-
Date submitted2024-05-15
-
Date accepted2025-01-28
-
Date published2025-04-30
Study of changes in the void space of core samples under cyclic loading
The subsurface state is explored and analysed by studying the core material. This is the basis for forecasts, construction and improvement of models. The reservoir properties of rocks obtained from the laboratory study of sample are subject to a system error caused by three main factors: rock selection in the zone of altered stress-strain state, rock removal from the thermobaric conditions of natural occurrence, and the measuring equipment error. A change in the natural stress-strain state of rocks occurs as a result of intervention in the formation system and the entire massif by constructing a well, creating overburden and depression. The rise of the core causes unloading from formation pressure to atmospheric one, natural saturation is lost, temperature conditions change. This affects the reservoir properties and rock injectivity. This study is aimed at investigating changes in the void space of the rock in formation conditions under cyclic loading. Based on the data obtained, a regression forecast of properties is made, excluding external influences. The article describes the results of experiments on multiple loading and unloading of water-saturated sandstone samples by geostatic pressure with precise control of the water displaced and returned to the void space. This method enables us to record the change in the internal void volume of the rock and, as a consequence, elastic and plastic deformations, the value of relaxation of elastic deformations. The dynamics of change in the coefficients of porosity and compressibility from the stress state cycle is estimated and the range of predicted porosity values of the rock in formation conditions is determined. For samples of permeable medium- to fine-grained sandstone, the obtained character of porosity change gives a forecast of the initial porosity in formation conditions of 20.19±0.61 %. Thus, the exclusion of human impact on porosity gives values 1.42 % higher than the results of standard laboratory studies.
-
Date submitted2024-04-22
-
Date accepted2024-06-13
-
Date published2024-07-04
Lithification of leachate from municipal solid waste landfills with blast furnace slag
- Authors:
- Mariya A. Pashkevich
- Yuliya A. Kulikova
The article presents an alternative method of utilization of blast furnace slag and leachate from solid municipal waste landfills, the formation of which occurs during the infiltration of atmospheric precipitation through the thickness of deposited waste. The method is based on the conversion of leachate from the liquid phase to the solid aggregate state by lithification using blast furnace slag as an astringent material. The hydraulic activity of slag, which depends on the amount of oxides contained in it, has been estimated. The investigated slag belongs to the 3rd grade, which confirms the possibility of its use as an astringent material. The filtrate was analyzed for the content of various elements, and the maximum permissible concentrations for each element were found to be exceeded. Chemical and biological oxygen demand were determined, and critically high values were installed (17200 mgO2/l and 4750 mgO2/l, respectively). The lithification process was divided into two stages. The first stage was to reduce the organic component in the filtrate using a coagulant, aluminum sulfate; the second stage was slag hydration. The optimum ratio of lithificate components in terms of mixture solidification rate was established at 1:0.03:1.25 (leachate, coagulant, blast furnace slag). The obtained material was analyzed for the solubility and content of various forms of metal. It is established that at infiltration of atmospheric precipitations through lithificate only 3 % of material will be washed out; concentrations of gross and mobile forms of heavy metals do not exceed the maximum permissible, except for the gross content of arsenic, mobile, and water-soluble forms of which were not found. The values of chemical (687 mgO2/l) and biological (173 mgO2/l) oxygen demand in the aqueous extract from lithificate decreased more than 25 times in comparison with the initial filtrate. According to the results of toxicological studies, lithificate was assigned an IV class of waste hazard, which confirms the possibility of its use as bulk material at landfills.
-
Date submitted2022-05-12
-
Date accepted2022-09-15
-
Date published2022-12-29
Problem solution analysis on finding the velocity distribution for laminar flow of a non-linear viscous flushing fluid in the annular space of a well
- Authors:
- Vasiliy I. Nikitin
Modern drilling fluids are non-linear viscous media with an initial shear stress. In classical scientific works on hydromechanical modeling of drilling fluids motion in pipes and annular channels the Shvedov – Bingham approximation and Ostwald – de Waale power-law model were used, which did not fully account for behavior of technological fluids in a wide range of shear rates. This article presents a numerical solution for a mathematical model of drilling fluid motion of the three-parameter Herschel – Bulkley rheological model in the annular space of the well. The Herschel – Bulkley model in the rheological equation takes into account the presence of initial shear stress and a tendency for viscosity to change with shear rate, which distinguishes it from the Ostwald – de Waale and Shvedov – Bingham models. The target function in solving the equation of motion is the velocity distribution in the radial direction of the upward flow of the flushing fluid. The analysis of obtained solution is based on the theory of velocity profile influence on quality of cuttings removal during wellbore cleaning. Due to peculiarities of mathematical statement of the task, which supposes necessity of differential equation of motion solution, Wolfram Mathematica computational software has been used as a calculation tool. The analysis of numerical solution allowed to draw conclusions about the possibility of its application in evaluation of velocity profile when drilling fluid moves in annular space of the well. The possibility for application of modified excess coefficient as a relative quantitative parameter for evaluation of velocity profile uniformity was substantiated.
