-
Date submitted2023-12-07
-
Date accepted2024-11-07
-
Date published2025-04-25
Determination of the tangential component of cutting resistance during frozen sedimentary rock cutting using blocked, deeply blocked and cell cutting methods
Due to the insufficient accuracy of existing studies of frozen sedimentary rock cutting process for practical calculations, the article solves the problem of determining the tangential component cutting resistance for blocked, deep blocked and cell cutting, which are currently the most commonly used methods in earthmoving equipment. The cutting tool and rock mass force interaction is considered from the point of view of the emerging stresses, which act on the separated chip element. The analytical dependences for determining the tangential component of cutting resistance were obtained. The numerical explanation of the choice of cell cutting in relation to blocked and deeply blocked cutting is given. For all three methods of cutting, under equal geometrical parameters of the cutting tool and the physical and mechanical properties of the frozen rock, the numerical value of the tangential component of cutting resistance is obtained. The comparison of the cutting resistance estimated values has shown that cell cutting requires relatively less energy and is preferred during the process of frozen sedimentary rock excavation. During field and laboratory investigations with the use of a multi-purpose cutting stand, a sufficient convergence of the analytical statements with the physics of frozen sedimentary rock cutting process was established. The results of the research allow a more reasonable approach to the adjustment of existing methods for determining the required tractive force and power for the drive of an excavation machine, and, therefore, to the actual efficiency and profitability of work.
-
Date submitted2023-10-31
-
Date accepted2024-11-07
-
Date published2025-01-24
Specifics of magnetotelluric studies in Antarctica
One of the priority areas of scientific research in Antarctica is the study of its deep structure. Most of the continent is covered with a thick ice sheet, so the main geoscientific data are acquired using geophysical methods, among which magnetotelluric (MT) ones have the greatest penetration depth and insignificant environmental impact. The possibility of acquiring high-quality MT data in the conditions of the sixth continent has long been questioned. The work is aimed at studying the specifics of magnetotelluric survey in Antarctica. The following tasks were set: to summarize the world experience of studying Antarctica using MT sounding methods; to identify factors that negatively affect the high-quality data acquisition; to determine methods for minimizing the influence of these factors. The article analyses geophysical studies conducted by the magnetotelluric sounding method in the Antarctic region from 1964 to the present. The application of the method is complicated by the following: extremely low temperature affects the drop in the batteries capacity, freezing of the non-polarizing electrodes solution, and changes in the strength properties of materials. Electromagnetic noise occurs during strong winds; proximity to the magnetotelluric field source can violate the plane wave principle on which the method is based. The ice sheet covering most of Antarctica does not allow acquiring optimal values of the contact resistance of the electrode grounding; the extended coastline distorts the acquired data. Studies of the influence of factors complicating the MT sounding method in the coastal and central parts of Antarctica made it possible to formulate recommendations for preparing equipment and adapting the work procedure, modifying the processing flow and a set of measures to ensure safety, the implementation of which will both allow safe performance of geophysical investigations and high-quality data acquisition.
-
Date submitted2022-07-10
-
Date accepted2023-06-20
-
Date published2024-02-29
Mathematical modeling of the electric field of an in-line diagnostic probe of a cathode-polarized pipeline
A mathematical model of the in-line control of the insulation resistance state for cathodically polarized main pipelines according to electrometry data is considered. The relevance of the work is caused by the opportunity to create in-line internal isolation defects indicators of the main pipelines for transported liquids that are good conductors and expand the functionality of monitoring and controlling cathodic protection systems of the main pipelines. Features of the mathematical model are: consideration of the electric conductivity of transported liquid influence on electric field distribution; consideration of the influence of external and internal insulating coating resistance; use of the electric field of an in-line diagnostic probe for quality control of internal insulation. Practical significance consists in the development of modeling methods for control subsystems of main pipeline protection against corrosion and the development of special mathematical and algorithmic support systems for monitoring and controlling the operating modes of the cathodic protection station of main pipelines.
