-
Date submitted2022-05-17
-
Date accepted2022-09-06
-
Date published2022-11-03
On the need to classify rock mass fed to dry magnetic separation
The hypothesis of a possible use of dry magnetic separation is substantiated on the example of ores from ferruginous quartzite deposits operated by plants of PAO “Severstal” Holding. Size class of ore after medium crushing is –80+0 mm when the vibrating feeder is used for feeding ore mass to the separation zone. The rationale is based on the analysis of video recording of physical simulation on a laboratory drum magnetic separator of SMBS-L series, in the VSDC Video Editor, and simulation modelling of dry magnetic separation on its virtual prototype in Rocky DEM software package. It has been proved that the use of a vibrating feeder for feeding the material to the working area of a magnetic separator makes it possible to: form a monolayer on the surface of the vibrating feeder chute with a thickness close to the maximum size of a lump of separated ore; implement batch feed of material to the separation zone; increase the spacing between lumps in the separation zone when passing through the free fall area, thereby allowing dry magnetic separation of ferruginous quartzites of size class –80+0 mm without pre-preparation.
-
Date submitted2021-11-17
-
Date accepted2022-04-06
-
Date published2022-11-10
Method for predicting the stress state of the lining of underground structures of quasi-rectangular and arched forms
- Authors:
- Maksim A. Karasev
- Tien Tai Nguyen
A method for predicting the stress-strain state of the lining of underground structures, the shape of the cross-section of which is different from the circular outline, is considered. The main task of the study is to develop a methodology for assessing the influence of the parameters of the cross-section shape of underground structures on the stress state of the lining. To solve this problem, a method for calculating the stress state of the lining for arched tunnels with a reverse arch and quasi-rectangular forms is substantiated and developed. The methodology was tested, which showed that the accuracy of the prediction of the stress state of the lining is sufficient to perform practical calculations. An algorithm for multivariate analysis of the influence of the cross-sectional shape of underground structures of arched and quasi-rectangular shapes on the stress state of the lining is proposed. Parametric calculations were performed using the developed algorithm and regularities of the formation of the stress state of the lining of underground structures for various engineering and geological conditions, as well as the initial stress state field, were obtained. A quantitative assessment of the influence of geometric parameters of tunnels on their stress-strain state was performed.
-
Date submitted2021-10-14
-
Date accepted2022-04-07
-
Date published2022-04-29
The influence of the shape and size of dust fractions on their distribution and accumulation in mine workings when changing the structure of air flow
The results of the analysis of statistical data on accidents at Russian mines caused by explosions in the workings space have shown that explosions of methane-dust-air mixtures at underground coal mines are the most severe accidents in terms of consequences. A detailed analysis of literature sources showed that in the total number of explosions prevails total share of hybrid mixtures, i.e. with the simultaneous participation of gas (methane) and coal dust, as well as explosions with the possible or partial involvement of coal dust. The main causes contributing to the occurrence and development of dust-air mixture explosions, including irregular monitoring of by mine engineers and technicians of the schedule of dust explosion protective measures; unreliable assessment of the dust situation, etc., are given. The main problem in this case was the difficulty of determining the location and volume of dust deposition zones in not extinguished and difficult to access for instrumental control workings. Determination of the class-shape of coal dust particles is a necessary condition for constructing a model of the dust situation reflecting the aerosol distribution in the workings space. The morphological composition of coal mine dust fractions with dispersion less than 0.1 has been studied. Particle studies conducted using an LEICA DM 4000 optical microscope and IMAGE SCOPE M software made it possible to establish the different class-shapes of dust particles found in operating mines. It was found that the coal dust particles presented in the samples correspond to the parallelepiped shape to the greatest extent. The mathematical model based on the specialized ANSYS FLUENT complex, in which this class-form is incorporated, is used for predicting the distribution of explosive and combustible coal dust in the workings space. The use of the obtained model in production conditions will allow to determine the possible places of dust deposition and to develop measures to prevent the transition of coal dust from the aerogel state to the aerosol state and thereby prevent the formation of an explosive dust-air mixture.
-
Date submitted2020-06-02
-
Date accepted2021-05-21
-
Date published2021-09-20
Analysis of technological schemes for creating a geodetic control at the industrial site
The article highlights the issues of creating with the necessary accuracy a planned control on the industrial site of the engineering structures under construction using satellite technologies and total stations. Depending on the design features of the engineering structures under construction, as well as the technological scheme for the installation of building constructions and industrial equipment, various schemes for creating such control are considered, based on the application of the inverse linear-angular notch. Errors in the source data are one of the main errors that affect the accuracy of geodetic constructions, including the solution of the inverse linear-angular notch. When creating a geodetic network in several stages, the errors of the initial data of the first stage affect the values of the root-mean-square errors (RMS) of determining the position of the second stage points, the errors of which affect the value of the RMS of the position of the third stage points, etc. The reason for their occurrence is the errors of geodetic measurements that occur at each stage of control creating, as well as the stability violation of the points during the production of excavation, construction and installation works. When determining the coordinates of a separate project point at the stage of its removal in-situ by a total station, the entire network is not equalized in the vast majority of cases, and the coordinates of the starting points to which the total station is oriented are considered error-free. As a result, the RMS determination of the points coordinates of the control network or the removal of the design points of the elements of building structures and equipment will also be considered satisfying the requirements, i.e. the measurement accuracy will be artificially overestimated and will not correspond to the actual one obtained. This is due to the fact that the accumulation of errors in the initial data is not taken into account when the number of steps (stages) of control creating increases. The purpose of this work is to analyze the influence of measurement errors and initial data when creating a geodetic control on an industrial site by several stages of its construction based on inverse linear-angular notches and a priori estimation of the accuracy of the determined points position.
