-
Date submitted2023-09-05
-
Date accepted2024-11-07
-
Date published2025-02-25
Investigation of the accuracy of constructing digital elevation models of technogenic massifs based on satellite coordinate determinations
At all stages of the life cycle of buildings and structures, geodetic support is provided by electronic measuring instruments – a laser scanning system, unmanned aerial vehicles, and satellite equipment. In this context, a set of geospatial data is obtained that can be presented as a digital model. The relevance of this work is practical recommendations for constructing a local quasigeoid model and a digital elevation model (DEM) of a certain accuracy. A local quasigeoid model and a DEM were selected as the study objects. It is noted that a DEM is often produced for vast areas, and, therefore, it is necessary to build a local quasigeoid model for such models. The task of assessing the accuracy of constructing such models is considered; its solution will allow obtaining a better approximation to real data on preassigned sets of field materials. A general algorithm for creating both DEM and local quasigeoid models in the Golden Software Surfer is presented. The constructions were accomplished using spatial interpolation methods. When building a local quasigeoid model for an area project, the following methods were used: triangulation with linear interpolation (the least value of the root mean square error (RMSE) of interpolation was 0.003 m) and kriging (0.003 m). The least RMSE value for determining the heights by control points for an area project was obtained using the natural neighbour (0.004 m) and kriging (0.004 m) methods. To construct a local quasigeoid model for a linear project, the following methods were applied: kriging (0.006 m) and triangulation with linear interpolation (0.006 m). Construction of the digital elevation model resulted in the least aggregate value of the estimated parameters: on a flat plot of the earth’s surface – the natural neighbour method, for a mountainous plot with anthropogenic topography – the quadric kriging method, for a mountainous plot – quadric kriging.
-
Date submitted2024-04-11
-
Date accepted2024-06-03
-
Date published2024-07-04
Assessment of the efficiency of acid mine drainage purification (using the example of copper-pyrite mines in the Middle Urals)
According to the results of the anti-rating of regions with extreme pollution of watercourses in the Sverdlovsk region, the largest number of polluted rivers has been recorded in recent years – more than a quarter of all high and extremely high pollution. One of the sources of pollution of natural water bodies in the Middle Urals are closed and flooded copper-pyrite mines, where acidic mine drainage continue to form and unload to the surface. Several of them have organized collection and a two-stage acidic drainage purification system, including neutralization with lime milk and settling in a clarifier pond. Despite the identical schemes, different indicators of pollutants are recorded during discharge into water bodies. The aim of the work is to evaluate the effectiveness of the applied acid mine drainage purification system and identify the parameters affecting the quality of treated mine water. Laboratory studies were performed using methods of flame emission spectrometry, flame atomic absorption, atomic absorption spectrometry, mass spectrometry with ionization in inductively coupled plasma, potentiometric, etc. It has been established that the existing mine drainage purification system at the Degtyarskii mine makes it possible to significantly reduce the concentrations of most toxic components of mine waters to almost standard values. At the Levikhinskii mine, the multiplicity of exceeding the maximum permissible concentrations reaches hundreds and thousands of times. To achieve a higher degree of purification, it is necessary that the duration of passive purification is sufficient for the reactant to interact with acidic waters. However, to ensure this possibility, it will require the creation of a cascade of ponds with an area of several thousand hectares. If the current two-stage system is quite effective for the Degtyarskii mine, then for Levikhinskii it is necessary to switch to the use of more modern systems, including three stages of purification.
-
Date submitted2022-05-26
-
Date accepted2022-11-17
-
Date published2022-12-29
Renovation method of restoring well productivity using wavefields
A stagewise theoretical substantiation of the renovation vibrowave method of influencing the near-wellbore zone of reservoir for restoring well productivity is presented. The area of treatment by the proposed method covers the reservoir with a heterogeneous permeability with fractures formed by fracking. In this method a decrease in concentration of colmatants occurs due to a change in direction of contaminants migration. Under the influence of pressure pulses, they move deep into the reservoir and disperse through the proppant pack. The results of mathematical modelling of the propagation of pressure wave and velocity wave and the calculations of particles entrainment in wave motion are presented.
