-
Date submitted2022-11-11
-
Date accepted2023-01-19
-
Date published2023-12-25
Evaluation of the efficiency of sorbents for accidental oil spill response in the Arctic waters
The development and operation of new oil fields on the Arctic shelf increases the risks of oil spills, which require the use of oil spill response tools and materials that are efficient in harsh climatic conditions. The question of actual efficiency of sorbents for reducing the level of oil pollution in the conditions of the Arctic and subarctic waters is relevant. The work is aimed at a comparative study of the efficiency of sorbents of mineral and organic origin used by coastal enterprises in the Kola Bay as well as a sorbent based on chitin in model systems simulating real conditions in sea waters. The characteristics of sorption agents were determined applying ASTM F716-18 procedure. Sorption capacity was evaluated in respect of ARCO grade oil, diesel fuel and marine oil. The efficiency of sorbents was estimated in model systems “sea water – oil” at water temperature corresponding to the average annual surface temperature in the Barents Sea. Actual data on sorption capacity of commercial sorbents “Lessorb”, “Novosorb”, a sorbent based on vermiculite and chitin sorbent in relation to potential pollutants of waters were obtained. The dynamics of sea water saturation with oil products at –0.5 (±1) and 10 (±1) °С was determined. It is shown that at higher temperature the concentration of oil products in sea water column (in the presence of an oil film on the surface) is on average four times higher than at low temperature. Kinetic dependences were obtained that describe the content of oil products in water column and near-surface layer of sea water in the presence of the studied sorbents at 5 (±1) °C, corresponding to the average annual temperature in the Kola Bay of the Barents Sea. A method is proposed for evaluating the efficiency of sorbents from the values of regression coefficients characterizing the dependence of oil products content in sea water on the character of sorbent and duration of its action.
-
Date submitted2022-06-01
-
Date accepted2022-09-06
-
Date published2022-11-10
Impact of EU carbon border adjustment mechanism on the economic efficiency of Russian oil refining
- Authors:
- Vladimir L. Ulanov
- Oleg N. Skorobogatko
The carbon border adjustment mechanism (CBAM) leads not only to the expected environmental changes, but also to the transformation of market environment. The study estimates the losses of the oil refining sector from the introduction of CBAM for the export of oil products from Russia to the countries of the European Union. An approach to assess the impact of CBAM on the cost of oil products has been formed and the mechanisms of its impact on the economy of Russian oil refineries have been identified. The study was carried out on the basis of actual data on the volume of greenhouse gas emissions in accordance with the current rules of the European emissions trading system. Decomposition of assessments of the CBAM impact was carried out into direct and indirect effects, as well as the effect of adaptation. It is shown that with the introduction of the CBAM mechanism, the prices of oil products in the domestic market will be determined not only by the logistical factor, but also by the requirements for environmental friendliness of oil refining. The introduction of CBAM will have a significant impact on the economics of oil refining, including refineries that do not export to the EU. The total impact of CBAM on the economy of Russian oil refineries will be about 250 mln dollars.
-
Date submitted2021-10-08
-
Date accepted2022-01-24
-
Date published2022-04-29
Methodology for thermal desorption treatment of local soil pollution by oil products at the facilities of the mineral resource industry
- Authors:
- Mariya A. Pashkevich
- Marina V. Bykova
The analysis of the main environmental consequences of leaks and local spills of petroleum products at the enterprises of the mineral resource complex is presented. It is established that the problem of soil contamination with petroleum products at the facilities of the mineral resource complex and enterprises of other industries is caused by significant volumes of consumption of the main types of oil products. Based on the results of the author's previous field research, a series of experiments was carried out, consisting in modeling artificial soil pollution with petroleum products such as gasoline, diesel fuel, highly refined oil, motor oil, and transmission oil, followed by their purification by heat treatment at temperatures of 150, 200, and 250 °C. The 250 °C limit of the heating temperature was set due to the need to partially preserve the structure and quality of the soil after heat treatment to preserve its fertility. When the processing temperature rises to 450 °C, all humates are completely burned out and, as a result, productivity is lost. Confirmation is provided by the results of experiments to determine the humus content in uncontaminated soil and soil treated at different temperatures. It was found that at a maximum processing temperature of 250 °C, about 50 % of the initial organic carbon content is preserved. According to the results of the conducted experimental studies, the dependences of the required processing temperature on the concentration of petroleum products to reduce the concentration of petroleum products to an acceptable level have been established. The methodology of thermal desorption cleaning of soils with varying degrees of contamination at enterprises of the mineral resource complex is presented.
