-
Date submitted2022-10-29
-
Date accepted2023-10-25
-
Date published2024-04-25
Assessment of rock massif sustainability in the area of the underground research laboratory (Nizhnekanskii Massif, Enisei site)
The study presents the results of the research on geodynamic and geological conditions of the Enisei site (Krasnoyarsk Krai), chosen for the construction of an underground research laboratory. The laboratory is being built at a depth of 500 m to assess the suitability of the rock mass for burying high-level radioactive waste. The rocks consist of weakly fractured gneisses, granites, and dikes of metadolerites. Field observations were conducted on bedrock outcrops. They included the determination of rock mass quality indicators, measurement of rock fracturing, and a rating classification of stability using N.Barton's method. GNSS observations were also made to monitor surface deformations. These data were used to develop a three-dimensional structural model, including lithology, fault disruptions, intrusive bodies, elastic-strength properties of rocks, and the sizes of zones influenced by faulting. It will serve as a basis for boundary conditions and the construction of three-dimensional variational models of stress-strain states, identifying zones of concentration of hazardous stresses, and planning in situ geomechanical experiments in underground mines of the laboratory. The obtained values of the modified QR index for the main types of rocks allowed their classification as stable and moderately stable, corresponding to strong and very strong rocks on Barton's scale and the massif rating according to geomechanical classification.
-
Date submitted2022-06-20
-
Date accepted2023-01-10
-
Date published2023-08-28
Laboratory, numerical and field assessment of the effectiveness of cyclic geomechanical treatment on a tournaisian carbonate reservoir
Results are discussed for evaluation of effectiveness of the cyclic geomechanical treatment (CGT) on a Tournaisian carbonate reservoir. Analysis of laboratory experiments performed according to a special program to assess permeability changes for Tournaisian samples under cyclic changes in pore pressure is presented. The main conclusion is the positive selectivity of the CGT: an increase in permeability is observed for samples saturated with hydrocarbons (kerosene) with connate water, and maximal effect is related to the tightest samples. For water-saturated samples, the permeability decreases after the CGT. Thus, the CGT improves the drainage conditions for tight oil-saturated intervals. It is also confirmed that the CGT reduces the fracturing pressure in carbonate reservoirs. Using flow simulations on detailed sector models taking into account the results of laboratory experiments, a possible increase in well productivity index after CGT with different amplitudes of pressure variation was estimated. Results of a pilot CGT study on a well operating a Tournaisian carbonate reservoir are presented, including the interpretation of production logging and well testing. The increase in the well productivity index is estimated at 44-49 % for liquid and at 21-26 % for oil, with a more uniform inflow profile after the treatment. The results of the field experiment confirm the conclusions about the mechanisms and features of the CGT obtained from laboratory studies and flow simulations.
-
Date submitted2021-01-19
-
Date accepted2021-07-27
-
Date published2021-10-21
Geological and structural characteristics of deep-level rock mass of the Udachnaya pipe deposit
- Authors:
- Evgenii V. Serebryakov
- Andrei S. Gladkov
For hard rock massifs, structural disturbance is a key indicator of mining structure stability. The presence of intersecting structural elements in the massif reduces rock strength and leads to formation of potential collapse structures. In addition to that, disjunctive deformations that penetrate rock strata serve as channels for fluid migration and connect aquifers into a single system. It was established that the largest of them –faults of east-northeastern, northeastern and northwestern directions – form the kimberlite-bearing junction of the Udachnaya pipe. These faults represent zones of increased fracturing, brecciation and tectonic foliation, distinguished from adjacent areas by increased destruction of the rock mass. Specifics of tectonic fracture distribution within structural and lithological domains are determined by the presence of multidirectional prevailing systems of tectonic fracturing, as well as by differences in their quantitative characteristics. With some exceptions, the main systems form a diagonal network of fractures (northeastern – northwestern orientation), which is typical for larger structural forms – faults. Despite the differences in dip orientation of the systems, most of them correspond to identified directions, which is typical for both kimberlites and sedimentary strata. Overall disturbance of the massif, expressed in terms of elementary block volume, reaches its peak in the western ore body. For such type of deposits, friction properties of fracture structures have average values. Consideration of geological and structural data in the design and development of new levels of the deposit will allow to maintain the necessary balance between efficiency and safety of performed operations.