-
Date submitted2021-12-21
-
Date accepted2022-06-20
-
Date published2022-11-10
Scientific justification of the perforation methods for Famennian deposits in the southeast of the Perm Region based on geomechanical modelling
The article presents the results of analysing geological structure of the Famennian deposits (Devonian) in the Perm Region. Numerical modelling of the distribution of inhomogeneous stress field near the well was performed for the two considered types of perforation. With regard for the geometry of the forming perforation channels, numerical finite element models of near-wellbore zones were created considering slotted and cumulative perforation. It is ascertained that in the course of slotted perforation, conditions are created for a significant restoration of effective stresses and, as a result, restoration of reservoir rock permeability. Stress recovery area lies near the well within a radius equal to the length of the slots, and depends on the drawdown, with its increase, the area decreases. From the assessment of failure areas, it was found that in case of slotted perforation, the reservoir in near-wellbore zone remains stable, and failure zones can appear only at drawdowns of 10 MPa and more. The opposite situation was recorded for cumulative perforation; failure zones near the holes appear even at a drawdown of 2 MPa. In general, the analysis of results of numerical simulation of the stress state for two simulated types of perforation suggests that slotted perforation is more efficient than cumulative perforation. At the same time, the final conclusion could be drawn after determining the patterns of changes in permeability of the considered rocks under the influence of changing effective stresses and performing calculations of well flow rates after making the considered types of perforation channels.
-
Date submitted2022-01-31
-
Date accepted2022-09-06
-
Date published2022-11-10
Filtration studies on cores and sand packed tubes from the Urengoy field for determining the efficiency of simultaneous water and gas injection on formation when extracting condensate from low-pressure reservoirs and oil from oil rims
- Authors:
- Nikolay A. Drozdov
Oil rims as well as gas condensate reservoirs of Russia's largest Urengoy field are developed by depletion drive without formation pressure maintenance, which has led to serious complications in production of oil, gas and condensate. In addition, field development by depletion drive results in low values of oil and condensate recovery. These problems are also relevant for other oil and gas condensate fields. One of the possible solutions is simultaneous water and gas injection. Rational values of gas content in the mixture for affecting gas condensate fields and oil rims of oil and gas condensate fields should be selected using the data of filtration studies on core models. The article presents the results of filtration experiments on displacement of condensate and oil by water, gas and water-gas mixtures when simulating the conditions of the Urengoy field. Simultaneous water and gas injection showed good results in the experiments on displacement of condensate, residual gas and oil. It has been ascertained that water-gas mixtures with low gas content (10-20 %) have a better oil-displacement ability (9.5-13.5 % higher) than water. An experiment using a composite linear reservoir model from cemented core material, as regards the main characteristics of oil displacement, gave the same results as filtration experiments with sand packed tubes and demonstrated a high efficiency of simultaneous water and gas injection as a method of increasing oil recovery at oil and gas condensate fields.
-
Date submitted2021-11-10
-
Date accepted2022-05-25
-
Date published2022-12-29
Predicting the permeability of the near-bottomhole zone during wave impact
The research reveals that during selection of a method to increase oil recovery it is necessary to take into account rheological features of fluid movement through the formation, effect of capillary forces and heterogeneity of reservoir properties of the productive formation in thickness and along the bedding. Low-frequency wave impact, which is used to increase production in oil fields, is considered. At low-frequency impact new fractures appear and existing fractures in rocks increase in size. The greatest increase in porosity and permeability of rocks occurs at an impact frequency up to 10 Hz. Dynamics of oscillation amplitude during wave's movement in saturated porous medium is studied in the paper: essential attenuation of amplitude occurs at distance up to 1 m from borehole axis. With increase of frequency from 1 to 10 Hz the intensity of amplitude's attenuation decreases. The technology was tested on a well in Perm region (Russia). The actual permeability value was 50 % higher than the predicted value. According to the results of hydrodynamic investigations processing, it was noted that the greatest increase of permeability took place near the wellbore, while away from the wellbore axis permeability remained almost unchanged. In order to refine the mathematical model for prediction of wave impact on rock permeability it is necessary to take into account interconnection of pore space structure, change of adhesion layer, as well as to study transfer of particles during vibration.