-
Date submitted2021-04-26
-
Date accepted2021-07-27
-
Date published2021-10-21
Study of the dynamics for gas accumulation in the annulus of production wells
Accumulation of associated petroleum gas in the annulus is one of the negative factors that impede the intensification of mechanized oil production. An increase in annular gas pressure causes growth of bottomhole pressure, a decrease in back pressure to the formation and the inflow of formation fluid. In addition, accumulation of gas in the annulus leads to displacement and a decrease in the liquid level above the submersible pump. Insufficient level of the pump submersion (rod or electric submersible) causes a number of complications in the operation of mechanized production units associated with overheating of the elements in pumping units. Therefore, the development of technologies for optimizing the gas pressure in the annulus is relevant. Method for calculating the intensity of gas pressure increase in the annulus of production wells operated by submersible pumps has been developed. Analytical dependence for calculating the time interval of gas accumulation in the annulus, during which the dynamic level decreases to the pump intake, is obtained. This value can be used to estimate the frequency of gas withdrawal from the annulus using compressors. It has been found that the rate of increase in annular gas pressure in time increases non-linearly with a rise in the gas-oil ratio and a decrease in water cut, and also linearly increases with a rise in liquid flow rate. Influence of the operating (gas-oil ratio) and technological (value of the gas pressure maintained in the annulus) factors on the flow rate of the suspended reciprocating compressor driven by the beam engine, designed for forced withdrawal and redirection of the annular gas into the flow line of the well is analyzed.
-
Date submitted2020-06-02
-
Date accepted2020-12-15
-
Date published2020-12-29
Method for calculating dynamic loads and energy consumption of a sucker rod installation with an automatic balancing system
The efficiency of sucker rod pump installations, which have become widespread in mechanized lift practice, is largely determined by the balance of the drive. During the operation of sucker rod installations, the balance of loads acting on the rod string and the drive can change significantly due to changes in the dynamic fluid level, which leads to a decrease in balance and an increase in loads on the pumping equipment units. The increase and decrease in the dynamic level in accordance with the pumping and accumulation cycle occurs in wells operating in the periodic pumping mode. It is shown that during the operation of equipment in a periodic mode, fluctuations in the dynamic level and, accordingly, in the loads acting on the nodes occur. This leads to the need for dynamic adjustment of the balancing weights to ensure the balance of the pumping unit. A system for automatic balancing of the rod drive has been developed, including a balancing counterweight, an electric motor that moves the load along the balance beam, a propeller and a computing unit. To study the effectiveness of the proposed device, a complex mathematical model of the joint operation of the reservoir - well - sucker rod pump - rod string – pumping unit has been developed. It is shown that due to the dynamic adjustment of the balance counterweight position, the automatic balancing system makes it possible to significantly reduce the amplitude value of the torque on the crank shaft (in comparison with the traditional rod installation) and provide a more uniform load of the electric motor. Equalization of torque and motor load reduces the power consumption of the unit.
-
Date submitted2017-11-23
-
Date accepted2018-01-19
-
Date published2018-04-24
Theoretical aspects of the technical level estimation of electrical engineering complexes
- Authors:
- S. V. Kolesnichenko
- O. V. Afanaseva
The results of the analysis of methods allowing to evaluate the technical level of the electro technical complex (ETC) are presented and an original technique based on the application of the integral indicator is presented. The characteristic of each stage of the technique is given. The proposed scientific and methodological apparatus for assessing the technical level of the ETС is illustrated by the examples of the executive elements of the ETC comparison (internal combustion engines) using an integral quality index that links both the main characteristics of the samples and the means spent for achieving them. The proposed approach for assessing the technical level and quality of the ETC on the basis of an integral indicator should be carried out already at early stages of the life cycle when solving the following problems: the rationale for the economic feasibility of developing new or improving the quality of the produced ETCs; choice of the best option for the developed ETC; justification of requirements for the ETC; decision-making on the establishment and removal of ETC from production; substantiation of the rules of operation of the ETC in various conditions.
-
Date submitted2015-08-09
-
Date accepted2015-10-05
-
Date published2016-04-22
Inorganic and organic vitreous foam materials and prospect of environmental cleaning from oil and oil products pollutions
- Authors:
- V. E. Kogan
The analysis of own experimental materials which are part of the new scientific direction – complex research of physical and chemical regularities of novel inorganic and organic vitreous sorbents and investigation of the oil and oil products absorption processes by that sorbents developed on department of the General and Physical Chemistry of National Mineral Resources University (Mining University) under the leadership of the author of this paper is provided. In particular, specifics of kinetic curves of oil absorption for sorbents with a vitreous surface are experimentally established and theoretically proved by the conducted researches.