-
Date submitted2021-09-01
-
Date accepted2022-10-07
-
Date published2022-12-29
Parameter determination of the method of directional unloading of the reservoir based on physical modelling on a true triaxial loading setup
The article presents a theoretical and experimental substantiation of the method of directional unloading of the reservoir in fields with low-permeability reservoirs. The relevance of the article is due to the reduction of hydrocarbon resources in modern conditions and the need to create new efficient environmentally friendly technologies to develop hydrocarbon deposits with hard-to-recover reserves, primarily with low-permeability reservoirs. The results of a theoretical study of the stress-strain state in the vicinity of a well, both cased and open, are presented. They are necessary to develop programs for laboratory testing of core specimens from the studied fields. A technique for physical modelling of deformation processes in the bottomhole zone with a decrease in pressure at the well bottom in a true triaxial loading unit is described in order to determine the parameters of the process impact on the formation reservoir, leading to an increase in well productivity. The method was applied to the conditions of the low-permeability reservoir at the Verkhneviluchanskoye oil and gas condensate field in the southwest of the Republic of Sakha (Yakutia). Expe-rimental studies were carried out on a unique scientific unit for true triaxial loading, created at the IPMech RAS, the Triaxial Independent Loading Test System. The directional unloading method was adapted for the studied field, the process parameters of successful application of the method were determined: the bottomhole design, the drawdown values necessary to increase the permeability of the bottomhole formation zone.
-
Date submitted2019-07-22
-
Date accepted2020-01-04
-
Date published2020-04-24
“Ural-20R” combines loading drives evaluation in two-stage development of the face
The technological features of the use of high-performance Ural-20R combines in the conditions of potash mines in Russia are described. It is shown that when the capacity of the worked potash seams is over 4 m, a two-layer ore extraction is used. The formation of cutting process, implemented by the second course of the combine in the treatment chamber, is carried out by an incomplete section of the executive bodies. The standard control system, display and protection of the Ural-20R combine does not allow monitoring and reliable estimation of the magnitude of dynamic components on the drives of the mining machine loads, as well as tracking the feed rate of the combine to the face. The regulation of the operating parameters and the assessment of the degree of loading of the drives of the excavating machine in real time are assigned to the operator. The fundamentals of the experimental research methodology for assessing the loading of drives of Ural-20R combines with the destruction of the potash mass by an incomplete section of the executive bodies are described. The device and the operating procedure of the “Vatur” software-recording complex, which measures, records and records the electrical parameters of the drive motors of a mining machine, is described. The process studies results of forming loads on drive elements of Ural-20R combines when mining a face with an incomplete section of executive bodies are presented. It is proved that the work of combine harvesters on the undercut of the formation with a high feed rate is accompanied by significant dynamic loads on the drives of planetary organs and an overload of the drives of the Berm organs, which leads to an accelerated consumption of the resource and emergency failures of the gearboxes and motors of the extraction machine.
-
Date submitted2019-07-21
-
Date accepted2019-09-20
-
Date published2020-02-25
Assessment of operational reliability of quarry excavator-dump truck complexes
- Authors:
- V. M. Kurganov
- M. V. Gryaznov
- S. V. Kolobanov
The method proposed in the article is based on the mathematical apparatus for quantitative assessment of the reliability of majority schemes of structural redundancy of transport processes, which provide the availability and usage of several backup delivery channels in the transport process in case of any malfunction. The principle of multi-channel haulage is commonly used in quarries for transportation of overburden and minerals from benches by dump trucks, when excavators and dump trucks performing cyclic operations function as a single excavator-dump truck complex. This pattern of work significantly increases the likelihood of fulfilling the daily plan for transporting rock mass due to the redistribution of dump trucks between mining and overburden excavators in the event of failure of one or more units of mining and handling equipment. The reliability of excavator-dump truck complexes is assessed in three stages: initial data collection for mathematical modeling of excavator-dump truck complex performance; solving the problem of optimizing the distribution of dump trucks between excavators, ensuring maximum productivity of the excavator-dump truck complex; assessment of the reliability of its work depending on the probability of fulfilling the daily plan for the transportation of rock mass. The proposed method is implemented as part of a computer program and makes it possible to automate the operational management of the process of transporting rock mass in a quarry using a mobile application. The developed guidelines can be used for any quarries with automobile transport, regardless of the type of mineral extracted, the mining method, the loading pattern, the capacity of the excavation and loading equipment fleet, and the capacity of operated dump trucks.
