Submit an Article
Become a reviewer
E. A. Kremcheev
E. A. Kremcheev
Postgraduate student
G.V. Plekhanov Saint Petersburg State Mining Institute
Postgraduate student
G.V. Plekhanov Saint Petersburg State Mining Institute

Articles

Geoecology and occupational health and safety
  • Date submitted
    2018-08-25
  • Date accepted
    2018-10-26
  • Date published
    2019-02-25

METROLOGICAL SUPPORT OF MONITORING SYSTEMS BASED ON UNMANNED AERIAL VEHICLES

Article preview

The article discusses the fields and methods of application of unmanned aerial vehicles (UAV). Current legislation in Russia and in the world, significantly limit the use of UAV in monitoring. For the first time, we present a solution to the problem of a monitoring measurement system included in the state register of measuring instruments using the example of the basic UAV model. We conducted an analysis of promising approaches to the creation of UAV metrological and methodological support, as well as ways to adapt their target load to meet the challenges of operational monitoring of air pollution.

How to cite: Kremcheev E.A., Danilov A.S., Smirnov Y.D. METROLOGICAL SUPPORT OF MONITORING SYSTEMS BASED ON UNMANNED AERIAL VEHICLES // Journal of Mining Institute. 2019. Vol. 235. p. 96. DOI: 10.31897/PMI.2019.1.96
Mining
  • Date submitted
    2017-12-28
  • Date accepted
    2018-03-03
  • Date published
    2018-06-25

Special features of a structure of technical operations for peat excavation with stage dewatering

Article preview

A method of development of a technology of peat extraction for intensifying of dewatering which involves drying of peat raw materials in thick layers with a layer-by-layer harvesting into large-sized roll with further delivery to the field storage unit of the enlarged sizes is presented in the paper. Throughout the year storage raw materials may be transported to the customer or to the shopfloor for further processing. Considering dimension and mass characteristics, a crumbed peat of various moisture capacity is a major type of products to be of high demand. On the basis of the results of scientific studies regarding gravity dewatering of peat and its drying in field environment, the ways of intensifying of field dewatering of peat for extraction at shallow-peat lands and fine-limit fields are proposed. The presented results of the experimental performance of a technology of peat drying in thick layers with a layer-by-layer harvesting indicate an increase of seasonal harvesting and a decrease of the influence of unfavorable meteorological factors on the stability of the extraction process. Performed investigations allowed to develop a structure of technical operations for peat excavation with the stage dewatering in spreading and intermediate storage units providing rational state of the extraction process regarding a complex of technical factors. A suggested scheme of a process area for a primary and secondary period of deposit exploitation by a technology of peat excavation is considered.

How to cite: Kremcheev E.A. Special features of a structure of technical operations for peat excavation with stage dewatering // Journal of Mining Institute. 2018. Vol. 231. p. 225. DOI: 10.25515/PMI.2018.3.225
Manufacturing machinery and equipment
  • Date submitted
    2013-09-01
  • Date accepted
    2013-11-10
  • Date published
    2014-03-01

Model of moisture movement in field dressing of peat in the large spreading

Article preview

The possibility of using the model equilibrium disturbed peat system to assess the effectiveness of gravitational drainage of the peat material hill without evaporation from the surface, depending on the height of the critical thickness, flow rate and the amount of moisture in the layer after deposition.

How to cite: Kremcheev E.A., Nagornov D.O. Model of moisture movement in field dressing of peat in the large spreading // Journal of Mining Institute. 2014. Vol. 209. p. 59.
Geology and metallogeny
  • Date submitted
    2012-07-29
  • Date accepted
    2012-09-07
  • Date published
    2013-01-01

Peat resources of the North-West federal district of the Russia and prospect of their development

Article preview

This paper provides an overview of the current analysis of peat resources distribution of Northwest Federal district. The analysis of peat industry is resulted. The power effective technology of career extraction of peat raw materials and manufacture of agglomerated peat fuel for needs of the distributed power is  offered.

How to cite: Mikhailov A.V., Ivanov S.L., Bolshunov A.V., Kremcheev E.A. Peat resources of the North-West federal district of the Russia and prospect of their development // Journal of Mining Institute. 2013. Vol. 200. p. 226.
Mining electromechanics and mining equipment
  • Date submitted
    2011-08-05
  • Date accepted
    2011-10-26
  • Date published
    2012-02-01

Mechanisation of extraction of peat from undrained deposit

Article preview

In comparison with traditional methods of extraction using the offered equipment and developed technological schemes for industrial production of a peat will allows to avoid actions on drainage of developed fields; to reduce expenses for preparation and operation of a peat deposit; to prolong a season of mining activities, and in some cases to provide an opportunity of all-the-year-round operation of a deposit.

How to cite: Mikhailov A.V., Kremcheev E.A., Nagornov D.O. Mechanisation of extraction of peat from undrained deposit // Journal of Mining Institute. 2012. Vol. 196. p. 256.
Mining electromechanics and mining equipment
  • Date submitted
    2011-07-28
  • Date accepted
    2011-09-25
  • Date published
    2012-01-01

Design features of replacement work equipment of peat excavation laoding machine

Article preview

The article deals with design features a removable desktop equipment peat excavation, loading machine. The analysis of the structures of the working equipment of peat excavation, loading machines. Suggest ways to improve the design of the working equipment of peat excavation, loading machines.

How to cite: Nagornov D.O., Kremcheev E.A. Design features of replacement work equipment of peat excavation laoding machine // Journal of Mining Institute. 2012. Vol. 195. p. 272.
Technological machinery and equipment of mining and oil & gas industries
  • Date submitted
    2007-11-13
  • Date accepted
    2008-01-18
  • Date published
    2008-05-01

Calculation of loads on walls of cylindro-conical hoppers.