-
Date submitted2022-10-26
-
Date accepted2023-02-13
-
Date published2023-07-19
Determination of the grid impedance in power consumption modes with harmonics
The paper investigates the harmonic impedance determination of the power supply system of a mining enterprise. This parameter is important when calculating modes with voltage distortions, since the determined parameters of harmonic currents and voltages significantly depend on its value, which allow the most accurate modeling of processes in the presence of distortions in voltage and current. The power supply system of subsurface mining is considered, which is characterized by a significant branching of the electrical network and the presence of powerful nonlinear loads leading to a decrease in the power quality at a production site. The modernization of the mining process, the integration of automated electrical drive systems, renewable energy sources, energy-saving technologies lead to an increase in the energy efficiency of production, but also to a decrease in the power quality, in particular, to an increase in the level of voltage harmonics. The problem of determining the grid harmonic impedance is solved in order to improve the quality of design and operation of power supply systems for mining enterprises, taking into account the peculiarities of their workload in the extraction of solid minerals by underground method. The paper considers the possibility of determining the grid impedance based on the measurement of non-characteristic harmonics generated by a special nonlinear load. A thyristor power controller based on phase regulation of the output voltage is considered as such a load. Simulation computer modeling and experimental studies on a laboratory test bench are used to confirm the proposed method. The recommendations for selecting load parameters and measuring device connection nodes have been developed.
-
Date submitted2022-01-21
-
Date accepted2022-11-14
-
Date published2023-08-28
Strategy of mine ventilation control in optimal mode using fuzzy logic controllers
- Authors:
- Aleksei V. Kashnikov
- Yuri V. Kruglov
The issues related to improving the efficiency of automatic ventilation control systems of mines that regulate the air supply to the mine in accordance with the need are considered. During the tests of such a system in the 3RU mine of OAO Belaruskali, the shortcomings of its existing, implementation, associated with the incorrect choice of the most difficult-to-ventilate direction, were revealed. The possibilities of implementing a control strategy, in which the system automatically determines the optimal configuration of the operating modes of fans and regulators, are demonstrated. As an alternative to the implemented algorithms, it is proposed to use a fuzzy control device to account for the nonlinearity of the dependence of the input and output parameters of ventilation equipment and to set the conditions for the optimal operating mode of the system in a declarative form. To assess the effectiveness of the proposed approach, the data of simulation modeling of the current ventilation mode and the transition from one ventilation mode to another are analyzed with comparison with the actual data of the system operation. The simulation results show that the use of an upgraded control scheme for the main ventilation fan based on fuzzy logic in the implementation of automatic ventilation control systems makes it possible to eliminate the possibility of a shortage of fresh air in the regulated directions of its movement, as well as excessive power consumption of the main ventilation fan.
-
Date submitted2021-03-05
-
Date accepted2021-10-18
-
Date published2021-12-16
Physical and mathematical model of rock destruction by a milling machine cutter
As a result of the analysis of the work on rock destruction by cutters of milling of machines, it was found that the existing developments do not allow us to proceed to the derivation of calculation d dependencies for determining fracture resistance, or can be used only in preliminary calculations of the known by design parameters of milling machines. To eliminate these disadvantages, a combined physical and mathematical model of the process of interaction of a single milling cutter with a spherical tip with the rock has been developed. Consideration of the physical picture of the action of forces and stresses acting from the cutter with spherical tips on the separating rock element in the limiting condition allowed to describe analytically the components of total resistance, which are the mathematical part of the physical and mathematical model of rock destruction by cutters. Analytical dependences for determining the tangential and normal components of fracture resistance of rocks of medium hardness have been obtained. The adequacy of the physical and mathematical model to the physical process of destruction of rocks of different hardness by cutters on a universal stand was tested both in the field and in the laboratory conditions. Technical evaluation of the results of experimental studies confirms the reliability of the developed physical and mathematical model.
