-
Date submitted2023-07-04
-
Date accepted2024-05-02
-
Date published2025-02-25
Study of the pore structure in granite and gabbrodolerite crushed stone grains of various sizes
- Authors:
- Elena E. Kameneva
- Viktoriya S. Nikiforova
The results of a study on the pore structure of crushed stone grains of various sizes, obtained through staged disintegration of gabbrodolerite and microcline granite – rocks differing in texture, structure, and mineral composition – are presented. Research conducted using X-ray computed microtomography revealed that disintegration leads to changes in the pore structure of the rocks. The increase in overall porosity and pore concentration in the crushed stone grains is associated with the formation of newly developed pores of various sizes and sphericity. A clear relationship between the porosity of the crushed stone grains and their size is absent, which is due to the textural and structural characteristics as well as the mineral composition of the original rocks. The scale factor is evident only in the case of gabbrodolerite, which is characterized by a fine-grained structure, massive texture, and stable mineral composition. Fine gabbrodolerite grains exhibit lower pore concentration compared to larger grains, which aligns with the statistical theory of rock strength, according to which the probability of defects (pores and microcracks) decreases as the sample size diminishes – the smaller the grain size, the higher its strength. In contrast, for porphyritic granites with an uneven grain size, the trend is reversed – smaller grains are more porous. A study of the porosity of individual rock-forming minerals in granite showed that pores are unevenly distributed in the granite crushed stone grains. The highest concentration of pores is typical for microcline. The presence of brittle and porous microcline inclusions in the granite crushed stone grains leads to the formation of new pores and microcracks, whose number increases with the repeated application of load during staged disintegration.
-
Date submitted2024-05-28
-
Date accepted2024-11-07
-
Date published2024-12-25
Methods of intensification of pipeline transportation of hydraulic mixtures when backfilling mined-out spaces
The paper presents an analysis of the advantages and limitations of additional measures to intensify the transportation of the backfill hydraulic mixture flow. The results of the analysis of the conditions for using pumping equipment to move flows with different rheological properties are shown. Generalizations of the methods for influencing the internal resistance of backfill hydraulic mixtures by means of mechanical activation, as well as increasing fluidity due to the use of chemical additives are given. The article presents the results of studies confirming the feasibility of using pipes with polymer lining, which has proven its efficiency in pumping flows of hydraulic mixtures with different filler concentrations. An analytical model of hydraulic mixture movement in the pipeline of the stowage complex has been developed. The trends in pressure change required to ensure the movement of hydraulic mixture in pipelines of different diameters are exponential, provided that the flow properties are constant. The effect of particle size on the motion mode of the formed heterogeneous flow, as well as on the distribution of flow density over the cross-section, characterizing the stratification and change in the rheological properties of the backfill hydraulic mixture, is assessed. An analytical model of centralized migration of the dispersed phase of the hydraulic mixture flow is formulated, describing the effect of turbulent mixing of the flow on the behavior of solid particles. An assessment of the secondary dispersion of the solid fraction of the hydraulic mixture, which causes a change in the consistency of the flow, was performed. The studies of the influence of the coefficient of consistency of the flow revealed that overgrinding of the fractions of the filler of the hydraulic mixture contributes to an increase in the required pressure in the pipeline system.
-
Date submitted2024-04-16
-
Date accepted2024-09-24
-
Date published2024-11-12
Deep-buried Lower Paleozoic oil and gas systems in eastern Siberian Platform: geological and geophysical characteristics, estimation of hydrocarbon resources
The study of deep-buried oil and gas systems is a promising trend in the preparation of hydrocarbon resources. The study of the factors determining oil and gas potential is extremely important. The Lena-Vilyui sedimentary basin in the eastern Siberian Platform has a potential for the discovery of large oil and gas fields in deep-buried Cambrian deposits. The use of original methodological approaches to the analysis of black shale and overlying deposits, generalization of the results of lithological, biostratigraphic and geochemical studies of Cambrian deposits in territories adjoining the study area, modern interpretation of geophysical data showed that siliceous, carbonate, mixed rocks (kerogen-mixtite) of the Kuonamka complex and clastic clinoform-built Mayan deposits are most interesting in terms of oil and gas potential. Oil and gas producing rocks of the Lower and Middle Cambrian Kuonamka complex subsided to the depths of 14 km. The interpretation of modern seismic surveying data confirms the hypothesis of a limited occurrence of the Upper Devonian Vilyui rift system. Based on generalization of geological, geophysical and geochemical archival and new materials on the Lower Paleozoic deposits of the eastern Siberian Platform, a probabilistic estimation of geological hydrocarbon resources of the Cambrian and younger Paleozoic complexes in the Lena-Vilyui sedimentary basin was performed. Based on basin modelling results it was concluded that the resources were mainly represented by gas. It is presumed that oil resources can be discovered in traps of the barrier reef system as well as on the Anabar and Aldan slopes of the Vilyui Hemisyneclise. With a confidence probability of 0.9, it can be stated that total initial resources of oil and gas (within the boundaries of the Vilyui Hemisyneclise) exceed 5 billion t of conventional hydrocarbons. The recommended extremely cautious estimate of resources of the pre-Permian complexes is 2.2 billion t of conventional hydrocarbons. In the study area, it is necessary to implement a program of deep and super-deep parametric drilling without which it is impossible to determine the oil and gas potential of the Lower Paleozoic.
