-
Date submitted2024-06-12
-
Date accepted2024-07-18
-
Date published2025-04-25
Development of parameters for an industry-specific methodology for calculating the electric energy storage system for gas industry facilities
- Authors:
- Ivan S. Tokarev
The issue of determining the main parameters of electric energy storage systems – power and energy intensity – is being considered, the determination of which is a fundamentally important task when introducing such devices into the power supply systems of enterprises for both technical (technological) and economic reasons. The work analyzes problems that can be solved by installing electricity storage systems at gas industry facilities. An industry-wide methodology has been developed for calculating the parameters of an electricity storage system based on traditional methods and methods aimed at minimizing the standardized cost of electricity with adaptation to the conditions of the gas industry. A distinctive feature of the presented methodology is the ability to determine the power and energy intensity of electricity storage systems when performing several functions. The methodology was tested at a typical gas industry facility – the Yarynskaya compressor station of OOO Gazprom Transgaz Ukhta, a characteristic feature of which is an autonomous power supply system. An example is given of calculating the electricity storage normalized cost using an improved LCOS indicator, which takes into account the effect of changing the fill factor of the electrical load schedule on the amount of gas consumption by a power plant for its own needs. To confirm the economic efficiency of introducing electricity storage systems calculated using the above methodology, calculations of the integral effect, net present value and efficiency index are presented.
-
Date submitted2023-04-10
-
Date accepted2024-12-27
-
Date published2024-04-25
Optimization of specific energy consumption for rock crushing by explosion at deposits with complex geological structure
The selection of efficient drilling and blasting technology to achieve the required particle size distribution of blasted rock mass and reduce ore dilution is directly related to the accurate definition of rock mass properties. The zoning of the rock massif by its hardness, drillability and blastability does not consider the variability of the geological structure of the block for blasting, resulting in an overestimated specific consumption of explosives. The decision of this task is particularly urgent for enterprises developing deposits with a high degree of variability of geological structure, for example, at alluvial deposits. Explosives overconsumption causes non-optimal granulometric composition of the blasted rock mass for the given conditions and mining technology. It is required to define physical and mechanical properties of rocks at deposits with complex geological structure at each block prepared for blasting. The correlation between the physical and mechanical properties of these rocks and drilling parameters should be used for calculation. The relation determined by the developed method was verified in industrial conditions, and the granulometric composition of the blasted rock mass was measured by an indirect method based on excavator productivity. The results demonstrated an increase in excavation productivity, thus indicating the accuracy of given approach to the task of identifying the rocks of the blasted block.
-
Date submitted2022-10-26
-
Date accepted2023-02-13
-
Date published2023-07-19
Determination of the grid impedance in power consumption modes with harmonics
The paper investigates the harmonic impedance determination of the power supply system of a mining enterprise. This parameter is important when calculating modes with voltage distortions, since the determined parameters of harmonic currents and voltages significantly depend on its value, which allow the most accurate modeling of processes in the presence of distortions in voltage and current. The power supply system of subsurface mining is considered, which is characterized by a significant branching of the electrical network and the presence of powerful nonlinear loads leading to a decrease in the power quality at a production site. The modernization of the mining process, the integration of automated electrical drive systems, renewable energy sources, energy-saving technologies lead to an increase in the energy efficiency of production, but also to a decrease in the power quality, in particular, to an increase in the level of voltage harmonics. The problem of determining the grid harmonic impedance is solved in order to improve the quality of design and operation of power supply systems for mining enterprises, taking into account the peculiarities of their workload in the extraction of solid minerals by underground method. The paper considers the possibility of determining the grid impedance based on the measurement of non-characteristic harmonics generated by a special nonlinear load. A thyristor power controller based on phase regulation of the output voltage is considered as such a load. Simulation computer modeling and experimental studies on a laboratory test bench are used to confirm the proposed method. The recommendations for selecting load parameters and measuring device connection nodes have been developed.