-
Date submitted2018-10-28
-
Date accepted2018-12-30
-
Date published2019-04-23
Development and research of formation technologies on specialized presses with subsequent sintering of high-density details from iron-based powders
- Authors:
- A. M. Dmitriev
- N. V. Korobov
- A. Zh. Badalyan
Creating shifts of the lyaers in a deforming workpieces improves the quality of the product produced by pressure treatment. qual-channel angular pressing and precipitations of a cylindrical billet with a rotating turnaround were developed by specialists earlier and became basic for scientists engaged in nanotechnology. One of the most modern schemes for creating nanostructures by processing on presses is the «Cyclic Extrusion Compression» scheme (in Russia – «Hourglass»), which has significant drawbacks. To date, research on the creation of layer shifts in compacted metal powders is substantially less than in compaction of compact blanks. The article developed compaction schemes for presses of blanks from iron-based powders that have a certain analogy with the «Hourglass», while lacking the disadvantages inherent in the named scheme and implemented on the created samples of specialized hydraulic presses. The results of the studies of density, strength and microhardness before sintering the samples molded from a number of domestic and imported powders on iron base, including those doped with carbon and other alloying components, are described. It has been established that with the use of the formation schemes for powders providing large shifts between particles, the density of the preforms increases on average by 10-12 %. With an average stress (16.32 MPa) of the transverse section of the molded specimen prior to its sintering, molding with shifts between particles increases this stress by 78 %. The strength after sintering of samples made using the compaction schemes developed by the authors of the article increases approximately by 2 times. Magnetic pulse treatment (MPT) of a molded sample prior to its sintering increases its resistance to shearing before sintering, regardless of the molding pattern. When MPT of both the powder and the molded sample is executed, the most uniform distribution of microhardness in the sample is achieved, and after subsequent sintering, the most uniform distribution of the mechanical characteristics of the product. The results of all studies are described by regression equations.
-
Date submitted2018-01-15
-
Date accepted2018-02-28
-
Date published2018-06-22
About the role of hydrafed calcium carboaluminates in improving the technology of complex processing of nephelines
- Authors:
- V. M. Sizyakov
- V. N. Brichkin
The scientific justification and development of the method for industrial synthesis of complex aluminates of alkaline earth metals is an innovative solution that determined several directions in the development of technology for complex processing of nepheline raw materials. It ensures the production of high-quality metallurgical alumina, the effective utilization of nepheline sludge and production of new types of multipurpose by-products. The modern development of these technical solutions is associated with ensuring the energy efficiency of the synthesis of hydrafed calcium carboaluminates (HCCA) and increasing the level of purification of aluminate solutions. The conditions for synthesizing HCCA with the use of calcareous materials of natural and technogenic origin have been experimentally determined, which makes it possible to isolate the average particle diameter as one of the determining factors of this process. The effect of the turnover of the hydrogarnet sludge on the removal of kinetic limitations in the process of deep desalination of aluminous solutions is theoretically justified. The conditions of a two-stage dosage of HCCA are experimentally determined. It is shown that the optimum ratio of the amount of the reagent supplied in the first and second stages is about 3: 2. At the same time, the maximum degree of precipitation of silica provides the production of aluminate solutions with a silicon module at the level of 95,000, which is achieved by using a HCCA synthesized based on chemically precipitated calcium carbonate in the processing of wastes from the production of mineral fertilizers.