-
Date submitted2022-04-18
-
Date accepted2022-06-15
-
Date published2022-07-26
Results and prospects of geological mapping of the Arctic shelf of Russia
- Authors:
- Evgeny A. Gusev
The results of compiling the sets of the State Geological Map at a scale of 1:1,000,000 for the Arctic continental shelf of Russia are analyzed. Results are summed up, and the main problems of geological mapping are outlined. The results of geological and geophysical studies of the Arctic Ocean are of great importance for deciphering the geological evolution. The Arctic shelf is the widest shelf in the world, while the spreading ocean basin is one of the narrowest and is characterized by anomalous structural features. The main problems of geological mapping include identification the sedimentary cover/folded basement boundary, interpretation the geodynamic evolution of the shelf and adjacent ocean, determining the rates of sedimentation and stratigraphic subdivision of the sedimentary cover due to a small number of key boreholes. It is promising to further study problem areas with unclear features of geological structure as well as small-scale mapping in areas of industrial development on the Arctic continental shelf.
-
Date submitted2019-12-25
-
Date accepted2020-06-30
-
Date published2020-10-08
Accounting of geomechanical layer properties in multi-layer oil field development
Amid the ever-increasing urgency to develop oil fields with complex mining and geological conditions and low-efficiency reservoirs, in the process of structurally complex reservoir exploitation a number of problems arise, which are associated with the impact of layer fractures on filtration processes, significant heterogeneity of the structure, variability of stress-strain states of the rock mass, etc. Hence an important task in production engineering of such fields is a comprehensive accounting of their complex geology. In order to solve such problems, the authors suggest a methodological approach, which provides for a more reliable forecast of changes in reservoir pressure when constructing a geological and hydrodynamic model of a multi-layer field. Another relevant issue in the forecasting of performance parameters is accounting of rock compressibility and its impact on absolute permeability, which is the main factor defining the law of fluid filtration in the productive layer. The paper contains analysis of complex geology of a multi-layer formation at the Alpha field, results of compression test for 178 standard core samples, obtained dependencies between compressibility factor and porosity of each layer. By means of multiple regression, dependencies between permeability and a range of parameters (porosity, density, calcite and dolomite content, compressibility) were obtained, which allowed to take into account the impact of secondary processes on the formation of absolute permeability. At the final stage, efficiency of the proposed methodological approach for construction of a geological and hydrodynamic model of an oil field was assessed. An enhancement in the quality of well-by-well adaptation of main performance parameters, as well as an improvement in predictive ability of the adjusted model, was identified.