-
Date submitted2017-11-15
-
Date accepted2018-01-13
-
Date published2018-04-24
Use of nano-dimensional hydrophobic coatings for obtaining electrets based on silicon dioxide
- Authors:
- N. S. Pshchelko
The article considers the physical-technological foundations of formation of the silicon dioxide (SiO 2 ) based electret for use in devices of MEMS technology. Studies have shown that the best electret properties are in SiO 2 obtained in «wet» oxygen medium as compared to samples obtained by other oxidation methods. This is probably due to the large number of Si-OH groups on the surface of the oxide in the «wet» SiO 2 , which increases the effectiveness of the hydrophobic coatings during the modification of the SiO 2 surface. It has been found that other methods of obtaining oxide, for example, electrochemical or plasmachemical, do not make it possible to obtain SiO 2 with good electret properties. The decrease of the charge injected into an electret can occur due to the presence of volume or surface conductivity, as well as the screening of this charge by opposite charges from the medium, leading to significant decrease of electret surface potential at high ambient humidity. To increase the stability of the electret effect, it is necessary to perform water-repellency treatment of SiO 2 surface by applying thin (nanosized) water-repellent coatings. Experimental results on the stability of the electret surface potential are presented for usage of various water repellents. The most promising water repellents are high-temperature photoresist FPT-1-40 and polyimide nanolayer compositions – Langmuir-Blodgett films.
-
Date submitted2017-11-22
-
Date accepted2018-01-04
-
Date published2018-04-24
Justification of a methodical approach of aerologic evaluation of methane hazard in development workings at mines of Vietnam
- Authors:
- V. V. Smirnyakov
- Nguen Min' Fen
The methods of evaluation of the aerological conditions to be performed for the purpose of normalization of mining conditions are provided in the present review; the location of possible accumulations of explosive gases during the drift of the development workings are taken into account. To increase the safety of the development working regarding the gas factor, a complex evaluation of a working was developed with respect to the dynamics of methane emission and air coursing along the working which is strongly affected by the character of the leakages from the ventilation ducting. Thereby, there occurs a necessity of the enhancement of a methodical approach of calculation of ventilation of a working which consists in taking into consideration a total aerodynamic resistance of the booster fan including the local resistances of the zones of the working. An integer simulation of the gas-air flows realized on the basis of a software package FLowVision allows to evaluate a change in the methane concentration in the zones of local accumulations.
-
Date submitted2017-09-17
-
Date accepted2017-11-06
-
Date published2018-02-22
Collaborative interpretation of the data obtained by resistivity and ground penetrating radar methods for assessing the permeability of sandy clay soils
- Authors:
- D. A. Lalomov
- V. V. Glazunov
A method for estimating the filtration factor of sandy clay soils is considered on the basis of a joint interpretation of the data of a set of methods of engineering electrical exploration, including electrical resistivity tomography and ground penetrating radar studies. The solution of this problem is based on the use of known empirical connections between the imaginary and real parts of the complex dielectric permittivity, specific electrical resistance, and Q factor. An example of the effective joint use of the ground penetrating radar and non-contact electrical resistivity tomography shows how to obtain qualitative and quantitative estimates of a changing filtration factor in a draining road layer. It is necessary to use precise engineering geological information in order to provide the required estimates. The proposed approach makes it possible to describe continuous profiles of a pavement and underlying layers by ground penetrating radar and electrical resistivity tomography, as well as to assess soil properties when conducting an electrical survey from the surface of asphalt concrete pavement. Recommendations for the implementation of the developed methods of complex engineering and geophysical research are given for solving issues of repair work design, supervision, and quality control of road construction.