-
Date submitted2018-01-14
-
Date accepted2018-03-12
-
Date published2018-06-22
Peculiarities of kinematics of rock mass shear during development of subseismic-scale faults
- Authors:
- A. V. Merzlikin
- L. N. Zakharova
The article describes the mechanism of formation and development of subseismic-scale faults in sedimentary rock mass based on results of physical and mathematical simulation. Physical modelling of layered rock massif was carried out by using sand-gypsum mixture. The results of physical modeling made it possible to visually evaluate the process of formation and development of subseismic-scale faults, to establish the orientation and amplitude of the modeled faults. It was established that faults with higher amplitude had filler material formed because of friction of fault edges/walls. The volume of modelled formation after formation of faults depending on fault amplitudes changed from 2-3 to 10 %. To gain information on stress deformed condition of rock massif and identification of key peculiarities of fault propagation dynamics we used the mathematical modeling based on particle-flow algorithm. The results of mathematical modeling determined that during formation of low amplitude faults the shear field has several rock clusters. Due to interaction of clusters, which have coordinated movement and promote massif loosening, the rock mass accumulates voids, which are the prerequisite for formation of subseismic-scale faults. The gained results enable to specify the complex mechanism of irreversible shears and deformations of rock mass during formation and development of subseismic-scale faults. It contributes to the improvement of the methodology for predicting the SSF parameters, which is of practical importance in terms of reducing mining risks.
-
Date submitted2016-09-16
-
Date accepted2016-11-12
-
Date published2017-02-22
Possibilities of seismic exploration for crystalline basement study
- Authors:
- A. N. Telegin
Possibilities of seismic methods of reflected and refracted waves have been examined for the purposes of detailed study on crystalline basement structure. Investigation of depth and structure of the basement plays an important role in the exploration of various deposits. Sedimentary cover is usually associated with oil and gas reserves. Ore deposits are formed in the basement rocks, basement splits and structure of its surface have a genetic relation not only to ore minerals, but also to oil resources. Reflection seismology is one of the main seismic methods of investigating structural geometry of the sedimentation mass, forecasting its material composition and possible hydrocarbon reserves. However, its possibilities for investigating crystalline basement are limited. Basing on many years’ experience of reflection seismology and physical modeling it has been identified that actual roughness of basement surface limits the obtainable amount of waves reflected from it. Possibilities of reflection seismology for basement structure study are mostly related to investigation of discontinuous faults as diffraction objects using diffracted waves. Method of refracted waves combined with modern procedures and material processing aimed at getting dynamic seismic sections holds much significance for the basement study, especially in the process of surface mapping and, to a lesser extent, in investigating discontinuous faults.
-
Date submitted2015-10-08
-
Date accepted2015-12-11
-
Date published2016-08-22
Rare metal granites in the structures of the Russian sector of Pacific ore belt
- Authors:
- V. I. Alekseev
Data are presented on the geology of areas of rare metal granites proliferation in the Russian sector of the Pacific Ore Belt that make one take a fresh look at the East Asian granitoid area to update its metallogeny. History is reviewed of studying rare metal granites of the Russian Far East. As a rule, these are found in the vicinity of major tungsten-stanniferous ore deposits, except much later than discovering the former, at the stages of their assessment and survey. Rare earth granites are usually missed by the geologists during the early stages of regional geological surveys due to their small size, weak eroding and external similarity with earlier granites. Using the examples of the Central Polousny, Badzhal and Kuyviveem-Pyrekakay regions the structural and geological conditions are characterized of localization of rare metal granites. Comparative analysis of geological situations made it possible to formulate the areal character of manifestation of rare metal granites; their confinedness to late Mesozoic orogenic arched uplifts of bogen structures above deep granitoid batholiths; positioning in the areas where longitudinal and transversal deep laying faults cross; gravitation to the environs of pre-Cambrian median masses.