-
Date submitted2018-06-28
-
Date accepted2018-09-15
-
Date published2018-12-21
Causes of fluid entry absence when developing wells of small deposits (on the example of Khadum-Batalpashinsky horizon)
- Authors:
- R. A. Gasumov
A promising direction for the development of the oil and gas industry is the drilling of small hydrocarbon fields, which constitute two thirds of Russia's total hydrocarbon reserves. When choosing an effective method of development and assessing the potential of small fields in Eastern Ciscaucasia, which are characterized by complex mining and geological conditions with abnormally high reservoir pressures and temperatures, it is necessary to determine the optimal amount of oil production taking into account the flow of edge water under elastic water drive. The article discusses the reasons for the lack of inflows of reservoir fluids in wells during their development, which are due to complex unconventional fractured clay reservoirs in the lower Maykop deposit and the presence of loose rocks in the section of the reservoir. The results of studies of the influence of technological and geological factors on the poroperm properties of the Khadum-Batalpashinsky reservoir are described, zones of rock softening are revealed, the intervals with bottom water and their influence on the well development process are specified. It has been established that the state of the hydrodynamic system of the field depends on the introduction of the bottom and edge waters of the sedimentation basin of the East Stavropol Depression. Oil deposits in the Khadum and Batalpashinskaya suites initially work in an elastic and then in an elastic-water drive mode. The main reasons for the lack of inflows of formation fluids into wells are the low reservoir properties of clay fractured reservoir rocks; clogging of the fracture capacity of reservoir rocks at the drilling in as a result of penetration of drilling mud and its filtrate deep into the reservoir; inflow of formation water from an overlying aquifer with abnormally high formation pressure; the closure of cracks in the clay reservoir due to a sharp decrease in pressure caused by the lowering of the slotted filter into the well; secondary dissection of productive layers by perforation during repression on the formation in a liquid medium with the presence of a solid phase and high density.
-
Date submitted2017-10-25
-
Date accepted2018-01-17
-
Date published2018-04-24
Innovative technology of large-size products manufacture
- Authors:
- S. N. Sanin
- N. A. Pelipenko
Advantages and prospects for the use of mobile robotic machine-tools in the manufacture of large parts in the mining, cement and nuclear industries are considered, as well as the importance of using welded structures to reduce production costs. Schemes for finishing mechanical machining of welded large-sized parts such as bodies of revolution with the use of mobile robotic machine-tools equipped with a belt-grinding tool, an enlarged description of the technological process for manufacturing a large-sized shell of a welded structure are presented. The conclusion is made that it is necessary to take into consideration the use in the industry of frameless production technology, especially for the machining of large-sized parts, and the use of small mobile robotic machine-tools is a productive approach and has a prospective character. The technological approaches proposed in the article make it possible to remove the restriction on the overall size and mass of the parts being manufactured, which are proposed to be manufactured directly at the site of future operation. The effectiveness of this technology is confirmed both by theoretical research and by practical data of the authors. It was noted that the production by the domestic machine-tool industry of mobile universal and special robotic machine-tools will allow the country's engineering industry to be brought to a new, high-quality world level.
-
Date submitted2017-11-17
-
Date accepted2018-01-05
-
Date published2018-04-24
Estimation of the relation of strength and ultrasound speed in glass-reinforce plastic
- Authors:
- A. I. Potapov
In mining machinery, details and products made of composite materials are widely used, especially from GRP (glass-reinforce plastic). The work evaluates the relationship between the strength and the speed of ultrasound for nondestructive testing of strength in an article made of composite materials such as GDR with the use of a pulsed ultrasonic method. Methods for estimating the connection, the method of mechanical compression tests and mathematical processing and establishing the relationship between the ultrasonic velocity and the strength of GRP are considered. The results of experimental studies on establishing the relationship between the strength of GRP on compression and the speed of longitudinal ultrasonic waves are presented. As a result of statistical processing of the experimental results, equations of the relationship between the compressive strength and the ultrasonic velocity in fiberglass are obtained.
-
Date submitted2016-09-02
-
Date accepted2016-11-08
-
Date published2017-02-22
Mathematical models of gas-dynamic and thermophysical processes in underground coal mining at different stages of mine development
- Authors:
- M. V. Gryazev
- N. M. Kachurin
- S. A. Vorobev
New trends have been traced and the existing ones refined regarding filtration and diffusive motion of gases in coal beds and surrounding rock, spontaneous heating of coal and transport of gas traces by ventilation currents in operating coal mines. Mathematical models of gas-dynamic and thermophysical processes inside underworked territories after mine abandonment have been justified. Mathematical models are given for feasible air feeding of production and development areas, as well as for the development of geotechnical solutions to ensure gas-dynamic safety at every stage of coal mine operation. It is demonstrated that the use of high-performance equipment in the production and development areas requires more precise filtration equations used when assessing coal mine methane hazard. A mathematical model of pressure field of non-associated methane in the edge area of the coal seam has been justified. The model is based on one-dimensional hyperbolic equation and takes into consideration final rate of pressure distribution in the seam. Trends in gas exchange between mined-out spaces of high methane- and CO 2 -concentration mines with the earth surface have been refined in order to ensure environmental safety of underworked territories.