-
Date submitted2016-11-18
-
Date accepted2016-12-28
-
Date published2017-04-14
Frequency electromagnetic sounding with industrial power lines on Karelia-Kola geotraverse
The paper describes theory, method and first experimental results of research on the interaction between electromagnetic waves of extremely low and ultra low frequency (0.1-200 Hz), the Earth crust and ionosphere in the field of two mutually orthogonal industrial power lines, 109 and 120 km long, in the course of FENICS experiment (Fennoscandian Electrical conductivity from Natural and Induction Control Source soundings). The main focus was on the observation results along the line of Karelia-Kola geotraverse over a distance of 700 km from the source. High horizontal homogeneity of geoelectrical lithosphere section has been detected in the eastern part of the Baltic shield at depth range from 10-15 to 50-70 km. Parameters of «regular» lithosphere section have been specified to the depth of 60-70 km. As a result of inverse problem solution for the western part of Karelia and Central Finland, a zone of decreased transverse resistivity has been detected at the depth of 50-60 km, corresponding to the area, detected by seismic methods, where Moho boundary reaches the same depth.
-
Date submitted2015-08-18
-
Date accepted2015-10-09
-
Date published2016-04-22
Analysis of charge space distribution influence on electric adhesion forces
- Authors:
- N. S. Pshchelko
Modeling ideas of physical and chemical processes when using an anodic bonding for materials connection are developed. The kinetics of a charge accumulation in an electrode region in a dielectric is considered. The thickness of a charge layer, electric fields strength and value of the ponderomotive pressure providing connection of materials are calculated. It is shown that the necessary ponderomotive pressure resulting in a dielectric-to-conductor seal is normally about ten megapascal and the time required is about ten minutes. The appearance of great pulling electric fields at anodic bonding process with a conductor surface to dielectric turns out to be possible due to the interlayer polarization developing in dielectric under the action of electric voltage. This results in a negative charge accumulation in a layer of small thickness beside anode. Thus applied electric voltage is distributed not through the whole thickness of a dielectric, but in fact is applied to a narrow area of the three-dimensional charge be-side anode. Arising strong electric fields force the connected materials to unite. The physical and mathematical models for force characteristics of non-uniform electric field are developed. Dependences of parameters of anodic bonding junction on time are considered. The expressions allowing to choose well-founded time of formation of anodic bonding junction are obtained, intensity of electrostatic fields and forces in dynamics is calculated. Research of a charge intermittence influence on electrostatic field strength has shown a considerable differences on small distances to the charged surface between carried out and traditional ways of calculation.
-
Date submitted2010-07-10
-
Date accepted2010-09-04
-
Date published2011-03-21
Experimental research of the train aerodynamic resistance
- Authors:
- V. A. Pleskunov
In paper the technique of definition of aerodynamic resistance of the train, a being main component of a piston pressure is resulted. The urgency of the given theme is caused by essential influence of a piston pressure on distribution of fresh air on a tunnel and accordingly on safe operation of railway tunnels.
-
Date submitted2009-09-08
-
Date accepted2009-11-18
-
Date published2010-06-25
Anodic bonding method for adhesion enhancement of conducting films to dielectric substrates
- Authors:
- A. G. Syrkov
- N. S. Pshchelko
The appearance of great pulling electric fields at anodic bonding process with a conductor surface to ionic dielectric turns out to be possible due to the interlayer polarization developing in dielectric under the action of electric voltage. This results in a negative charge accumulation in a layer of small thickness beside anode. Thus applied electric voltage is distributed not through the whole thickness of a dielectric, but in fact is applied to a narrow area of the three-dimensional charge beside anode. Arising strong electric fields force the connected materials to unite. In the present work it is shown that use of the discussed technology allows to increase considerably adhesion of conducting films to dielectric substrates both in the process of their deposition and after it.