-
Date submitted2019-05-05
-
Date accepted2019-07-03
-
Date published2019-10-23
Scraper Face Conveyors Dynamic Load Control
- Authors:
- E. K. Eshchin
The task of controlling the dynamic loading of scraper face conveyors (SC) is considered and the unsatisfactory state of loading of mechanical and electrical components of the SC is recorded. The possibility of the appearance of a self-oscillatory nature of the entire system load due to the peculiarities of the movement of the traction chain along the lattice frame of the SC is indicated. The property of the system is noted – the cyclic nature of the loading of the circuit during movement, which causes energy exchange processes between the mechanical and electromotive components of the conveyor (when using the head and tail electric drives) through the common cable network of the power supply system of the SC. A high level of dynamic loading of the electromechanical system causes the problem of eliminating the self-oscillating operating mode of the SC that generates it which is proposed to be solved by changing the angular rotation speeds of the SC drive sprockets. Angular speeds can be changed by applying frequency control of asynchronous electric motors. The efficiency of setting the frequency of electric motor stator currents of the head and tail drives of the conveyor is established in proportion to the frequency of rotors rotation to eliminate self- oscillating modes of operation in the main operating mode. The possibility of reducing the starting shock values of the electromagnetic moments of electric motors is considered. The results of the calculation of the start-up and liquidation of the self-oscillating operating mode are presented on the example of the scraper face conveyor Anzhera-34. The results of calculations of the start-up modes and the main operational transportation of coal in an uncontrolled mode of operation and after the introduction of control are compared, based on which it is concluded that it is advisable to use active control of the dynamic loading ofSC.
-
Date submitted2019-04-30
-
Date accepted2019-07-16
-
Date published2019-10-23
Salt Rock Deformation under Bulk Multiple-Stage Loading
- Authors:
- I. L. Pankov
- I. A. Morozov
The paper presents experimental justification of the possibility to use bulk multiple-stage loading to study the process of salt rock deformation in the laboratory conditions. Results of comparative tests between bulk multiple- stage and single-stage loading of salt rock samples are demonstrated. The paper contains results of research on the rate of lateral pressure and its impact on strength limit and residual strength limit of sylvinite, estimated using single- stage and multiple-stage methods. Research results demonstrate how the rate of lateral pressure impacts dilatancy boundary of salt rocks. Analysis of how the loading method influences certificate parameters of Mohr-Coulomb strength of sylvinite has been carried out. The dynamics of elastic modulus in the process of salt rock deformation is analyzed depending on the rate of lateralpressure. It is demonstrated how the method of multiple-stage loading adequately reflects the processes of salt rock de- formation and decomposition, and facilitates not only lowering impact of sample’s inner structure heterogeneities on the experimental results, but also significant reduction in the required amount of rock material.
-
Date submitted2019-03-19
-
Date accepted2019-05-22
-
Date published2019-08-23
Engineering of Complex Structure Apatite Deposits and Excavating-Sorting Equipment for Its Implementation
- Authors:
- A. Yu. Cheban
Development of Oshurkovskoye apatite deposit with conventional methods, using drilling, blasting and then processing of extracted ore by means of flotation and construction of hydraulic structures to store wet tailings, turns out to be impossible, as the reservoir is located in a special ecological zone of Transbaikal; moreover, the deposit has a complex geological structure and a low grade of valuable component in the orebody. Refinement of the mineral product occurs primarily during its processing; however, ore grade can already be controlled in the process of its extraction. Advancement of technical facilities opens up new opportunities of selective mining for complex structure deposits. The purpose of this research is to create a technology, which will upgrade the quality of mineral substance, fed to the processing plant, directly at the extraction stage. The paper proposes a technological development scheme for Oshurkovskoye deposit using an excavating-sorting complex containing a transport-sorting facility and a measuring unit for estimation of the grade in a milled rock mass; it allows to separate a rich fine fraction of substandard ore, which under conventional mining practices would have been sent to the stockpile of temporarily substandard ore. Separation of fine fractions of apatite ore in the transport-sorting facility allows to reduce dusting during production and cuts the losses of valuable component, associated with aeration of fine fractions during loading and transportation of the rock mass. Positioning of oversize material in the open trench with its subsequent selective extraction by the loading machine facilitates non-stop operation of the mining-sorting equipment, which provides an increase in the productivity of mining operations.