-
Date submitted2021-04-19
-
Date accepted2021-10-18
-
Date published2021-12-16
Mutual spectral densities calculation of the moments of resistance on the peat milling unit working bodies
- Authors:
- Konstantin V. Fomin
When performing technological operations in the peat industry, various units with milling-type working bodies are used. They differ in design, layout, number and type of cutting elements, operating modes, and may have one or more working bodies. During operation, random forces and moments act on the cutters, which have a dramatically variable nature, which is associated with the periodic interaction of the knives with the peat deposit, its structural heterogeneity, variations in the milling depth, physical and mechanical properties of peat, the rotational speed of the cutter and the movement speed of the machine. In this case, significant dynamic loads arise in the structural elements, which leads to a decrease in their reliability, deterioration of the energy characteristics of the engine operation and technical and economic indicators of use. In the dynamic analysis of drive elements, when using machines with several working bodies, it is necessary to know both spectral and mutual spectral load densities. For their calculation, expressions were obtained that take into account the physical and mechanical properties of peat, the operating modes of the unit and their probabilistic characteristics, as well as the design features of the working body. The expressions are obtained for the case when there are several working bodies with the same diameters and the number of knives in the cutting plane. In this case, the number of planes, width, type of cutting element and type of cutting (locked, semi-locked, etc.) may differ. As an example of using the developed approaches, the calculation of spectral and mutual spectral densities of moments on cutters and loads in the drive elements of the machine for surface-layer milling MTF-14 is presented.
-
Date submitted2019-06-19
-
Date accepted2019-09-11
-
Date published2020-02-25
Method for estimating the spectrum density of the resistance moment on the working body of a peat milling unit
- Authors:
- K. V. Fomin
The main source of dynamic loads in the drive elements and the design of the peat milling unit is the working body. The forces of external resistance arising in the process of performing a technological operation are sharply variable, random in nature. The article proposes a model of formation of the moment of resistance on the mill when interacting with peat. The case when there are several cutting planes with the same radius at the ends of the cutting elements is considered. When developing the model, it was taken into account that the operating conditions of the knives, determined by the type of cutting (blocked, semi-blocked, etc.), their width and type in each cutting plane can vary. Factors that determine the nature of loading, such as the frequency of interaction of the cutting elements with the fallow and the randomness of the operating conditions of the unit, lead to the presentation of the loads in the form of a sequence of pulses with random parameters. Expressions are obtained for determining the spectral density of the moment of resistance on the mill at the design stage, taking into account its design, operating modes, physico-mechanical properties of peat and their probabilistic characteristics. To illustrate the application of the developed approaches, a technique is presented for determining the spectral density of the moment on the working body of deep milling machines and in their drive elements based on a linear model. An example of calculation is given, and the obtained expressions are verified on the basis of experimental data. The probabilistic characteristics of the loads on the mill serve as initial information for the dynamic analysis of the drive system and the design of the unit, its strength analysis, the selection of optimal parameters and operating modes.
-
Date submitted2018-11-03
-
Date accepted2019-01-16
-
Date published2019-04-23
Interpretation of the tracer investigation results considering convective mass transfer
- Authors:
- V. A. Korotenko
- S. I. Grachev
- A. B. Kryakvin
The paper discusses the results of interpreting well tracer studies. It is shown that from the law of mass conservation it follows that when filtering a volume of an indicator, part of the injected tracer flows into the matrix. With the flow of fluid containing the indicator from the low-filtration resistance channel (LFR) into the surrounding matrix, the linear dimensions of the flow area depend on the permeability and porosity properties of the high-permeability channel and the matrix. While another part of the tracer moves toward the production well, its mass is lost due to diffusion processes. From the solution of the diffusion equation, it follows that the initial concentration of the tracer decreases in the course of filtration along the LFR channel. To interpret the results of the tracer studies, different cases of the LFR channels' location in the volume of the productive formation are considered. The varied parameter w allows characterizing the presence of several peaks in the concentration of the indicator and calculation the filtration parameters of the LFR channels. Depending on the known technological indices, several methods for determining pore volumes in the LFR channels have been proposed. To reduce the water cut in producing wells and to apply the technology of changing or aligning the injectivity profiles, calculations of the pore channels' radii in the mass of highly permeable seams are presented. It is shown that the volume of the chemical reagent pumped into the injection well to isolate the LFR channel is affected by the linear dimensions of the drainage area for the aqueous solution of indicator. Examples of the calculation for the permeability and porosity parameters of the LFR, the volume of pore channels necessary to isolate water inflow, and the radii of pore filtration channels, which influence the selection of the size of chemical reagent molecules, are given.
-
Date submitted2015-12-18
-
Date accepted2016-02-01
-
Date published2016-12-23
Simulation of onboard power supply system for small hydrographic vessel «Vaygach»
- Authors:
- I. A. Pankov
- V. Ya. Frolov
Computer simulation is a method resorted to more and more frequently for the development of the prospective power supply systems, in particular the vessel power supply system. It provides valuable insights into the transient processes and indicators of electric power quality in the system without building its physical model, thus significantly improving the efficiency and quality of the physical model. Nowadays MathLab package with Simulink application is used with increasing frequency for simulation of such systems. The paper presents a model of the power supply system of small hydrographic vessel ‘Vaygach’ built in MatLab environment. The system vulnerabilities and their remedies have been identified. Changes in sinusoid before and after the non-linear load on the network have been demonstrated and solutions for improving the non-linear distortion factor are proposed. The model developed for the vessel power supply system can be used for building models of different vessels.