-
Date submitted2009-08-25
-
Date accepted2009-10-24
-
Date published2010-02-01
Using of electric field for manufacturing and nondestructive testing of a capacitor sensors and actuators
- Authors:
- N. S. Pshchelko
- V. V. Buevich
Some designs of capacitor sensors and actuators which work is based on electric field use are considered. It is shown that these designs are rather cheap in manufacturing, but thus possess good technical characteristics. The theoretical substantiation of possibility of electrostatic forces use for balancing of a pressure difference in the corresponding measuring device is adduced. Procedure for definition of parameters of a condenser structure cap is considered. The procedure allows by means of one operation – volt-capacitance characteristic measuring – to define the whole complex of the major parameters of a cap-size of a working air gap, a membrane deflection, surface electret potential and a membrane tension. Analytical expression for capacitance of a cap depending on the specified parameters and measuring of its volt-capacitance characteristic allow to define these parameters by solving corresponding system of equations. The procedure considered in the present work is a method of a not-destroying control.
-
Date submitted2009-08-23
-
Date accepted2009-10-17
-
Date published2010-02-01
Mathematical description of microwave contact level controller for liquid agent
- Authors:
- N. V. Teterin
- O. M. Bolshunova
It is shown the problem of measurement of level in oil tanks. Considered the use of a method of the sway electromagnetic radiation for the control of level of section of environments in tanks, made its mathematical description, resulted the estimation of results of practical application.
-
Date submitted2008-10-04
-
Date accepted2008-12-13
-
Date published2009-12-11
1D-interpretation technology of airborne tem data
- Authors:
- A. V. Chernyshev
One-dimensional interpretation methods of airborne transient electromagnetic data are considered. Main techniques, used for adaptation of standard methods of ground electroprospecting data interpretation to airborne technique, are described. The efficiency of methods examined was analyzed on theoretical data set. An example of practical application of methods developed is presented.
-
Date submitted2008-10-23
-
Date accepted2008-12-05
-
Date published2009-12-11
Application of electrical prospecting in combination with seismic prospecting for the geological section prediction and search of hydrocarbon deposits
- Authors:
- V. A. Kuzin
- A. A. Korukhova
The possibility of application of electrical prospecting method SGN (sounding by field growing in the near-field zone) in combination with CDP seismic prospecting for sedimentary section investigations and hydrocarbon deposits prospecting is considered. The physical basis of the method application for hydrocarbon prospecting is the effect of higher resistance of seams, saturated by hydrocarbons. The effect is reflected in the curve of electromagnetic field growth ε(t). The procedures of field works, processing and interpretation of electrical prospecting data are presented.
-
Date submitted2008-10-15
-
Date accepted2008-12-17
-
Date published2009-12-11
Low frequency inductive airborne electromagnetic system em-4h
Nearly all existing airborne EM-survey systems have been tested in Russian Federation. And for today the most popular EM-system is the frequency-domain one, called EM-4H. The article gives the description of the EM-4H system, that have been developed by «Geotechnologies» JS. This instrument allows effective conductivity mapping on a 1:25000 scale. It provides performing of 100 kilometers of survey per hour on the average.
-
Date submitted1951-07-18
-
Date accepted1951-09-27
-
Date published1952-12-23
Asymmetric bending of annular plate by moment
- Authors:
- L. S. Burshtein
Asymmetric bending of the ring plate is encountered when developing designs of couplings, compensators and various corrugated elements included in the overall system to increase its elasticity. The efficiency of such plates is determined not only by their dimensions (internal and external diameters, wall thickness), but also depends to a large extent on the rigidity of the elements to which they are directly adjacent and the design of the transition from the plate to the element conjugated with it. In some cases, the method of fixing the plate along the outer contour comes closest to rigid embedment, in others it can be considered equivalent to hinged support. The main value characterizing the elasticity of the plate is the angle of rotation of the inner contour to which the external bending moment is applied. This value for the scheme with hinged support, all other things being equal, is significantly greater than for the scheme with rigid embedment. However, along with this, there is an unfavorable factor associated with a significant increase in stresses in the scheme with hinged support compared to rigid embedment. The correct solution to the problem comes down to selecting the dimensions of the elastic element in such a way as to obtain the largest angle of rotation of the internal contour at stresses not exceeding the permissible ones. For this purpose, it would be necessary to take into account the degree of rigidity of the fastening and make the calculation as for the scheme with elastic fixing.