-
Date submitted2014-12-25
-
Date accepted2015-02-01
-
Date published2015-12-25
Deep structure and composition characteristics of the continental earth's crust geostructures on the Russian Federation territory
- Authors:
- A. S. Egorov
Principal features of deep structure and composition of the lithosphere geostructures of the continental part of the Russian Federation territory are characterized within the radial-zonal model of the Earth’s crust. The principal units of the model are megablocks (paleoplites) with ancient layered continental crust and interblock megazones (structures of tension, compression and shear), separating them. The results of the geological-geophysical modeling are presented in the form of layer by layer deep structure schemes – of consolidated basement and of the platform cover and accompanied by a set of the earth's crust sections, carried out along regional profiles, performed with the application of a deep seismic sounding (DSS) method and reflected waves of common depth point (CDP) method.
-
Date submitted2009-10-29
-
Date accepted2009-12-26
-
Date published2010-09-22
Control system of rock pressure at the «Antey» deposit
- Authors:
- B. A. Prosekin
- E. A. Ilin
The paper deals with the geomechanical monitoring system of the Antey deposits of uranium ores. Characteristics of the methods and means for rock pressure control are given.
-
Date submitted2009-09-14
-
Date accepted2009-11-28
-
Date published2010-06-25
Formаtion of a new type individuality under the conditions of generation of integration of interdependent communities
- Authors:
- A. I. Mikheev
This paper deals with the question of model generation of a new type individuality, that contemporary society demands for an advanced, deteriorative-free, balanced and creative development, which renders possible the elaboration of a system of formation of the given linguistic identity as a result of foreign language teaching.
-
Date submitted1958-03-05
-
Date accepted1958-05-01
-
Date published1958-05-09
ПЕТРОГРАФИЧЕСКАЯ ХАРАКТЕРИСТИКА ТРЕТИЧНЫХ БУРЫХ УГЛЕЙ БАБАЕВСКОГО И ДРУГИХ МЕСТОРОЖДЕНИЙ ЮГО-ЗАПАДНОГО ПРИУРАЛЬЯ
- Authors:
- Unknown
Малометаморфизованные бурые угли третичного возраста, широко распространенные в пределах правобережной Украины, юго-западного Приуралья и северного Казахстана с петрографической стороны исследованы недостаточно. До сих пор нет хорошо разработанной методики изучения малометаморфизованных рыхлых бурых углей, резко отличающихся от более плотных бурых и каменных углей, а также от торфов. В настоящей статье излагаются результаты комплексного (ботанического, петрографического и химического) изучения вещественного состава малометаморфизованных бурых углей, слагающих мощную залежь, Бабаевского месторождения и приводится сравнение их с углями других третичных месторождений юго-западного Приуралья. Вопросы происхождения малометаморфизованных бурых углей рассматриваются автором в специальной статье, подробная характеристика типов углей и строения угольных залежей отдельных месторождений Южно-уральского буроугольного бассейна излагается в подготавливаемом в настоящее время атласе.
-
Date submitted1954-07-23
-
Date accepted1954-09-17
-
Date published1955-11-17
Геологическая структура Арктики
- Authors:
- Unknown
До последних лет общее геологическое строение Арктики оставалось неясным, так как вся ее центральная часть занята водами полярных морей, в связи с чем взаимоотношения структур окружающих материков оказывались совершенно неопределенными. В течение ряда лет (1945—1952 гг.) автор, по поручению Арктического института ГУСМП, вел тематическую работу с целью расшифровки геологической структуры Центральной Арктики. Для решения этой проблемы была выполнена сводка новых материалов по структурам северной части окружающих материков и островов, а также интерпретация геофизических и батиметрических данных по центральной части Арктики (гравиметрия, магнитометрия, сейсмометрия). В результате обзора фактического материала по геологическому строению побережий и островов Полярного бассейна можно наметить расположение геологических структур Арктики, а также предположить их продолжение на север. При этом важным дополнением к геологическим данным являются новые материалы по геофизике, дающие возможность проследить продолжение главнейших структур на пространствах, закрытых водами полярного бассейна. Геофизические данные лежат в основе решения структурных вопросов для трех районов: 1) к северу от Шпицбергена и Северной Земли; 2) к северу от Новосибирских островов и 3) на меридиане острова Врангеля, на 77° с. ш.