is shown that over the entire period of operation of the pilot well, the volume of actually produced methane exceeded the design value by 23 %, and the cost of the gas produced amounted to 1535 rubles per 1000 m 3 , which is more than 3 times lower than the market price for natural gas for consumers in the Russian Federation. This made it possible to make a conclusion about the possibility of industrial extraction of mine methane using vertical surface wells for its subsequent utilization in power plants, which does not imply the usage of hydraulic fracturing technology.
-
Date submitted2020-01-09
-
Date accepted2020-01-17
-
Date published2020-02-25
Methodology for Calculating the Stability of the Polymer Operating String in Permafrost
- Authors:
- V. A. Stetukha
- I. I. Zheleznyak
The goal of this paper is to develop a methodology for calculating the stability of an annular cross-section string casing made of polymer material used for the development of mineral deposits by underground leaching in permafrost formations. The aim was to determine the geometric parameters of the casing and to ensure its operational reliability. The relevance of the research is associated with the peculiarities of external influences on the string, for example, a geotechnological well operating in permafrost formation under conditions of additional exposure to ice pressure during freezing of water in the borehole annulus. This effect is usually accompanied by deformation of the casing due to ice pressure, which can lead to string collapse, abnormal operation and the risk of contamination of the geological environment. The proposed calculation method for a polymer casing is based on simulation of objects using the finite element method. We used the spatial finite elements to model the interaction of key elements of the geotechnological natural-technogenic complex: a polymer casing, ice in the annulus space and homogeneous or heterogeneous rock masses adjacent to the well. The results of the study are presented in the form of tables and patterns of displacements, which reflect stresses and strains in the elements of the calculation scheme. The analysis of the obtained results confirms the possibility of using polymer casings of different technological purposes in various conditions of permafrost formation, including extreme ones. The results of the redistribution of pressure created by ice during the freezing of water in the borehole annulus to the rock mass and the string are evaluated. Interdependent deformations of the rock mass and operating string during freezing of water in the borehole annulus are determined. The necessity of considering the properties of the rock mass in determining the pressure on the string is established. The conditions for the collapse of the string with a different combination of its parameters are revealed.
-
Date submitted2019-01-23
-
Date accepted2019-03-17
-
Date published2019-06-25
Development of the composition of the process fluid to eliminate bit seizure
- Authors:
- E. A. Rogov
During well construction, one of the most complicated types of accidents is the bit seizure as a result of which oil and gas companies incur significant losses due to the abandonment of a portion of the drill string in the well, cutting of an additional wellbore, and sometimes loss of the well. In the case of the elimination of seizure due to packing a positive result can be achieved by pumping portions of the process fluid into the seizure area. Destruction of the packer during the physicochemical effect of the process fluid, in general, allows for complete or partial softening of the packer, changing the pressure in the seizure area and significantly reducing the force required to release the stuck tool. The article presents the results of laboratory studies on the effect of various compositions of process fluids on the packer to eliminate the bit seizure. The effectiveness of the packer destruction was estimated by reducing the tangential stresses after the physicochemical effect of various compositions of process fluids for the same period. A 10% aqueous solution of hydroxyethylidene diphosphonic acid with an addition of 0.5% surfactant alpha olefin sodium sulfonate is recommended as a process fluid to eliminate packer seizures.
-
Date submitted2018-01-04
-
Date accepted2018-03-08
-
Date published2018-06-22
Influence of mining-geological conditions and technogenic factors on blastholes stability during open mining of apatite-nepheline ores
- Authors:
- M. N. Overchenko
- S. A. Tolstunov
- S. P. Mozer
The paper presents the results of borehole stability research and considers possible causes of emergencies. The features of the blast hole drilling process are analyzed taking into account the properties of the rock. Based on the distribution of speed of drill fines removal from the well, an algorithm for selecting drilling modes is proposed. The nature of change in the size of the holess over time has been analyzed. This paper investigates the influence of rock fracturing and its water content on borehole stability. Possible options for eliminating the man-made impact on the massif near holes and options for fixing the hole walls with soft shells are suggested. The experimental data on the installation of shells for the conditions of open mining of apatite-nepheline ores are given. The operability and effectiveness of the technology is proved.
-
Date submitted2018-01-01
-
Date accepted2018-03-24
-
Date published2018-06-22
Complex petrophysical correction in the adaptation of geological hydrodynamic models (on the example of Visean pool of Gondyrev oil field)
- Authors:
- V. A. Repina
- V. I. Galkin
- S. V. Galkin
The authors review a method of combined porosity and volume density correction in the process of modeling the distribution of reservoir permeability. Basing on petrophysical investigations of core samples from Bashkir fold deposits, an association between rock porosity, density and permeability has been analyzed. Significant correlation has been observed for the above mentioned parameters in porous collectors in contrast to reduced correlation for dense rocks and intervals of anomalously high poroperm characteristics. For terrigene porous collectors the authors propose a model of permeability assessment based on combined porosity and density correction. A modified model was developed for Visean pool of Gondyrev oil field, where collector permeability had been calculated as a function of rock porosity and density. The modified model has been compared to the conventional one; significant differences have been detected. In the modified version maximum permeability is associated with the southern part of the pool, whereas the conventional method points out the central part and predicts lowering permeability closer to the periphery. Geological model in the modified version is more homogenous than the conventional one and has no sharp peaks and valleys. The calculations have been made that reproduce the history of field development for both permeability volumes. Authors demonstrate that total oil production obtained using the modified model has a much better correlation with the actual data. The best results from using suggested method apply to the initial stage of development due to better convergence of high-rate wells. On the whole, comparison of two methods shows that for the purposes of production history adaptation the modified model is significantly better than the conventional one. Hence, the method of density correction allows for better justification of differences in the lithology of Visean collectors, which ultimately results in higher accuracy of data on residual oil reserves in the deposit.
