-
Date submitted2023-10-03
-
Date accepted2024-11-07
-
Date published2025-02-25
Investigation of the effectiveness of the use of various substances for dust suppression during the transshipment of granular sulfur
The article is devoted to the problem of dusting during the transshipment of granular sulfur and existing methods of dust suppression. The analysis of various methods for reducing dust emission at granulated sulfur storage and transportation facilities is presented. The necessity of using special reagents to increase the efficiency of dust suppression and re-granulation of sulfur crushed by abrasion is noted. The sulfur dust obtained from the port terminal during the transshipment of technical sulfur was analyzed for granulometric composition. The results of experimental studies of the effectiveness of the use of various substances for sulfur dust suppression (alkyl polyglycosides, sodium silicate, starch) are presented. The laboratory installation was a hopper, inside which a test sample of dusty material was placed. The sample was subjected to an aerodynamic effect by an air flow at a given speed. The concentrations of suspended solids were measured with a dust meter-nephelometer with a sampling tube placed in the geometric center of the hopper. The effectiveness of dust suppression agents was determined based on a comparison of the concentration values obtained on dry and treated samples. For dust suppression at granulated sulfur treatment facilities, it is proposed to use a composition based on nonionic surfactants represented by a mixture of C12-14-alkylglycosides oligomers (1-1.5 %), additionally containing a mixture of amylose and amylopectin polysaccharides in the form of soluble starch (1-2.5 %) and water. The dust suppressor showed consistently high dust suppression efficiency both when measured immediately after irrigation (98.3 %) and after the expected time (99.7 %). The developed composition provides an increase in the dust-suppressing ability of the solution and the elimination of the possibility of repeated dusting due to the formation of a polymer film on the surface, as well as the regranulation of the product crushed by abrasion.
-
Date submitted2024-04-16
-
Date accepted2024-06-03
-
Date published2024-07-04
Quantitative determination of sulfur forms in bottom sediments for rapid assessment of the industrial facilities impact on aquatic ecosystems
- Authors:
- Ivan P. Sverchkov
- Vladimir G. Povarov
The article describes an X-ray fluorescence method for quantitative analysis of sulfate and total sulfur in bottom sediments of watercourses and reservoirs located in the area of industrial enterprises impact. The quantitative determination of sulfur forms was carried out by analyzing the characteristic curves SKα1,2 and SKβ1,3, as well as the satellite line SKβ′ on X-ray emission spectra measured by an X-ray fluorescence spectrometer with wavelength dispersion. The study shows that these characteristic curves allow not only to determine the predominant form of sulfur, but also to separately conduct quantitative analyses of sulfates and total sulfur after fitting peaks and to separately analyze overlapping spectral lines. The results of quantitative analysis of the chemical state of sulfur by the proposed X-ray fluorescence method were compared with the results of inductively coupled plasma atomic emission spectroscopy and elemental analysis, as well as certified standard samples of soils and sediments. The results are in good agreement with each other.
-
Date submitted2024-05-02
-
Date accepted2024-06-03
-
Date published2024-07-04
Iron ore tailings as a raw material for Fe-Al coagulant production
The paper presents the results of experimental research into the recovery of Fe-Al coagulant from iron ore tailings (IOTs). The variables investigated in the laboratory tests included sulphuric acid concentration, temperature, leaching time, solid/liquid phase ratio (S:L) and the presence of stirring. The experiment determined the composition of the coagulant and the solid residue after leaching. The maximum iron content in the solution after leaching was obtained using 40 % H2SO4 at a temperature of 100 °C (or with stirring at 75 °C) and a contact time of 60 minutes. In this case, the iron yield was at the level of 25 % of the total content in the iron ore tailings. Chemical analysis of the solution obtained after leaching showed Fe and Al sulphate contents of 11 and 2 % respectively. In the next step, the efficiency of the coagulant was evaluated on model solutions of colour. The experimental results showed that the coagulant obtained from the iron ore tailings can be used for wastewater treatment in a wide pH range from 4 to 12 pH units. The solid residue after leaching is a fine-grained powder rich in silica, which can potentially be used as an artificial raw material in the construction industry. The research carried out in this thesis has shown that the extraction of coagulants from iron ore tailings can be considered as a way to extend the production chain of iron ore mining and to minimise the amount of tailings to be stored in tailing ponds. The technical solution presented in this work allows to comprehensively solve the problem of environmental protection by creating new target products for wastewater treatment from IOTs.
