Methodology for calculating technical efficiency of power sections in small-sized screw downhole motors for the «Perfobur» system
- 1 — «Perfobur» LLC
- 2 — National University of Oil and Gas «Gubkin University»
- 3 — Ufa State Petroleum Technological University
- 4 — Ufa State Petroleum Technological University
- 5 — Saint-Petersburg Mining University
Abstract
With an increase in the share of old and low-yield wells and for the efficient exploitation of fields, it is necessary to include low-capacity formations into production. There are many wells where sidetracking and hydraulic fracturing are difficult due to the close proximity of the gas cap and underlying water caused by geological and technological reasons, and the use of existing secondary drilling-in technologies is not effective due to the extensive colmatated zone or annular circulation. Relevance of radial drilling technologies is growing, which allows drilling-in of the formation with a network of extended channels to establish high-quality hydraulic communication between the formation and the well without affecting the permeability of the formation. In contrast to radial drilling technologies using hydraulic washing, technical system (TS) «Perfobur» uses small-sized screw downhole motors (SDM) and rock cutting tools for channel construction. For efficient milling of production casing and destruction of rock, the hydraulic downhole motor must have high torque, and for the possibility of drilling with a high rate of angle gain, it must have short power section. Existing Russian and foreign SDM have limited number of standard sizes and do not meet the requirements specified for the development of the downhole module of TS «Perfobur». The paper discusses the development of universal small-sized sectional screw downhole motors for milling casing strings and drilling a network of branched channels of super-small diameter and radius of curvature as a part of the TS «Perfobur». Methodology proposed in the article for selecting optimal configuration of the SDM power sections allows constructing small-sized sectional downhole motor that meets the technical requirements and has improved characteristics compared to standard SDM.
References
- Baldenko D.F., Baldenko F.D., Gnoevykh A.N. Single screw hydraulic machines. Vol. 1, 2005. Vol. 2, 2007. Moscow: IRTs Gazprom (in Russian).
- Vadetskii Yu.V., Kaplun V.A., Knyazev I.K. Features of drilling technology with screw downhole motors. Neftyanoe khozyaistvo. 1976. N 6, p. 7-10 (in Russian).
- Gusman M.T., Nikomarov S.S., Kochnev A.M. New volumetric downhole motor. Neftyanoe khozyaistvo. 1970. N 11, p. 8-12 (in Russian).
- Zakharov Yu.V. The study of axial forces acting in a downhole screw motor. Mashiny i neftyanoe oborudovanie. 1978. N 5, p. 9-11 (in Russian).
- Kas'yanov V.M. Hydraulic machines and compressors. Moscow: Nedra, 1981, p. 295 (in Russian).
- Korotaev Yu.A. Technological ensuring of durability for multi-lobe screw gerotor mechanisms of hydraulic downhole motors. Moscow: VNIIOENG, 2003, p. 259 (in Russian).
- Kochnev A.M., Zakharov Yu.V., Nikomarov S.S. Some features of the working process in a downhole motor. Mashiny i neftyanoe oborudovanie. 1979. N 1, p. 19-23 (in Russian).
- Kupavykh K.S., Kupavykh A.S., Morenov V.A. Analysis of Implementation Effectiveness of Two Working Fluids Characterized by Different Viscoelastic Characteristics at Hydrodynamic Impact on the Borehole Bottom Zone. Nauka i tekhnika. 2019. Vol. 18 (2), p. 164-170. DOI: 10.21122/2227-1031-2019-18-2-164-170 (in Russian).
- Lyagov A.V., Lyagov I.A. Selection of permissible radii of curvature in super-small diameter wells (channels) for «Perfobur» technical system. Ekspozitsiya Neft' Gaz. 2014. N 6, p. 47-52 (in Russian).
- Lyagov I.A. Analysis of the field tests' results of "Perfobur" technical system. Analytical synthesis of "Perfobur" base units of increased reliability for drilling extra-long channels along a predicted trajectory. Neftegazovoe delo. 2014. N 1, p. 52-76 (in Russian).
- Molodilo V.I., Korotaev Yu.A., Medvedev A.Yu. Automation of the well drilling process using screw downhole motors. Avtomatizatsiya, telemekhanizatsiya i svyaz' v neftyanoi promyshlennosti. 2002. N 1-2, p. 17-21 (in Russian).
- Plotnikov V.M. Bench research of the screw downhole motor's characteristics at using aerated flushing liquids as a working agent. Trudy VNIIBT. Sbornik statei. OAO «NPO «Burovaya Tekhnika». Moscow: Izd-vo «Sovremennye tetradi». 2008. N 2 (70), p. 338-340 (in Russian).
- Selivanov S.M., Baletinskikh D.I. A new page in the development of SDM designs. Burenie i neft'. 2011. N 7-8, p. 64-67.
- Mass-produced motors. «Radius-Servis» enterprise. URL: http://radius-s.ru/oborudovanie/vintovye-zaboynye-dvigateli/ dvigateli/ (date of access: 02.07.2019) (in Russian).
- Technical characteristics of the SDM with a diameter of 43-127 mm. «VNIIBT-Drilling Instrument» enterprise. URL: http://www.vniibt-bi.ru/products/vintovye-zaboynye-dvigateli-vzd-klapany-filtry-i-shlamouloviteli/dimension43-127mm/ (date of access: 02.07.2019) (in Russian).
- Shipulin A.V., Kupavykh K.S., Kupavykh A.S. Improving the energy efficiency of the pumping unit during the formation of pulsed hydraulic fracturing. Nauchno-tekhnicheskie vedomosti SPbGPU. 2016. N 4, p. 39-44. DOI: 10.5862/JEST.254.5 (in Russian).
- I.A.Lyagov, N.I.Vasilev, M.Reich, M.Mezzetti Analytical research and experimental tests on the technology for drilling small diameter channels with small radius of curvature. Oil Gas European Magazine. 2014. Vol. 40. Iss. 3, p. 124-129.
- Downhole Motor. Lilin Group. URL: http://lilingroup.com/product-Motor.asp (date of access: 02.07.2019).
- Samuel R., Baldenko D., Baldenko F. Positive Displacement Motors. Theory and Applications. Houston, Texas: Sigmaquadrant, 2015, p. 434.