-
Date submitted2015-08-02
-
Date accepted2015-10-04
-
Date published2016-04-22
Development of innovative technologies of dedusting in mining and advance coal mine faces
- Authors:
- G. I. Korshunov
- S. B. Romanchenko
The article describes the results of the implementation of investment projects in the field of complex dedusting implemented in major coal producing companies in Russia. Experimental study of the processes reduce the levels of dust in the workplace in the application of modern systems of irrigation and aspiration systems. The factors that determine the mass and composition of particulate airborne dust at various ways of dust suppression. The results of the analysis of the laser dispersed composition of particles removed from the air of the working area
-
Date submitted2014-09-10
-
Date accepted2014-11-23
-
Date published2015-06-26
Navigation and time support management systems by highly dynamic moving objects
- Authors:
- D. A. Pervukhin
- S. V. Kolesnichenko
Researched topical issues of improving the accuracy of the application of highdynamic aircraft used for the purpose of mineral exploration, environmental monitoring, security, environmental and fire safety, as well as the decisions of other special tasks. The possible variants of construction of control systems of dynamic objects on the basis of integration of traditional inertial navigation systems and user equipment of a network of satellite navigation systems. Justified some schematics, technical and constructive solutions for development of advanced navigation equip-ment of the aircraft.
-
Date submitted2009-08-23
-
Date accepted2009-10-17
-
Date published2010-02-01
Mathematical description of microwave contact level controller for liquid agent
- Authors:
- N. V. Teterin
- O. M. Bolshunova
It is shown the problem of measurement of level in oil tanks. Considered the use of a method of the sway electromagnetic radiation for the control of level of section of environments in tanks, made its mathematical description, resulted the estimation of results of practical application.
-
Date submitted2008-11-01
-
Date accepted2009-01-22
-
Date published2009-12-11
Rate setting of electrical equipment reserve stocks on the enterprises of the gas main transport
- Authors:
- L. V. Vazhenina
Minimization of economic losses from downtime of equipment and, first of all, off-schedule (breakdowns, accidents) is an actual problem whose solution can be achieved by the development and creation of a reserve stocks (irreducible level) materials and spare parts of electrical equipment. As a result of the study and comparative analysis of different methods for determining the amount of the reserve stocks has been concluded that these approaches are not fully reflect the real needs of the enterprise. In this regard, has developed an optimal method for determining the amount of irreducible level of reserve stocks of electrical equipment, taking into account the rational order of delivery of equipment, spare parts.
-
Date submitted1954-08-16
-
Date accepted1954-10-26
-
Date published1956-01-17
Электроуровнемер для замера динамического уровня воды в скважинах
- Authors:
- Unknown
Электроуровнемер предназначен для замера динамического уровня воды в скважинах при откачках (рис. 1). Предельная глубина, измеряемая прибором, 100 м, точность измерения + 0,05%. Принцип действия прибора основан на замыкании электрической цепи между опускаемым в скважину наконечником и водой, определяемом по отклонению стрелки гальванометра (рис. 2). Глубина, на которой происходит замыкание цепи, определяется длиной изолированного провода, опущенного в скважину (см. статью). В заключение отметим, что описанный выше электроуровнемер дает вполне достаточную для практики точность измерения как статического, так и динамического уровней воды в скважинах при одиночных и кустовых откачках.
-
Date submitted1954-08-26
-
Date accepted1954-10-08
-
Date published1956-01-17
Оголовки для центральной и наблюдательной скважин, облегчающие наблюдение за динамическими уровнями
Центральная скважина. При организации опытных откачек, эрлифтом динамические уровни воды в центральной скважине обычно остаются вне наблюдений, так как водоподъемная труба заполняется эмульсией, маскирующей положение динамического уровня. Для наблюдений за динамическими уровнями проходят специальную наблюдательную скважину малого диаметра (пьезометр) в непосредственной близости от центральной скважины, и называют ее затрубной наблюдательной скважиной. При глубоком залегании динамического уровня в водоносном горизонте проходка и крепление затрубной скважины становятся затруднительными. Очень удобно такую скважину заменить пьезометрической трубкой, опущенной в центральную скважину рядом с воздушной трубой. Если нижний обрез пьезометрической трубки погрузить на 5—10 м ниже смесителя, то вода в ней полностью освобождается от воздействия подаваемого в центральную скважину воздуха и устанавливается на уровне, соответствующем динамическому уровню в центральной скважине и водоносном горизонте. Остается только периодически замерять положение этого уровня уровнемером. Удобен уровнемер Б. П. Остроумова.