-
Date submitted2021-08-05
-
Date accepted2021-11-30
-
Date published2021-12-27
Morozkinskoye gold deposit (southern Yakutia): age and ore sources
The paper presents the results of the comprehensive isotope geochemical (Re-Os, Pb and δ 34 S) study of sulfide mineralization of the Morozkinskoye deposit. The ore zones of the deposit are localized in the syenite massif of Mount Rudnaya, which is located within the Central Aldan ore region (southern Yakutia). Gold mineralization is represented by vein-disseminated or vein type mineralization and is manifested in acidic low-temperature metasomatites – beresites (Qz-Ser-Ank-Py). For the first time we obtained an age estimate of the gold mineralization ~ 129 ± 3 Ma, which the synchronism of the hydrothermal ore process in the beresites, which formed the Morozkinskoye deposit, and magmatic crystallization of the syenites of Mount Rudnaya (~130 Ma). The osmium initial isotopic composition of the studied sulfides indicates a mixed mantle-crustal source of sulfide mineralization. New lead isotopic data of syenites indicate the predominance of mantle lead and an insignificant role of the lower – crust lead, while the isotopic composition of pyrite denotes the presence of the upper crustal material in the ore genesis. The sulfide δ 34 S values vary from –2.3 to +0.6 ‰ and indicate a predominantly magmatic source of sulfur in the ores.
-
Date submitted2021-05-31
-
Date accepted2021-10-18
-
Date published2021-12-16
Experimental evaluation of compressibility coefficients for fractures and intergranular pores of an oil and gas reservoir
- Authors:
- Vitaly S. Zhukov
- Yuri O. Kuzmin
The paper is devoted to studies of the volumetric response of rocks caused by changes in their stress state. Changes in the volume of fracture and intergranular components of the pore space based on measurements of the volume of pore fluid extruded from a rock sample with an increase in its all-round compression have been experimentally obtained and analyzed. Determination of the fracture and intergranular porosity components is based on the authors' earlier proposed method of their calculation using the values of longitudinal wave velocity and total porosity. The results of experimental and analytical studies of changes in porosity and its two components (intergranular and fractured) under the action of effective stresses are considered. This approach allowed the authors to estimate the magnitude of the range of changes in the volumetric compressibility of both intergranular pores and fractures in a representative collection of 37 samples of the Vendian-age sand reservoir of the Chayanda field. The method of separate estimation of the compressibility coefficients of fractures and intergranular pores is proposed, their values and dependence on the effective pressure are experimentally obtained. It is determined that the knowledge of the values of fracture and intergranular porosity volumetric compressibility will increase the reliability of estimates of changes in petrophysical parameters of oil and gas reservoirs caused by changes in the stress state during the development of hydrocarbon fields.
-
Date submitted2018-09-12
-
Date accepted2019-01-05
-
Date published2020-04-24
Flotation extraction of elemental sulfur from gold-bearing cakes
- Authors:
- Svetlana A. Ivanik
- Dmitrii A. Ilyukhin
Currently, in the development of the raw materials base of the gold mining industry, there is a tendency to reduce the quality of the initial mineral raw materials due to the depletion of reserves of rich gold-bearing ores. The article discusses the technology of extraction of refractory gold-bearing concentrates based on low-temperature leaching of pyrite concentrate. A decrease in the parameters of the autoclave oxidation of sulfide minerals, such as pyrite and arsenopyrite, leads to the incomplete extraction of gold into the solution and, consequently, its losses during subsequent cyanidation. As a possible option for a more complete extraction of gold using low-temperature oxidation technology, a method of flotation separation of elemental sulfur from leaching cakes is proposed. According to the basic process flow chart, the flotation process designed for gold extraction is carried out after autoclave oxidation, but before cyanidation. A series of experiments were carried out with varying reagent conditions and the dependence of gold losses on the extraction of elemental sulfur in the flotation tailings was established. As determining factors, pH and solid content in the initial pulp were considered. The paper justifies the separation of elemental sulfur from autoclave cake to enriched sulfur concentrate. The cake flotation modes after autoclave oxidative leaching of pyrite concentrate are investigated. The distribution of elemental sulfur and gold by flotation products makes it possible to conduct the tailings cyanidation process with acceptable indicators.