-
Date submitted2014-12-09
-
Date accepted2015-02-16
-
Date published2015-12-25
Dynamic study of underground loading machine’s working tool crank-rocker mechanism
- Authors:
- I. P. Timofeev
- I. A. Korolev
The article is devoted to the dynamic study of the underground shovel’s working tool mech-anism, assembled in accordance with a crank-rocker scheme, containing curved wings, as well as to the study of the effect on uneven movement rate, produced by the working tool mechanism; pa-rameters and structural characteristics of the shovel paw design shape. On the basis of a synthesis of the loading machine’s working tool mechanisms, a kinematic scheme with a shovel paw, con-sisting of a straight operating part and a curved working tail, is offered. A dynamic model of the mechanism based on a variable weight of shovel bulk cargo and drive parameters of the working tool is developed, a motion equation is made up. Comparison between statistical indicators of effec-tive output obtained from the shovel loaders drive mechanism and the results of a separate computer simulation of the mechanisms under analysis attest to the proposed model’s performability.
-
Date submitted2014-07-02
-
Date accepted2014-08-24
-
Date published2014-12-22
Informational support for prompt project management of microfault exploration
- Authors:
- V. V. Nazimko
Geologic, technological, psychological, economic and organizational uncertainty impede extraction from coal seams that are corrupted by microfaults. We propose the exploration and extraction from the corrupted coal seams in a project management mode.
-
Date submitted2009-10-18
-
Date accepted2009-12-05
-
Date published2010-09-22
Assessment of the role of geodynamic factor in the accident rate of pipeline systems
- Authors:
- E. K. Melnikov
- A. N. Shabarov
The authors relate to the geodynamically active faults those faults with continuous up to present time low-amplitude movements which lead to the destructurization both of bedding rocks and of Quarternary deposits. The electrogeochemical processes proceeding in the zones of such faults, promote the metal corrosion that basically is the cause of increasing a few tens of times of specific accident rate at sites of active faults crossing with pipelines.
-
Date submitted2009-10-21
-
Date accepted2009-12-05
-
Date published2010-09-22
Ecologycal and geodynamic safety and problems in industrial ecological monitoring at objects of an oil-gas complex
- Authors:
- A. I. Nikonov
- O. V. Luk"yanov
This article is focused on the influence of modern geodynamics on landscape and its structure. Modern geodynamical processes manifest in anomalous rock deforming in the fault zones. Their natural or technogenic activation causes the appearance of dangerous geological processes. It can be taken into account only by geodynamical monitoring on the objects of oil and gas industry.
-
Date submitted2009-10-13
-
Date accepted2009-12-14
-
Date published2010-09-22
The evaluation of geodynamic consequences оf long-term exploration of lower cretaceous sediments at the Yamburg oil-gas condensate field with join of additional wells
Within the framework of the engineering design of the join up of additional wells of Lower Cretaceous sediments at the Yamburg oil-gas condensate field the evaluation of geodynamic consequences of long-term exploitation of the mentioned field was performed, as well as the hazardous geodynamic process permanent survey program was developed.
-
Date submitted2009-10-20
-
Date accepted2009-12-25
-
Date published2010-09-22
Scientific-methodical foundation for geodynamic safety of oil and gas objects
- Authors:
- Yu. O. Kuzmin
It was shown on example of a number of deposits that space contemporaneity of emergency situations at wells and pipeline systems to fault zones finds its natural explanation within the concepts of existence of SD processes in such zones. In such situation it is essential to conduct very thoughtful system of diagnostics of crust fields with fluctuation deformation characteristics. For that purpose follow-up realization of three interconnected procedures must be conducted: detailed and measurement-assured monitoring (geodynamic test-area), complex several-variant interpretation of results of the monitoring and selection of different scenarios of possible negative contour, determination of the level of geodynamic risk, forecasting the environmental, social and economic consequences, and formulating strategies for preventive arrangements.
-
Date submitted2009-10-12
-
Date accepted2009-12-29
-
Date published2010-09-22
Types and mechanisms of geodynamic hazard in mineral deposits mining and exploitation of buried and surface engineer constructions
- Authors:
- A. N. Shabarov
It is shown that major emergencies in mineral deposits mining and in exploitation of buried and surface engineer constructions are attributed to active faults. Classification of hazardous zones has been developed. The mechanisms of influence of geodynamic hazard in coal mines and pipeline exploitation were determined. The technology of reduction of geodynamic risk was suggested.