-
Date submitted2021-02-09
-
Date accepted2021-07-27
-
Date published2021-10-21
Development of an algorithm for determining the technological parameters of acid composition injection during treatment of the near-bottomhole zone, taking into account economic efficiency
Relevance of the research is due to the low proportion of successful hydrochloric acid treatments of near-bottomhole zones of carbonate reservoirs in the Perm region caused by insufficiently careful design and implementation of measures to stimulate oil production. Within the framework of this article, the development of a program is presented, which is based on an algorithm that allows determining the volume and rate of injection for an acid composition into a productive formation corresponding to the maximum economic efficiency during hydrochloric acid treatment. Essence of the proposed algorithm is to find the greatest profit from measures to increase oil recovery, depending on the cost of its implementation and income from additionally produced oil. Operation of the algorithm is carried out on the principle of enumerating the values of the volume and rate of injection for the acid composition and their fixation when the maximum difference between income and costs, corresponding to the given technological parameters of injection, is reached. The methodology is based on Dupuis's investigations on the filtration of fluids in the formation and the results of the experiments by Duckord and Lenormand on the study of changes in the additional filtration resistance in the near-well zone of the formation when it is treated with an acid composition. When analyzing and including these investigations into the algorithm, it is noted that the developed technique takes into account a large number of factors, including the lithological and mineralogical composition of rocks, technological parameters of the injection of a working agent and its properties, well design, filtration properties of the formation, properties of well products. The article provides an algorithm that can be implemented without difficulty using any programming language, for example, Pascal. Selection of the optimal values for the volume and rate of injection is presented in this paper, using the example of a production well at the Chaikinskoye oil field, located within the Perm region. Introduction of the developed algorithm into the practice of petroleum engineering will allow competent and effective approach to the design of hydrochloric acid treatments in carbonate reservoirs without a significant investment of time and additional funds.
-
Date submitted2021-02-05
-
Date accepted2021-03-30
-
Date published2021-04-26
Assessment of negative infrastructural externalities when determining the land value
- Authors:
- Elena N. Bykova
The work forms and substantiates the concept of land value, based on a new institutional theory. The infrastructural component of the cost of land in the presented concept determines, on the one hand, the efficiency of the use of natural resources, properties, demand for land on the market, on the other hand, the costs, which are determined not only by capital investments in construction of engineering infrastructure, but also by losses associated with restrictions on activities within zones with special conditions for territory use, creation of unfavorable conditions for economic activity, small contours, irregularities and others on a specific land plot, which are external negative infrastructural externalities that create losses of rights holders of land plots that are not compensated by the market, falling within the boundaries of these zones. Methods for assessing the impact of such negative infrastructural externalities on the cost of land encumbered by zones in different conditions of land market activity have been developed and tested, based on an expert-analytical approach (depressed market); the ratio of market values of land plots encumbered and unencumbered by a specific zone, and qualimetric modeling (inactive market); modeling by introducing into the model the factor of presence of zones with special conditions for territory use, based on the grouping of zones according to similar regulations for use, or by introducing the parameters of this factor (active market). Methods for taking into account spatial deficiencies and compensating for restrictions and prohibitions on activities on the territory of land plots with an individual market assessment are proposed.
-
Date submitted2019-06-22
-
Date accepted2019-09-11
-
Date published2020-04-24
Effective capacity building by empowerment teaching in the field of occupational safety and health management in mining
The paper is dealing with a developed concept named Empowerment Teaching, which is based on practical teaching experience gained in various mining universities. It is demonstrated that this concept can be used to increase the effectiveness of knowledge transfer to mining countries in the world, as well as to overcome cultural barriers between lecturers and their students. The two models of participatory training, which are proposed to be named “physical” and “emotional” models, are portrayed. The authors are convinced that participatory training methods can be an ideal answer to a challenge associated with workers’ competencies in mining, namely – the potential of highly motivated and well-educated young academics is often diminished by a lack of ability to apply their knowledge. A special emphasis is made on the possible application of empowerment teaching for educational and training activities in the field of occupational safety and health (OSH), which is a matter of utmost importance for the mining industry. Several benchmarking initiatives in the field of OSH (“safety culture”, zero-accident vision) are underlined to be encouraged and promoted by means of new teaching methods. The examples of successful international cooperation among universities are given, as well.