-
Date submitted2015-08-20
-
Date accepted2015-10-17
-
Date published2016-04-22
Increasing the accuracy of the fast laser measurments transparent solid and liquid films thicknesses
- Authors:
- A. B. Fedortsov
Nondestructive optical methods for measuring of the «thick» films thickness of the order of 0,001-1,00 mm are analyzed. It is shown that using the laser beam radiation and modern optical and electronic schemes possible to decrease the time of single measurement to 1ms and less at the measuring frequency of 10-50 Hz. The possibility of measuring thickness and spreading coefficient and evaporation kinetics of liquid films is demonstrated. A new computer method of the data processing aimed to determine the film thickness from the angle dependence of the laser beam reflection coefficient by the film is offered. The offered procedure and the experimental technique realizing it permits to decrease the thickness determination uncertainty to the order of ten.
-
Date submitted2010-07-28
-
Date accepted2010-09-30
-
Date published2011-03-21
Ingineering geological problems of high-rise construction with underground space development in Saint-Petersburg
- Authors:
- R. E. Dashko
- A. M. Zhukova
The history of high-rise construction is considered summarily. The main features of high-rise buildings and difficulties connected with theirs engineering and construction especially with underground space development and deep excavations in soft water saturated soils are characterized. Territorial construction guides «Residential and social high-rise buildings» prevail in Saint-Petersburg are analyzed in the context of recommendations for reliable basement choice. Brief description of Pre-Quanernary clays (Upper Vendian clays and Lower Cambrian clays) as basement for high-rise constructions are given. It is placed emphasis that the main feature of Pre-Quaternary clays is zone sequence of physical and mechanical properties and fissuring in depth. Physical and mechanical properties of Upper Vendian clays, Lower Cambrian clays and glacial clays are given. In addition, it is confirmed that glacial soils is not recommended to use as a basement for high-rise buildings.
-
Date submitted2010-07-29
-
Date accepted2010-09-27
-
Date published2011-03-21
Efficiency increasing of condenser batteries operation in mining enterprise`s electric circuits
- Authors:
- A. N. Skamin
This work contains the method of effective reactive power compensation at the expense of high harmonics reduction. The decrease of condenser batteries overloading from the high harmonics is based on variation of condenser power depending on current and voltage spectral structure, electric network parameters and load power.
-
Date submitted2010-07-10
-
Date accepted2010-09-15
-
Date published2011-03-21
Reduction methods of high harmonics influence on the electric equipment operation
- Authors:
- Ya. E. Shklyarsky
- A. N. Skamin
This work contains brief analysis of high harmonics reduction methods. It is offered to make a choice between reduction methods of high harmonics influence on condenser batteries depending on factors of harmonics occurrence. Definition algorithm for the most effective method of high harmonics reduction on condenser batteries operation is created.
-
Date submitted2010-07-14
-
Date accepted2010-09-07
-
Date published2011-03-21
Substantiation of pumped volumes of flow angularity compositions in injection wells
- Authors:
- A. R. Mavliev
- M. K. Rogachev
- D. V. Mardashov
The method of calculation pumped volumes of flow angularity compositions in injection wells, which based on combination of the seepage theory, laboratory investigation and field experience is developed.
-
Date submitted2010-07-16
-
Date accepted2010-09-06
-
Date published2011-03-21
The aboveground oil pipeline temperature regimes calculation
- Authors:
- S. Yu. Trapeznikov
The theoretical and experimental investigations of the highviscosity oil transportation temperature regimes to improve the pipeline efficiency are caused by the insufficient knowledge of its heat transfer process. The dependencies for the hydraulic resistance coefficient and the dimensionless heat transfer coefficient of Nusselt are proposed.
-
Date submitted2009-09-26
-
Date accepted2009-11-22
-
Date published2010-06-25
Use of mosfet for the control of dielectric characteristics
- Authors:
- N. S. Pshchelko
- A. S. Mustafaev
In this work a device for measurement on a constant voltage of the basic electric characteristics of high-resistance dielectric materials and products from – their electric capacitance and resistance – is developed. The principle of work of the device is based on use of transients in connected in sereies elements having electric capacity and resistance. In the electric circuit of the device the MOSFET with high entrance resistance is used. The device on the basis of the MOSFET for measurement of surface potential of dielectrics is considered also. Use of this device is especially effective at measurement of electret surface potential. Results of research of electrets on a basis of silicon dioxide are discussed.