-
Date submitted2018-12-25
-
Date accepted2019-03-08
-
Date published2019-06-25
Determination of the operating time and residual life of self-propelled mine cars of potassium mines on the basis of integrated monitoring data
Statistical data on the reliability of self-propelled mine cars (SPMC), operating in the potassium mines of the Verkhnekamskoye potassium and magnesium salts deposit are analyzed. Identified the main nodes that limit the resource SPMC. It has been proven that the most common failures of self-propelled cars are the failure of wheel hubs, bevel gears and traveling electric motors. The analysis of the system of maintenance and repair of mine self-propelled cars. It is indicated that the planning and preventive system of SPMC repairs is characterized by low efficiency and high material costs: car maintenance is often carried out upon the occurrence of a failure, which leads to prolonged downtime not only of a specific haul truck, but of the entire mining complex. A method for assessing the technical condition of the electromechanical part of a mine self-propelled car by the nature of power consumption is proposed. This method allows you to control the loading of the drives of the mine self-propelled car, as well as to assess the technical condition of the drives of the delivery machines in real time. Upon expiration of the standard service life of a mine propelled car specified in the operational documentation, its further operation is prohibited and the car is subject to industrial safety expertise. As part of the examination, it is necessary to determine the operating time and calculate the service life of a mine self-propelled car outside the regulatory period. A method has been developed for determining the residual service life of mine car on the basis of instrumentation control data in the conditions of potash mines.
-
Date submitted2018-07-04
-
Date accepted2018-09-17
-
Date published2018-12-21
Secondary dispersion halos as a prospecting indicator of platinum metal mineralization on the example of the Kamenushinsky massif (Middle Urals)
- Authors:
- A. M. Minibaev
The paper discusses the results of bulk rock geochemical sampling of the Kamenushinsky massif eluvial-deluvial deposits and the massifs bedrocks spectral analysis data. Evaluation of secondary dispersion halos using two-dimensional modeling and multivariate statistic processing of the results have allowed establishing the spatial collocation of platinum and chromium anomalies and high correlation between these elements. These facts confirm the considerable contribution of chromite-platinum mineralization to the primary ores of the entire Kamenushinsky massif. The geological observations and rocks chemical composition analysis has revealed that uranium and barium anomalies are associated with the areas of gabbro and granitoids dike bodies. The insignificant overlapping of uranium and barium anomalies with platinum and chromium ones, as well as the negative correlation between these two groups of elements, is inconsistent with earlier conclusions on the spatial association of platinum mineralization with gabbro and granitoids dikes and a possible connection between these dikes and platinum metal mineralization zones.
-
Date submitted2014-12-30
-
Date accepted2015-02-03
-
Date published2015-12-25
Open mining technique for unconventional mineral deposits
- Authors:
- G. A. Kholodnyakov
- K. R. Argimbaev
Nowadays the majority of deposits are successfully exploiting by mining enterprises with the help of traditional excavation and loading equipment. Typically, metals, construction materials, etc. are mined and extracted on these deposits, but modern society is progressing and producing new requirements to metals properties for creating a new type of equipment. The metals with new properties are located in unconventional areas: either in technogenic deposits (overburden dumps, tailings, etc.) or in hard-to-get natural formations. Technogenic mines, being a tailing of Kachkanarsky mining and processing plant, are referred to such unique deposits, which have expensive metals (scandium, gallium, strontium, titanium), as well as the natural deposit – rhenium deposit, located in the crater of an active volcano. Potentialities of open mining in the largest rhenium deposit with complex environmental occurrence have been analyzed in the paper. Temperature measurement results of adjacent strata and a temperature scheme of the host rocks on a separate site and the entire field have been presented. An open mining technique for a primary mining area as well as perspective methods of rock preparation for excavation, applicable to this particular deposit, has been considered.
-
Date submitted2014-12-09
-
Date accepted2015-02-16
-
Date published2015-12-25
Dynamic study of underground loading machine’s working tool crank-rocker mechanism
- Authors:
- I. P. Timofeev
- I. A. Korolev
The article is devoted to the dynamic study of the underground shovel’s working tool mech-anism, assembled in accordance with a crank-rocker scheme, containing curved wings, as well as to the study of the effect on uneven movement rate, produced by the working tool mechanism; pa-rameters and structural characteristics of the shovel paw design shape. On the basis of a synthesis of the loading machine’s working tool mechanisms, a kinematic scheme with a shovel paw, con-sisting of a straight operating part and a curved working tail, is offered. A dynamic model of the mechanism based on a variable weight of shovel bulk cargo and drive parameters of the working tool is developed, a motion equation is made up. Comparison between statistical indicators of effec-tive output obtained from the shovel loaders drive mechanism and the results of a separate computer simulation of the mechanisms under analysis attest to the proposed model’s performability.