-
Date submitted2020-06-16
-
Date accepted2021-03-29
-
Date published2021-09-20
Empirical regularities investigation of rock mass discharge by explosion on the free surface of a pit bench
- Authors:
- Igor A. Alenichev
- Ruslan A. Rakhmanov
Minimizing the discharge of blasted rock mass into the developed space of the pit is a very relevant area for study, as it allows to increase the processability of work and reduce the cost of mining. The article presents the results of experimental industrial explosions, during which the study of this issue was conducted. The main purpose of the work was to establish the key factors affecting the volume of rock mass discharge to the pit haulage berm. During the analysis of the world experience of research on this topic, the key factors affecting the formation of collapse and discharge – natural and technological – are identified. The method of conducting experiments and collecting data for analyzing the influence of technological parameters of location, charging and initiation of wells on the volume of rock mass discharge is described. It is established that the main discharge to the pit haulage berm is formed by the volume of rock mass limited by the prism of the slope angle. With a sufficient rock mass displacement from the edge of the bench crest towards the center of the block, only the wells of the 1st and 2nd rows participate in the discharge formation. Empirical dependences of the total volume of rock mass discharge on the length of the block along the bench crest, the specific consumption of explosives, the size of a rock piece P 50 and the rate of rock breaking are obtained. The obtained results can be used to design the parameters of the drilling and blasting operations (DBO), as well as to predict and evaluate the possible consequences of a mass explosion in similar mining and geological conditions.
-
Date submitted2020-11-20
-
Date accepted2021-03-30
-
Date published2021-06-24
Regularities of changing the dimensions of the main bore of the cylinder of TMZ-450D diesel engine during the technological process
The article deals with the problems arising during the mechanical and thermal treatment of the TMZ-450D diesel engine cylinder, which is the base part of the engines of small-sized generators and compressors, which are widely used for mobile units in the oil and gas and mining industries. It was found that the metal in the casting has a non-uniform structure, the density of which ranges from 6.75 to 7.25 g/cm 3 . Redistribution of dislocations and residual stresses in the casting leads to significant changes in the size and shape of the main bore. In addition to the successive changes in size specified by the technology due to the removal of the designated allowance, the dimensions and shape change arbitrarily, uncontrollably in the course of the technological process. It is shown that artificial aging by a thermal method does not provide the desired dimensional stability; therefore, it is proposed to supplement it with natural aging after rough boring for six months. It was revealed that the use of morally and physically outdated equipment makes it necessary to increase the number of finishing operations of honing and, accordingly, to increase the labor intensity of cylinder manufacturing. The use of a two-position boring machine is substantiated, on which the transitions of semi-finishing and fine boring are combined. This completely eliminates the copying of errors that arose when changing the base on previous operations. The use of a two-position modular boring machine ARS-4/Ts of increased accuracy and rigidity significantly increases the accuracy of the bore hole, which makes it possible to reduce the number of honing operations. A variant of the technological process of mechanical and heat treatment is proposed, including natural aging, the use of double boring on a modular boring machine, which will reduce the number of honing operations to one, including rough and finish transitions.
-
Date submitted2020-05-16
-
Date accepted2020-07-30
-
Date published2020-12-29
Results of the study of kinetic parameters of spontaneous combustion of coal dust
The article is devoted to the study of the problem of spontaneous combustion of energy grades of coal not only during storage, but also during transportation. As the main samples for the study, the energy grades of SS and Zh coals were selected. The main task of the scientific research was to study the rate of cooling and heating of coal depending on their thermophysical parameters and environmental parameters. To solve this problem, the authors used both the author's installations designed to study the thermophysical parameters of the spontaneous combustion process (the Ya.S.Kiselev method), and the NETZSCH STA 449 F3 Jupiter synchronous thermal analysis device, the NETZSCH Proteus Termal Analysis software package. On the basis of a complex study of the spontaneous combustion process, the authors of the article obtained the kinetic characteristics of the spontaneous heating process (activation energy and pre-exponential multiplier). Nomograms of the permissible size of coal density of different types and shapes of accumulation depending on the ambient temperature are presented, practical recommendations for the prevention (avoidance) of spontaneous combustion of coal fuel are given.