-
Date submitted2016-11-21
-
Date accepted2017-01-23
-
Date published2017-04-14
Prospects of obtaining samples of bottom sediments from subglacial lake Vostok
- Authors:
- N. I. Vasilev
- G. L. Leichenkov
- E. A. Zagrivnyi
The paper proves the timeliness of obtaining and examining bottom sediments from subglacial Lake Vostok. Predictive geological section of Lake Vostok and information value of bottom sediments have been examined. Severe requirements towards environmental security of lake examinations and sampling of bottom sediments rule out the use of conventional drilling technologies, as they would pollute the lake with injection liquid from the borehole. In order to carry out sampling of bottom sediments from the subglacial lake, it is proposed to use a dynamically balanced tool string, which enables rotary drilling without any external support on borehole walls to transmit counter torque. A theoretical analysis has been carried out to assess the operation of the tool string, which is a two-mass oscillatory electromechanical system of reciprocating and rotating motion (RRM) with two degrees of freedom.
-
Date submitted2015-10-21
-
Date accepted2015-12-16
-
Date published2016-08-22
Flow instability in producing well at flash-steam fields
- Authors:
- A. N. Shulyupin
Theoretical foundations are presented for forecasting operation instability of producing wells at flash-steam fields. The considered topic gains actuality because of the new conditions for developing geothermal power industry which call for solicitous use of the wells fund. Instability mechanism is considered: increased discharge results in the growth of the force generating the flow, which in turn results in still higher discharge. The force grows due to weakening of gravitational component which counteracts the flow in the result of depletion in the density of flash-steam mixture. It is demonstrated that due to the specifics of development of such instability in a geothermal well the reaction of well foot pressure to change in the discharge cannot influence the stability in any effective way, while the reaction of wellhead pressure may work as a stabilizing factor. Principal weaknesses are pointed out of former ideas on flow instability in flash-steam wells. The condition of stable flow should be the positive value of the derivative on discharge of the internal well foot pressure defined as the sum of wellhead and internal pressure drop.
-
Date submitted2015-08-21
-
Date accepted2015-10-24
-
Date published2016-04-22
Results of the 5G borehole drilling at russian antarctic station «Vostok» and researches of ice cores
- Authors:
- N. I. Vasilev
- A. N. Dmitriev
- V. Ya. Lipenkov
We produce an information about results and features of the 5G borehole drilling in Antarctic layer at Russian station Vostok. Main regularities of the change structured and physical properties by Antarctic ice layer depth, which determine mechanical and reological properties if ice, which influence to sinking of a borehole and to the maintaining of it in a working condition, the safe and competitive technologies creation for drilling of strong ice layers and the environmentally safe technology of the subglacial reservoirs unsealing. We also produce results of the ice cores researching and the paleoclimatic raws construction, which are reconstructed by the ice cores researching from Vostok station, which is compared with isotopic graph. This graph describes changes of World ocean level.
-
Date submitted2014-11-04
-
Date accepted2015-01-20
-
Date published2015-10-26
Stability of productive well operation in a steam hydrothermal field
- Authors:
- A. N. Shulyupin
A condition of well operation stability based on agreement of indicator characteristics of well and aquifer throughput capacity is considered. Two hypotheses of the stability state are examined: with one and two possible combinations of characteristics. It is shown that taking into account resistance between the wellhead and the environment with constant pressure helps explain all the features of wellhead pressure and flow-rate relationship of steam-water wells based on the hypothesis with one combination (when the operating point is located on the ascending branch of a well characteristic). The throttling effect on the wellhead which was used in the development of the Mutnovka steam hydrothermal field in order to stabilize the well operation is explained.
-
Date submitted2014-06-24
-
Date accepted2014-08-31
-
Date published2014-12-22
Unique engineering and technology for drilling boreholes in Antarctic ice
- Authors:
- Vladimir S. Litvinenko
As the result of many years of research into the processes of the transfer of ice as a rock mass on a global scale, concerning the Antarctic ice sheet at the ultra-deep 5G borehole, a discovery has been made that is of international significance in the areas of glaciology and geodynamics. Those who created the theory of thermal and mechanical penetration into ice and loose sediments have developed unique technology and engineering processes in order to drill boreholes using thermal and mechanical methods.
-
Date submitted2009-09-16
-
Date accepted2009-11-15
-
Date published2010-06-25
Directional drilling in ice caps
Directional drilling technology can be used in glacier boreholes to obtain additional ice cores and to pass over sticking drills. Experimental sidetracking of 5G-2 hole in the deep borehole at Vostok station, Antarctica, showed the high efficiency of the directional drilling without using of special whip-stocks to deviate the hole.