Article preview

For calculations of designs accumulating, running (dampering) bunkers design procedures of the elementary forms the vertical cylinder or even slot-hole capacity with vertical parallel walls are used and processes of movement of a material are not considered in any way at release. The method of calculation for the combined form of the bunker in view of physicomechanical properties of a material of loading and walls of the bunker (a corner of a natural slope, bulk weight, factors of friction between particles of a material and particles about walls of the bunker is offered at rest and movement of a material) on the basis of use of model of the discrete environment in the form of regular stacking spheres.

How to cite: Batalov A.P., Kremcheev E.A. Calculation of loads on walls of cylindro-conical hoppers. // Journal of Mining Institute. 2008. Vol. 178. p. 31-34.
Technological machinery and equipment of mining and oil & gas industries
  • Date submitted
    2007-11-18
  • Date accepted
    2008-01-05
  • Date published
    2008-05-01

Estimation of lubricating ability of oils of transmissions of mining machines

Article preview

Lubricating value shows loading capacity of transmission oil. Poor lubricating value of friction couples which are used at borderline lubrication ordinary have wear-out areas and these friction couples also fiercely attacked by corrosion. That’s why a decision of choosing oil type have to be substantiated. In this article rapid method of lubricating capacity tests is offered.

How to cite: Poddubnaya A.A., Fokin A.S., Ivanov S.L., Kremcheev E.A., Potapenko V.S. Estimation of lubricating ability of oils of transmissions of mining machines // Journal of Mining Institute. 2008. Vol. 178. p. 86-90.
Diagnostics and control of technical systems and their elements. New technologie
  • Date submitted
    2007-11-24
  • Date accepted
    2008-01-13
  • Date published
    2008-05-01

The area of existence of involute gear mesh with a given overlap coefficient

Article preview

It is shown, that application of the combined displacement while designing toothed gearings considerably allows to expand area of existence of gearing with a non-standard radial backlash. Influence of parameters of the tool on area of existence of gearing is submitted, the technology of realization of tangential displacement by generation of gears is described.

How to cite: Fokin A.S., Poddubnaya A.A., Ivanov S.L., Kremcheev E.A. The area of existence of involute gear mesh with a given overlap coefficient // Journal of Mining Institute. 2008. Vol. 178. p. 191-194.
Mining engineering technologies. Diagnostics and control of technical systems and their elements. New technologies
  • Date submitted
    2003-07-03
  • Date accepted
    2003-08-06
  • Date published
    2004-02-01

Energy service life of the plain bearing

Article preview

Design schemes of pneumatic, hydraulic and drilling machines with combined drive, used in mines and mines, mainly have mechanical drives of drilling rod rotation. This refers to machines of domestic and foreign production. A considerable part of failures of drilling equipment occurs exactly due to the fault of rotary units. One of the weak points of the design is often the transmission output shaft support unit made on the basis of plain bearing. The energy and life of such a sliding bearing is limited by the limit value of wear, leading to the occurrence of unacceptable misalignment of the gear wheels’ axes. The expression for determining the energy resource of the plain bearing from the condition of permissible volume wear of the liner material is proposed.

How to cite: Kremcheev E.A., Ivanov S.L. Energy service life of the plain bearing // Journal of Mining Institute. 2004. Vol. 157. p. 178-180.
Mining engineering technologies. Diagnostics and control of technical systems and their elements. New technologies
  • Date submitted
    2003-07-15
  • Date accepted
    2003-08-22
  • Date published
    2004-02-01

On the construction of a monitoring system for the operation of self-propelled equipment in underground mines

Article preview

The possibility of monitoring of underground self-propelled equipment is shown. The use of on-board measuring instruments in combination with software systems for planning, accounting of work, organization of maintenance and repair, as well as a systematized approach to accounting for the influence of operating conditions on the efficiency of the underground self-propelled machine operation has been suggested.

How to cite: Kuleshov A.A., Grigorev E.A., Kremcheev E.A., Linnik V.B. On the construction of a monitoring system for the operation of self-propelled equipment in underground mines // Journal of Mining Institute. 2004. Vol. 157. p. 186-189.
Mining electromechanics
  • Date submitted
    2002-06-14
  • Date accepted
    2002-07-03
  • Date published
    2003-01-01

Estimation of energy flow losses in the gearing

Article preview

Rotary-impact drill heads with a mechanical rotator transmission are widespread in mines and mines. A typical representative of this class of machines are BGA type units. The revealed data about breakdowns of BHA drill head show that actual lifetime of transmission elements is 60-100 hours, while the regulated lifetime is 360-1440 hours. To estimate the service life of parts and to find the weakest elements of the transmission, the energy method was chosen. When using this approach, it was necessary to consider the influence of inaccuracies in the location of transmission components on their service life. The positioning inaccuracies cause a shift in the meshing of the ring gear, and the load distribution along the width has a variable character, which leads to the reduction of the transmission life due to the occurrence of stresses in some parts of the ring gear, which exceed the allowable stresses. Thus, there was a need to take into account the non-uniformity of energy resource consumption depending on the actual contact width, nature and size of the external load. In order to solve this problem, a laboratory bench for testing the gears was created at the department. Experimental studies carried out on the stand showed that when the contact width changes by more than three times, the losses in the meshing differ little. Obviously, there is a change in the energy balance. The energy flow losses absorbed by the part and going directly to the destruction of the crystal lattice of the material increase, which leads to a more intensive expenditure of the energy resource of the gearing.

How to cite: Kremcheev E.A. Estimation of energy flow losses in the gearing // Journal of Mining Institute. 2003. Vol. № 1 155. p. 149-152.