-
Date submitted2019-06-27
-
Date accepted2019-09-07
-
Date published2019-12-24
Optimization of geometrical parameters of the hydro-cyclone inertial Venturi separator
- Authors:
- V. N. Makarov
- A. V. Ugolnikov
- N. V. Makarov
The usage of nanosized particles as modifying agents opens new possibilities in the creation of materials with unique properties. The effective qualitative improvement of Russia's GDP structure is based on the recycling of technogenic mineral formations (TMF) and the production of high-tech products. Numerous studies have shown that the efficiency of this process is limited by high requirements to the fractional composition, median size, and dispersion of TMF particles, as well as imperfection of equipment and technology and their classification. The strict classification requirements must be taken into account, when developing separation methods for the dispersion of the median sizes of TMF microparticles under the conditions of the probabilistic distribution of the physical and mechanical parameters of the feed. The studies covered in the article are based on the provision on a significantly greater influence of inertial forces on the trajectory of a hydrodynamically unsteady motion of the dispersed «a microparticle – a drop of liquid» system during the hydro-cyclone separation with respect to the aerodynamic forces of their movement in a fluidized bed. The paper shows that within the range of kinetic energy of the translational motion of liquid droplets, which overcomes the aerodynamic barrier of coagulation of hydrophobic TMF particles, the minimum diameter of absorbed microparticles during hydro-cyclone coagulation depends only on the magnitude of the angular velocity of rotation of the liquid droplets. We obtained the equations for the Euler and Reynolds criteria, their average values, and the relaxation time of liquid droplets with integrated micro and nanoparticles of TMF, depending on their median size during hydro-cyclone separation. The developed mathematical model of inertial hydro-cyclone separation of finely dispersed TMF allows determining the optimal geometric parameters and energy characteristics of the Venturi separator, its aerator, and the position of the receiving tanks. The experimental results confirmed the possibility of classifying finely dispersed wastes of mining and metallurgical production in the range of median sizes (0.5-5)∙10 –6 m by fractions with a dispersion of not more than 20 %.
-
Date submitted2018-09-08
-
Date accepted2018-10-27
-
Date published2019-02-22
Special strategy of treatment of difficulty-profile conical screw surfaces of single-screw compressors working bodies
- Authors:
- A. S. Vasilev
- A. A. Goncharov
The article deals with the problems arising during the shaping of complex profile tapered helical surfaces. These surfaces form the geometry of the working bodies of single-screw miniature compressors, which have great prospects for use in mobile miniature compressor plants, which is especially important for medical and space technology, robotics, oil and gas and mining industries. Due to the fact that the capabilities of existing CAD systems do not allow obtaining three-dimensional models of these surfaces, the problem of preparing a control program for a CNC machine arises, since the calculation of the tool path in CAM systems when processing complex surfaces is impossible without a three-dimensional surface model. To solve the problem, an automated programming system was developed that implements a formalized toolpath calculation in accordance with the proposed special processing strategy for conical helical surfaces. As the initial data for calculating the toolpath, the system needs information about the tool geometry and the helical surface in a parametric form, which makes it possible to abandon the construction of a three-dimensional surface model. The results of processing prototypes for the proposed strategy are given.
-
Date submitted2018-04-26
-
Date accepted2018-06-28
-
Date published2018-10-24
Modern specificity of corporate relations on the example of vertical-integrated company
- Authors:
- A. A. Lapinskas
The article describes features of the modern model of Russian corporate relations on the example of a vertically integrated and diversified company. The CRs are still affected by the consequences of the privatization processes of state and municipal enterprises in the 1990s, which resulted in the emergence of a peculiar economic model of oligarchic capitalism and a specific model of CR. On a specific example, the pros and cons of this model are analyzed considering the processes of consolidation of entrepreneurial activities in the metallurgy and gold mining industry. The conclusion is made about the predominance of quasi-corporate relations, the ways to improve CR are suggested.
-
Date submitted2010-07-06
-
Date accepted2010-09-06
-
Date published2011-03-21
Distribution of products of destruction of granite files
The article considers the problem of size distribution of grain-size composition of the blasted rock mass, rock fragments blasted rock mass and rock blockiness. The logarithmic-normal distribution law is laid down for all blasted granite mass products. It was proved, that logarithmic variance of logarithmic normal distribution law of the fractured rock mass fragments’ distribution is a structural invariant on the level of statistical universe of the block and fragments.
-
Date submitted2008-10-17
-
Date accepted2008-12-07
-
Date published2009-12-11
Morphometry of aggregates and modeling of phase transition kinetics under metamorphism
- Authors:
- Yu. L. Gulbin
The paper discusses some general relations between the structure of metamorphic rocks and mechanisms of phase reactions. Among these relations is the influence of nucleation and growth of kinetics on the crystal size distribution. A brief overview is made of theoretical models which have been proposed to explain granulometric properties of rocks, and kinetic laws and factors on the metamorphic crystallization are considered by the example of metapelitic garnets, including the phenomenon of avalanche nucleation at finite overheating as well as the growth of porphyroblasts under diffusion-limited conditions. As a result, a new approach to modeling of native granulometric curves is presented.