-
Date submitted2023-08-14
-
Date accepted2023-12-27
-
Date published2024-12-25
Modelling of compositional gradient for reservoir fluid in a gas condensate deposit with account for scattered liquid hydrocarbons
In oil and gas reservoirs with significant hydrocarbon columns the dependency of the initial hydrocarbon composition on depth – the compositional gradient – is an important factor in assessing the initial amounts of components in place, the position of the gas-oil contact, and variations of fluid properties throughout the reservoir volume. Known models of the compositional gradient are based on thermodynamic relations assuming a quasi-equilibrium state of a multi-component hydrodynamically connected hydrocarbon system in the gravity field, taking into account the influence of the natural geothermal gradient. The corresponding algorithms allow for calculation of changes in pressure and hydrocarbon fluid composition with depth, including determination of the gas-oil contact (GOC) position. Above and below the GOC, the fluid state is considered single-phase. Many oil-gas-condensate reservoirs typically have a small initial fraction of the liquid hydrocarbon phase (LHC) – scattered oil – within the gas-saturated part of the reservoir. To account for this phenomenon, a special modification of the thermodynamic model has been proposed, and an algorithm for calculating the compositional gradient in a gas condensate reservoir with the presence of LHC has been implemented. Simulation cases modelling the characteristic compositions and conditions of three real oil-gas-condensate fields are considered. The results of the calculations using the proposed algorithm show peculiarities of variations of the LHC content and its impact on the distribution of gas condensate mixture composition with depth. The presence of LHC leads to an increase in the level and possible change in the type of the fluid contact. The character of the LHC fraction dependency on depth can be different and is governed by the dissolution of light components in the saturated liquid phase. The composition of the LHC in the gas condensate part of the reservoir changes with depth differently than in the oil zone, where the liquid phase is undersaturated with light hydrocarbons. The results of the study are significant for assessing initial amounts of hydrocarbon components and potential efficiency of their recovery in gas condensate and oil-gas-condensate reservoirs with large hydrocarbon columns.
-
Date submitted2021-09-17
-
Date accepted2022-04-07
-
Date published2022-12-29
Technique for calculating technological parameters of non-Newtonian liquids injection into oil well during workover
Technique for automated calculation of technological parameters for non-Newtonian liquids injection into a well during workover is presented. At the first stage the algorithm processes initial flow or viscosity curve in order to determine rheological parameters and coefficients included in equations of rheological models of non-Newtonian fluids. At the second stage, based on data from the previous stage, the program calculates well design and pump operation modes, permissible values of liquid flow rate and viscosity, to prevent possible hydraulic fracturing. Based on the results of calculations and dependencies, a decision is made on the necessity of changing the technological parameters of non-Newtonian liquid injection and/or its composition (components content, chemical base) in order to prevent the violation of the technological operation, such as unintentional formation of fractures due to hydraulic fracturing. Fracturing can lead to catastrophic absorptions and, consequently, to increased consumption of technological liquids pumped into the well during workover. Furthermore, there is an increased risk of uncontrolled gas breakthrough through highly conductive channels.
-
Date submitted2020-07-29
-
Date accepted2021-03-30
-
Date published2021-06-24
Model of baddeleyite recovery from dump products of an apatite-baddeleyite processing plant using a CVD6 concentrator
The paper is devoted to developing a model of baddeleyite recovery from dump products of an apatite-baddeleyite processing plant using centrifugal concentrators. The relevance of the work arises from the acquisition of new knowledge on the optimization of technological parameters of centrifugal concentrators using Knelson CVD (continuous variable discharge) technology – in particular, setting the frequency of valve opening and the duration of valves remaining open. The purpose of the research was to assess the applicability of CVD technology in the treatment of various dump products of the processing plant and to build a model of dependencies between the concentrate and tailings yields and the adjustable parameters, which will allow to perform preliminary calculations of the efficiency of implementing this technology at processing plants. The research objects are middling and main separation tailings of the coarse-grained stream and combined product of main and recleaner separation tailings of the fine-grained stream. The study uses general methods of mathematical statistics: methods of regression analysis, aimed at building statistically significant models, describing dependence of a particular variable on a set of regressors; group method of data handling, the main idea of which is to build a set of models of a given class and choose the optimal one among them. Authors proposed an algorithm for processing experiment results based on classical regression analysis and formulated an original criterion for model selection. Models of dependencies between the concentrate and tailings yields and the adjustable parameters were built, which allowed to establish a relationship between the concentrate yield and the valve opening time, as well as a relationship between the tailings yield and the G-force of the installation.
-
Date submitted2020-05-25
-
Date accepted2020-06-11
-
Date published2020-12-29
Technological aspects of cased wells construction with cyclical-flow transportation of rock
- Authors:
- Andrei S. Kondratenko
A high-performance technology for constructing cased wells is proposed. Essence of the technology is the advance insertion of the casing pipe into the sedimentary rock mass and the cyclical-flow transportation of the soil rock portions using the compressed air pressure supplied to the open bottomhole end of the pipe through a separate line. Results of mathematical modeling for the process of impact insertion of a hollow pipe into a soil mass in horizontal and vertical settings are considered. Modeling of the technology is implemented by the finite element method in the ANSYS Mechanical software. Parameters of the pipe insertion in the sedimentary rock mass are determined - value of the cleaning step and the impact energy required to insert the pipe at a given depth. Calculations were performed for pipes with a diameter from 325 to 730 mm. Insertion coefficient is introduced, which characterizes the resistance of rocks to destruction during the dynamic penetration of the casing pipe in one impact blow of the pneumatic hammer. An overview of the prospects for the application of the proposed technology in geological exploration, when conducting horizontal wells of a small cross-section using a trenchless method of construction and borehole methods of mining, is presented. A variant of using the technology for determining the strength properties of rocks is proposed. Some features of the technology application at industrial facilities of the construction and mining industry are considered: for trenchless laying of underground utilities and for installing starting conductors when constructing degassing wells from the surface in coal deposits. Results of a technical and economic assessment of the proposed technology efficiency when installing starting conductors in sedimentary rocks at mining allotments of coal mines are presented.