-
Date submitted2018-01-06
-
Date accepted2018-02-26
-
Date published2018-06-22
Extraction of platinum metals during procssing of chromium ores from dunnite deposits
- Authors:
- G. V. Petrov
- Ya. M. Shneerson
- Yu. V. Andreev
Currently, the main raw materials sources of platinum group metals in Russia are complex sulfide copper-nickel ores of the Taimyr region and placer deposits. However, in view of the inevitable loss of platinum metals during the metallurgical processing of initial ores and the deterioration of the quality of ore raw materials, along with a decrease in the share of platinum mining from placers, there is a need to look for new non-traditional sources of platinum group metals. Dunnites of the Middle Urals are promising platinum-bearing raw materials. The use of the gravitational-magnetic processing of chromium ores of dunnite deposits makes it possible to identify a magnetic platinum-bearing concentrate with a high content of magnetite and platinum-iron alloys, they can be refined using chemical-metallurgical methods. This article presents the results of research of identifying peculiarities of technological behavior of chromium, iron and noble metals during mechanical processing of ledge chromium ore. The kinetic regularities of the sulfuric acid decomposition of magnetite are determined. Optimum technological parameters of sulfuric acid leaching of iron from magnetic products of chromium ore dressing are established. Based on the conducted studies, the PDF and PID for the complex processing of chromium ores of dunnite deposits is proposed, which ensures the production of a rich platinum-bearing concentrate and a high-quality chromite concentrate that meets the requirements of chemical production.
-
Date submitted2015-10-05
-
Date accepted2015-12-14
-
Date published2016-08-22
Coal-peat compositions for co-combustion in local boilers
- Authors:
- A. V. Mikhailov
In article results of experiments on creation of coal and peat fuel compositions for burning in solid-fuel boilers are described. The main objective of research consisted in development of combination of coal dust and natural peat without binding additives. The role of peat consists that it increases efficiency of process of granulation, being natural binding. The method of granulation allows to utilize waste of the coal industry. Joint burning of two types of fuel – coal dust and peat reduces emission of sulfur dioxides. The cost of peat raw materials is lower, than artificial binding, applied to briquetting of coal dust. The composition of mix of coal dust and peat varied in the ratio 2:1, 1:1 and 1:2 in volume ratio at humidity of mix before extrusion of 65 %. In the course of preparatory operations of coal raw materials its crushing and sifting through sieve of 24 mesh (0,707 mm) was carried out. Procedure of hashing of samples of coal and peat was carried out before receiving homogeneous mixture. After hashing mix was located in piston press for receiving granules. Coal dust and wet peat pass semifixed extrusion on piston press with formation of cylindrical granules with a diameter of 16 mm. After extrusion of granule are dried to operational humidity of 25 %. Coal and peat fuel granules showed sufficient mechanical strength for transportation and power feed in solid-fuel boilers. Burning of coal and peat fuel granules in vitro at temperature of 800 °C does not lead to ashes agglomeration. The conducted preliminary researches showed prospects of utilization of coal waste by granulation method in mix with natural peat.
-
Date submitted2009-08-06
-
Date accepted2009-10-10
-
Date published2010-02-01
Allocation of tellurium from difficult on structure of sulfuric acid solutions
- Authors:
- S. B. Fokina
As the main source of reception of tellurium serve electrolytic copper refinery slimes. In the conditions of manufacture expansion and transition on technology decopperizing slimes by pressure leaching O 2 -H 2 SO 4 media, the solution (decopperized product) becomes the basic concentrator of tellurium. Extraction of tellurium from a decopperized (pressure-leached) liquid products is considered. The method allows to raise percent of extraction of tellurium from initial raw materials and to enrich pressure-leached solid product with precious metals.