-
Date submitted2019-07-10
-
Date accepted2019-08-30
-
Date published2019-12-24
Methodology for calculating technical efficiency of power sections in small-sized screw downhole motors for the «Perfobur» system
With an increase in the share of old and low-yield wells and for the efficient exploitation of fields, it is necessary to include low-capacity formations into production. There are many wells where sidetracking and hydraulic fracturing are difficult due to the close proximity of the gas cap and underlying water caused by geological and technological reasons, and the use of existing secondary drilling-in technologies is not effective due to the extensive colmatated zone or annular circulation. Relevance of radial drilling technologies is growing, which allows drilling-in of the formation with a network of extended channels to establish high-quality hydraulic communication between the formation and the well without affecting the permeability of the formation. In contrast to radial drilling technologies using hydraulic washing, technical system (TS) «Perfobur» uses small-sized screw downhole motors (SDM) and rock cutting tools for channel construction. For efficient milling of production casing and destruction of rock, the hydraulic downhole motor must have high torque, and for the possibility of drilling with a high rate of angle gain, it must have short power section. Existing Russian and foreign SDM have limited number of standard sizes and do not meet the requirements specified for the development of the downhole module of TS «Perfobur». The paper discusses the development of universal small-sized sectional screw downhole motors for milling casing strings and drilling a network of branched channels of super-small diameter and radius of curvature as a part of the TS «Perfobur». Methodology proposed in the article for selecting optimal configuration of the SDM power sections allows constructing small-sized sectional downhole motor that meets the technical requirements and has improved characteristics compared to standard SDM.
-
Date submitted2019-03-24
-
Date accepted2019-05-13
-
Date published2019-08-23
Calculation of Oil-saturated Sand Soils’ Heat Conductivity
- Authors:
- J. Sobota
- V. I. Malarev
- A. V. Kopteva
Nowadays, there are significant heavy high-viscosity oil reserves in the Russian Federation with oil recovery coefficient not higher than 0.25-0.29 even with applying modern and efficient methods of oil fields development. Thermal methods are the most promising out of the existing ways of development, main disadvantage of which is large material costs, leading to the significant rise in the cost of extracted oil. Thus, creating more efficient thermal methods and improving the existing ones, is the task of great importance in oil production. One of the promising trends in enhancing thermal methods of oil recovery is the development of bottomhole electric steam generators. Compared to the traditional methods of thermal-steam formation treatment, which involve steam injection from surface, well electrothermal devices can reduce energy losses and improve the quality of steam injected into the formation. For successful and efficient organization of oil production and rational development of high-viscosity oil fields using well electrothermal equipment, it is necessary to take into account the pattern of heat propagation, both in the reservoir and in the surrounding space, including the top and bottom. One of the main values characterizing this process is the heat conductivity λ of oil-bearing rocks. The article describes composition of typical oil-saturated sand soils, presents studies of heat and mass transfer in oil-saturated soils, reveals the effect of various parameters on the heat conductivity of a heterogeneous system, proposes a method for calculating the heat conductivity of oil-bearing soils by sequential reduction of a multicomponent system to a two-component system and proves the validity of the proposed approach by comparing acquired calculated dependencies and experimental data.
-
Date submitted2019-01-22
-
Date accepted2019-03-16
-
Date published2019-06-25
Key factors of public perception of carbon dioxide capture and storage projects
- Authors:
- S. V. Fedoseev
- Pavel S. Tcvetkov
One of the major challenges of the modern world is the problem of global warming, the solution of which requires the implementation of a set of strategic projects in the field of transition of the energy sector to the path of environmentally balanced development. One of the ways to implement this transition is the development of technologies for capturing and storage of technogenic carbon dioxide, which is recognized as the main one of greenhouse gases. At the same time, in the Russian context, the most expedient is the implementation of technological chains for capturing and storing CO 2 which are aimed at enhanced oil recovery, the effectiveness of which has been proven by world practice. Implementation of these projects requires consolidation of efforts of many parties, including government agencies, enterprises-issuers (power generating facilities and energy-intensive industry), oil-producing enterprises, non-state environmental organizations, media and public. World practice has many examples when uncoordinated actions of one of the stakeholders led to the closure of such a project, and therefore it is necessary to develop a mechanism of interaction between them, taking into account the specifics of Russian conditions. One of the least studied and controversial aspects of this interaction is to involve the public in the implementation of national carbon intensity programs and the local population in the implementation of a specific project. Research in this field has been conducted in the world over the past 14 years, which allowed the current research base to be used to develop fundamental principles for the development and promotion of CO 2 capture and storage technologies in Russia. Key factors affecting the perception of such projects by public were also analyzed and systematized. The research identified the main arguments for and against the development of CO 2 capture and storage technologies.