-
Date submitted2009-08-17
-
Date accepted2009-10-18
-
Date published2010-02-01
Geotechnical engineering and hydrogeological specifics of estimate high-rise buildings construction and operation conditions (in terms of local zone on the right bank of Neva river)
- Authors:
- A. M. Zhukova
In the paper specificity of geotechnical engineering conditions in the local zone of the right river Neva bank are considered. The influence of underground topographies of Pre-Quaternary soils roof formed by paleovalleys on the specificity of engineering geological profile is analyzed. Influence of tectonic faults on physical and mechanical properties of Upper Kotlin clays (Upper Vendian) which it is planned to use as the basis for high-rise constructions is considered. Negative influence of Low Kotlin (Upper Vendian) pressure water-bearing horizon on clay properties in the construction foundation and structural materials is investigated.
-
Date submitted2009-07-16
-
Date accepted2009-09-10
-
Date published2010-04-22
Influence of tectonic stresses and geological disturbances in rock mass on the parameters of stress-strain state around mine workings
- Authors:
- D. N. Petrov
- I. S. Dolgy
- V. I. Ochkurov
The results of mathematical modeling of formation of stress fields in stratified rock mass under various vertical and horizontal stresses relation are presented. An assessment of influence of the presence and position of a great geological disturbance on a stress state around a mine working is considered.
-
Date submitted2009-07-29
-
Date accepted2009-09-29
-
Date published2010-04-22
State examination of mineral reserves in the system of wise utilization of the earth’s interior
- Authors:
- Yu. A. Podturkin
The major problem of bodies of the government in sphere of regulation of attitudes protection of reserves creation of conditions for rational use of resources. The basic role in its decision is played with examination protection of reserves. Maintenance of effective carrying out of examination demands its constant perfection with reference to market conditions with use of the international criteria regarding both calculation and an estimation of stocks, and drawing up design and the engineering specifications on development of mineral deposits.
-
Date submitted2009-07-27
-
Date accepted2009-09-30
-
Date published2010-04-22
Results of repeated geodetic observations аt the Мukhanovsk technogenic geodynamic polygon
Results of repeated leveling observations on the geodynamic range, organised on the Muhanovsky oil field (Samara region) are presented. It is shown that the most abnormal vertical displacement of a terrestrial surface (120 mm) are dated to fault to a zone located in the western part of the field and represent an essential danger to objects of the infrastructure of an oil field. Vertical displacement along the profile crossing Otradny town, located at oil field, are insignificant and it makes value of 2 to3 mm.
-
Date submitted2008-10-15
-
Date accepted2008-12-05
-
Date published2009-12-11
Prospects of nickel industry in the Urals in the light of ore field structure study in supergene nickel deposits
Tectonic fractures of meridian spread, masked by block system of neotectonic breaks, play the leading role in structural control of nickel mineralization in supergene nickel deposits in the Urals. The deposits have long-term genesis and polygenic character. They are characterized by intensive tectonic and hydrothermal workup of Paleozoic substrate and block structure with small amplitude of vertical displacement. All of them have a two-floor structure, where upper supergene floor has a «background» of lower hydrothermal floor. This fact considerably increases the field of geological prospecting and searching of new oxide-silicate nickel deposits in the Uralian region.
-
Date submitted2008-10-24
-
Date accepted2008-12-06
-
Date published2009-12-11
Geological structure, characteristics of ores and genesis of ore occurrences in the Halvdanpiggen field (West Spitsbergen island)
- Authors:
- A. N. Sirotkin
- V. V. Khailov
- D. V. Nikitin
A new metallogenic zone was separated out in a central part of the archipelago Spitsbergen by the results of exploration work. It was shown an integral series of ore areas and fields in the limits of this zone, including the ore field Halvdanpiggen. This field integrates several non-uniformly scaled the ore occurrences, which present a great interest in regard to a material composition of the ore. They likewise produce an information for determination of genesis and outlooks of total metallogenic zone. The article contains data on geology, mineralogy and geochemistry of deposits; it is established their genesis, formation membership and time of origination.