-
Date submitted2013-07-10
-
Date accepted2013-09-14
-
Date published2014-03-17
Quality management of brown coal at open-pit mine in the presence of several consumers with varios requirements to it
- Authors:
- M. M. Yakubovskii
- K. Drebenshtedt
The article considers main stages of mine planning and modern methods of quality management at open-pit coal mines in Germany. The object of research is the company «MIBRAG GmbH» producing brown coal and providing them a wide range of consumers which have dif-ferent demands to the coal’s quality.
-
Date submitted2010-07-14
-
Date accepted2010-09-07
-
Date published2011-03-21
Substantiation of pumped volumes of flow angularity compositions in injection wells
- Authors:
- A. R. Mavliev
- M. K. Rogachev
- D. V. Mardashov
The method of calculation pumped volumes of flow angularity compositions in injection wells, which based on combination of the seepage theory, laboratory investigation and field experience is developed.
-
Date submitted2010-07-10
-
Date accepted2010-09-15
-
Date published2011-03-21
Reduction methods of high harmonics influence on the electric equipment operation
- Authors:
- Ya. E. Shklyarsky
- A. N. Skamin
This work contains brief analysis of high harmonics reduction methods. It is offered to make a choice between reduction methods of high harmonics influence on condenser batteries depending on factors of harmonics occurrence. Definition algorithm for the most effective method of high harmonics reduction on condenser batteries operation is created.
-
Date submitted2010-07-29
-
Date accepted2010-09-27
-
Date published2011-03-21
Efficiency increasing of condenser batteries operation in mining enterprise`s electric circuits
- Authors:
- A. N. Skamin
This work contains the method of effective reactive power compensation at the expense of high harmonics reduction. The decrease of condenser batteries overloading from the high harmonics is based on variation of condenser power depending on current and voltage spectral structure, electric network parameters and load power.
-
Date submitted2009-09-19
-
Date accepted2009-11-15
-
Date published2010-06-25
Potassium chloride content in ore and products оf recycling automatic control system
- Authors:
- S. S. Galushkin
- B. A. Vishnyak
- V. N. Smirnov
Potassium chloride percentage in continuous transported ore flows and products of potassium plants recycling automatic control system is offered and described. It differs fundamentally from used before ones at bulk solids containing natural radio-activity elements effective constituents producing and recycling plants. Sensing device is used in this information-measuring system (IMS). It allows to realize automatic control in flows for that instantaneous productivity fluidity in wide limits is resided. Using such IMS gives considerable economic effect by measurements error lowering and their quickness increase.
-
Date submitted2009-09-26
-
Date accepted2009-11-14
-
Date published2010-06-25
Automatic bulk solids moisture in stream control system
- Authors:
- S. S. Galushkin
- B. A. Vishniak
- V. N. Smirnov
Automatic moisture in fine-dyspersated stream control system based on microwave frequency method is presented. Minimizing means of interrupting factors peculiar to this method of measurement are produced and systematically proved.
-
Date submitted2009-08-28
-
Date accepted2009-10-04
-
Date published2010-02-01
The integrated reloading point at the combined auto-railway transportation
- Authors:
- M. M. Yakubovskii
- G. A. Kholodniakov
In article it is considered the technology of creation and exploitation of reloading ore warehouse. As the reloading equipment it is offered to use a hydraulic backhoe excavator. At the combined transport the warehouse is an irreplaceable link in a technological chain. Basic difference from existing schemes of warehousing is that ore is housed not in a stack but in a concentration trench. The concentration trench is formed in immediate proximity from a face. It allows to prolong the operation term of the warehouse and to exclude rigid interdependence of the combined transport links.
-
Date submitted2008-10-16
-
Date accepted2008-12-10
-
Date published2009-12-11
Collecting properties of rocks in changes оf stress state type
- Authors:
- A. T. Karmansky
The article presents the results of investigations of the influence of stress state form, cyclic loading and time of bearing specimens under loads on the pattern of changes in porosity and permeability. It was stated that compressibility of rocks is proportional to porosity, and with rise of applied stress the compressibility decreases exponentially.