-
Date submitted2019-01-17
-
Date accepted2019-03-20
-
Date published2019-06-25
Improving methodological approach to measures planning for hydraulic fracturing in oil fields
Goal of the research is development of an integrated approach to the planning of hydraulic fracturing (HF) treatment taking into account geo-technical, hydrodynamic, technological and economic criteria for the selection of wells for inclusion in the programs of HF with increasing importance of economic criteria. Stages of formation of the program for HF of the oil company are selected, systematized and analyzed. It is shown that high potential effectiveness of enhanced oil recovery method in fields with hard-to-recover reserves, on the one hand, and the complexity and high cost of application, on the other, determine the need to optimize the parameters of this business process at all stages of implementation and improve its planning methods. The priority directions for improving the hydraulic fracturing planning were justified: a clear definition of the criterion for the payback period of hydraulic fracturing activities, taking into account their technological features, improving the procedure for calculating the costs of implementing this technology and improving the reasonableness of selecting candidate wells for inclusion in the hydraulic fracturing program. Feasibility of using an additional criterion in the formation of hydraulic fracturing programs – marginal minimum cost-effective wall capacity – has been shown and a method for calculating it has been developed. The use of this criterion will allow to take into account not only technological limitations, but also limits of economic efficiency of conducting hydraulic fracturing at each specific well and, at the preliminary selection of candidate wells, exclude a priori unprofitable measures.
-
Date submitted2017-10-29
-
Date accepted2017-12-31
-
Date published2018-04-24
Risk assessment of accidents due to natural factors at the Pascuales – Cuenca multiple-use pipeline (Ecuador)
- Authors:
- Dzh. Zambrano
- S. V. Kovshov
- E. A. Lyubin
The natural aspects of the accident risk at the Pascuales – Cuenca multiple-use pipeline (Ecuador) are analysed in the paper. The Russian Methodological recommendations for the quantitative analysis of accident risks at hazardous production plants of oil trunk pipelines and oil product trunk pipelines issued in 2016 are used as a methodological framework due to relatively poorly defined evaluation mechanism for natural factors of accidents at oil trunk pipelines in the most widespread international accident risk assessment methodologies. The methodological recommendations were updated to meet the environmental conditions of oil pipelines of Latin America. It was found that the accidents due to natural factors make up approximately 15 % of cases at oil trunk pipelines in Ecuador. Natural geographical features of the areas surrounding the main Ecuadorian Pascuales–Cuenca oil trunk pipeline and its relatively short length allow defining three zones along the line in terms of the accident risk: lowland coastlines, high plateaus, and foothills. Calculations and analysis revealed that the maximum predicted specific frequency of accidents is characteristic of the lowland seaside area. The evidence showed that physical and chemical properties of soils and significant seismic activity are the root causes of failures.
-
Date submitted2010-07-28
-
Date accepted2010-09-07
-
Date published2011-03-21
Modelling cavities nearwell areas for studyind of possibilities neitron well methods
- Authors:
- N. A. Poznyakova
Look into the possibility neutron method geophysical logging for determination zones of cavity nearwell areas gas reservoirs and determine the filler cavities. Relevant practicability using these methods on underground gas storage. Give an example these research on model and real conditions.
-
Date submitted2009-10-18
-
Date accepted2009-12-09
-
Date published2010-09-22
Influence of blocky-hierarchy structure of geological medium on the forming of natural and technogenic geodynamic fields in the North-West part of the Amur geoblock
- Authors:
- I. Yu. Rasskazov
- B. G. Saksin
On the example of the South-Argun uranium ore district of Zabaikalie consideration is given to the interaction of regional and local fields of stresses. The district includes a number of deposits prone to rock bursts. The performed analysis contains data on recent geodynamics of the explored part of the Amur geoblock as well as on geomechanical and geologo-structural materials of Tulukuev caldera and of Antey deposit. It is shown that with the use of the M.A. Sadovsky relationship the indices of local structural forms of a row are subjected to unified laws of deformation and fracturing. Conclusion was made that at the beginning of deposit exploitation the direction of action of stress field within rock mass conformed to regional one, and then it considerably changed under influence of large-scale mining operations.