-
Date submitted2019-03-31
-
Date accepted2019-08-25
-
Date published2020-02-25
Cascade frequency converters control features
The structures of systems with high-voltage cascade frequency converters containing multi-winding transformers and low-voltage low-power converters connected in series at each output phase of the load are considered. Low-voltage blocks contain three-phase diode or active rectifiers, DC capacitor filters, single-phase stand-alone voltage inverters and block disconnecting devices in partial modes (in case of failure when part of the blocks are disconnected). The possibilities of operation of cascade converters are determined, equations for correcting tasks to units in partial modes are given, tables of correction of tasks with estimates of achievable load characteristics are proposed. The results of experiments on the model of a powerful installation with a cascade frequency converter are presented, confirming the possibility of ensuring the symmetry of the load currents when disconnecting part of the blocks and the asymmetry of the circuit.
-
Date submitted2015-08-18
-
Date accepted2015-10-06
-
Date published2016-04-22
Energy- efficient control of asynchronous motor drive with current refinement of the loss minimum on the basis of fuzzy logic
- Authors:
- O. B. Shonin
- V. S. Pronko
Currently, asynchronous electric drive on the basis of semiconductor frequency converters is widespread because of the relative simplicity and reliability of the design, the use of digital control systems, providing the accuracy and flexibility of process control, which allows for a significant increase in product quality, reduction in energy consumption and improvement of the enterprise profitability. In spite of these advantages, the problem of ensuring high energy efficiency of the drive in wide range of its operational modes is still not solved in full scale. The paper is devoted to the reduction of losses in the asynchronous drive on the basis of en-ergy-saving control algorithms that aim to ensure the desired mode of the driven mechanism while minimizing losses in copper and steel of the motor. On the basis of the motor model, taking into account magnetic losses, dependences of losses in the copper and steel, as well as the total loss from the absolute slip have been derived for different operating points of the drive. The optimal values of the absolute slip for different speeds of the rotor have been obtained for use in the con-trollers ensuring operation of the drive at maximum efficiency, highest power factor and minimum of the stator current. For minimizing the losses in the drive when changing the motor parameters it has been offered the combined method based on the method of loss model and iterative method of searching the minimum of power consumption. The effectiveness of the proposed control system using fuzzy logic is confirmed by comparing the graphs of losses and efficiency, obtained at using a traditional control law and the optimal control law.
-
Date submitted2014-12-27
-
Date accepted2015-03-01
-
Date published2015-12-25
Minimization of energy losse when starting a variable frequency drive through application of a genetic algorithm of optimization
- Authors:
- O. B. Shonin
- V. S. Pronko
In the face of energy lack and rising energy prices one of the priorities of current researches is to improve energy efficiency of electric drives, which are widely used in modern industrial plants. Existing methods of minimizing losses are mainly designed for stationary regimes. At the same time, the development of algorithms for reducing losses in transient and in particular starting conditions is given little attention. Due to the high complexity of the description of the multivari-ate dynamic processes determining the optimal control laws is advantageously to be carried out us-ing stochastic optimization methods. The work seeks to substantiate the optimal starting character-istics of an asynchronous drive based on a genetic algorithm. A feature of the proposed method of optimization is the use of multiple simulation experiments to find start-up characteristics which provide a minimum energy loss. Automation of the search is performed using the developed pro-gram, which includes a module of a genetic algorithm and a module for interfacing with the elec-tric model in the MATLAB/Simulink environment. The program allows choosing the parameters of the genetic algorithm along with controlling the process of optimization. Application of the proposed method allowed obtaining the optimal starting characteristics «voltage – frequency» in a tabular form with consequent linear approximation of the data. Increase in efficiency due to the proposed start up law has been confirmed by comparing the simulation re-sults under conditions of using a traditional linear characteristic and derived optimal law. The es-timation of losses reduction has been carried out at the drive load of different kind in a wide range of its variation.
-
Date submitted2013-07-18
-
Date accepted2013-09-02
-
Date published2014-03-17
Rock mechanics problems decision algorithm for bottom layers of potash salt deposits
Decision algorithm for rock mechanics problems for bottom layers of potash deposits is suggested. Flow chart for the algorithm and it’s parts is shown. The algorithm represents the method to choose excavation technology for multi-layer potash deposits.
-
Date submitted2009-10-09
-
Date accepted2009-12-12
-
Date published2010-09-22
Stress condition of prefabricated tunnel linning with initial release
- Authors:
- E. A. Karasev
3d finite element model of soil and prefabricated tunnel lining interaction with appropriate boundary condition is given in this article. Stresses distribution on inner and outer part of the tunnel lining is analyzed. Relationship between stress state at top and sides of the tunnel lining and deformation module magnitude is shown.
-
Date submitted2008-10-20
-
Date accepted2008-12-22
-
Date published2009-12-11
Analytical continuation of geophysical fields by continued fractions method
- Authors:
- K. M. Ermokhin
The most close to reality geophysical field description is the approximation of the fraction-rational type. In this case the presence of poles in the lower half space corresponds adequately to the denominator zeros. This article contains the theory and algorithm of realization of this conception. The proposed method is called – Continued Fraction Continuation Method.