-
Date submitted2009-09-10
-
Date accepted2009-11-11
-
Date published2010-06-25
Stages of training activation methods development
- Authors:
- M. A. Perfilova
The article is dedicated to the problem of developing methods of training activation. Historical and pedagogical background for the development of these methods and distinguishes the stages of training activation methods development from the ancient times till nowadays are analysed. The brief chronological survey is presented tabular. The main features of the methods of active training are pointed out.
-
Date submitted2009-09-19
-
Date accepted2009-11-24
-
Date published2010-06-25
The forecast of the stress-strain state of massifs rocks in the bed deposits
- Authors:
- A. P. Gospodarikov
- M. A. Zatsepin
The variety of the mining and geological conditions with further increasing in depth of the development of bedded deposits leads to necessity for the analysis of stress-strain state near different types of excavations.
-
Date submitted2009-09-15
-
Date accepted2009-11-02
-
Date published2010-06-25
Mathematical modeling of stress-strain state of the mined seam deposits
- Authors:
- A. P. Gospodarikov
- M. A. Zatsepin
Development of bedded deposits is associated with man-caused distortion of specific environment – the rock massifs, which are very complicated in their composition, can vary significantly in mechanical properties and is characterized with a wide variety of laws and techniques to assess its stress-strain state.
-
Date submitted2009-08-29
-
Date accepted2009-10-30
-
Date published2010-02-01
The unit for gravity concentration of fine particles
- Authors:
- Ya. V. Kuskova
It was made new modification of device for allows increasing recovery, to increase productivity and to lower size of concentrated particles. The device has a deck executed as a circle, which divides into two sectors; each sector has circular rifles with progressively growing height from the centre to periphery of a deck. The table is equipped with the high-frequency step-by-step engine ensuring continuous rotation of a table and submission counter impulses for shear of particles in a direction, opposite to rotation of a table. The quantity of angle sectors can be various. Testing of prototype of a table has confirmed an opportunity of increase of recovery, decrease size of extracted dense minerals and increase of throughput.
-
Date submitted2009-07-22
-
Date accepted2009-09-22
-
Date published2010-04-22
Surveying methods for providing geodynamical safety of mining operations
- Authors:
- E. N. Kuznetsova
It is impossible to solve the main task of geodynamics without using technologies including traditional measurements of bench marks excursion, as well as new technologies of the end of XX – beginning of XXI century, such as photogrammetry, global positioning system, laser measurements and technologies of geophysical well logging. The paper concerns with the analysis of the mine surveying methods facilitating the solution of tasks related to the geodynamical safety assurance.
-
Date submitted2009-07-16
-
Date accepted2009-09-28
-
Date published2010-04-22
Efficient numerical methods for geotechnical problems
- Authors:
- M. A. Karasev
This article give a general overview of methods to solve large scale geotechnical problems, nonlinear high deformation and plastic problems, self contact of strata and application of high performance computing.
-
Date submitted2008-10-25
-
Date accepted2008-12-29
-
Date published2009-12-11
Geoelectrical investigation of promising oil and gas bearing areas in the south part of Siberian plat-form
The investigations were carried out in Eastern Siberia on the Ust-Orda national region territory using the groups of methods on direct and alternating current. Multicomponent registration of electrical and electromagnetic parameters has been used. Field data interpretation stage included adaptation of software for a concrete experimental data, substantiation of interpretational models formation methods and the analysis of all a priori information. As a result, quantitative estimations of thickness and geoelectrical parameters of geological complexes were obtained. Moreover, complex tectonic structures were allocated and the most promising areas for detailed works were chosen.
-
Date submitted2008-10-13
-
Date accepted2008-12-15
-
Date published2009-12-11
A complex of gravi-, magneto-, electroprospecting аnd geoelectrochemical methods for local prediction and prospecting for hydrocarbon deposits
It is proposed to use interpretational spatial distributions of effective parameters of the medium under investigation instead of measured fields in the process of comprehensive prediction-prospecting investigations. There are used effectively: effective density, effective magnetization, intensity of probable sources of geochemical anomalies.
-
Date submitted2008-10-30
-
Date accepted2008-12-14
-
Date published2009-12-11
On correlation of element concentrations in spray нaloes of dispersion being fixed with different geoelectrochemical methods
- Authors:
- O. F. Putikov
- E. G. Margovich
The theoretical basis for correlation between the results of two geoelectrochemical methods at different depths of sampling is presented. The field data confirm the conclusion.