Submit an Article
Become a reviewer
S. L. Ivanov
S. L. Ivanov
G.V. Plekhanov Saint Petersburg State Mining Institute
G.V. Plekhanov Saint Petersburg State Mining Institute

Articles

Electromechanics and mechanical engineering
  • Date submitted
    2021-03-04
  • Date accepted
    2021-04-05
  • Date published
    2021-06-24

Justification and selection of design parameters of the eccentric gear mechanism of the piston lubrication and filling unit for the mining machines maintenance

Article preview

Piston pumps are widely used in the lubrication systems of mining machines. When carrying out technical maintenance (MOT), including lubrication and filling works, at the site of operation of mining machines due to the remoteness from repair shops and warehouses of fuels and lubricants (FAL), mobile repair shops ( MRS), maintenance units (MU) and mechanized filling units (MFU) are used. The specificity of carrying out maintenance is to create conditions for the supply of oils, working fluids and lubricants to the corresponding systems of mining machines for their refueling. Existing piston pumps and pumping units, as a rule, are single-flow, and the piston is driven by a crank mechanism driven from the engine through a worm gear. The emergence of unique, hydraulic, low-mobility mining machines in open pit mining required a significant increase in the power of the MU and MFU oil pumping units, primarily for greases. However, the traditional design of the drive design of a crank-type piston pump unit at a power of over 80 kW does not allow achieving the specified operating time, it is accompanied by intensive wear of the drive elements and increased dynamics during operation. In addition, it is necessary to apply various designs of pumping units for the supply of liquid and grease lubricants. Thus, it is necessary to develop new circuit solutions for pumping units of the crank type, to improve mobile refueling facilities with a modernized design of the pump unit drive of the mobile lubrication and filling station MRS.

How to cite: Ivanov S.L., Safronchuk K.A., Olt Y. Justification and selection of design parameters of the eccentric gear mechanism of the piston lubrication and filling unit for the mining machines maintenance // Journal of Mining Institute. 2021. Vol. 248. p. 290-299. DOI: 10.31897/PMI.2021.2.13
Electromechanics and mechanical engineering
  • Date submitted
    2019-07-09
  • Date accepted
    2019-09-07
  • Date published
    2020-04-26

Promising model range career excavators operating time assessment in real operating conditions

Article preview

The development prospects of the mining industry are closely related to the state and development of modern mining machinery and equipment that meet the technical and quality requirements of mining enterprises. Enterprises are focused on a quantitative assessment – the volume of mineral extraction, depending on the functioning efficiency of a promising series of mining machines, which include modern mining excavators. Downtime and unplanned shutdowns of mining excavators directly depend on the operating conditions of the mining machine, which has negative influence on the machine as a whole and its technical condition, which entails a decrease in the efficiency of using expensive mining equipment and economic losses of the mining enterprise. The rationale for external factors that affect the operating time and technical condition of mining excavators is given. For a more detailed assessment of the influence of external influences on the efficiency of operation of mining machines, the influencing factors are divided into two groups: ergatic, directly related to human participation, and factors of a natural-technogenic nature, where human participation is minimized. It was revealed that factors of a natural-technogenic nature have the greatest influence. An algorithm is proposed for a comprehensive assessment of the technical condition and forecasting of operating time both in nominal and in real operating conditions, taking into account factors of a natural and technogenic nature. It is proposed, based on the developed program for planning and evaluating the life of a mining excavator, to adjust the schedules for maintenance and repair (MOT and R) in order to minimize the number of unplanned downtime of a mining excavator and maintain it in good condition.

How to cite: IVANOV S.L., IVANOVA P.V., KUVSHINKIN S.Y. Promising model range career excavators operating time assessment in real operating conditions // Journal of Mining Institute. 2020. Vol. 242. p. 228. DOI: 10.31897/PMI.2020.2.228
Electromechanics and mechanical engineering
  • Date submitted
    2015-11-04
  • Date accepted
    2016-01-26
  • Date published
    2016-05-01

Changes in operating time of modern domestic EKG exсavators in dependence of their functioning conditions

Article preview

Domestically produced opencast excavators are shown to be serious competition for foreign hydraulic machinery. It is suggested to estimate the potential of an opencast excavator via its basic operation effectiveness factor equal to the ratio of the scoop payload to the nominal cost of excavator operations under its normal operational conditions. Comparing the theoretical values of standard operations of hydraulic excavators of the third type-and-size group during coal mining with domestically produced EKG-18R on their operation effectiveness factor shows that the excavator exceeds foreign hydraulic models from that group 2.7-3.3 times. Theoretical foundation is provided for a complex of factors that affect the operating time of single scoop open- cast excavators, a structure is offered for the model of comprehensive assessment of operating time for opencast excavators. Complex indicators are substantiated and proposed for supporting operational effectiveness of such excavators. Assessment is offered of operational effectiveness of EKG-18R excavators following the criterion of energy consumption per excavation of a unit of rock mass. Generalization analysis is given of a set of factors that affect the value of operating time for EKG-18R excavators. Proposals are put forward on upgrading the regulations for technical maintenance and repairs of EKG-18R excavators. The task of assessing the technical state of machinery calls for using integral criteria that would enable one to identify the current technical state and the residual resource of machine aggregates, their failure potentially resulting in emergency situations accompanied by considerable property damage. It is feasible to use an integrated indicator of the degree of degradation of s machinery item for such an integrated indicator, retrieved in the course of assessing the current technical state of that item during diagnostic procedures. In its turn, such and integral indicator of the state of an item is defined by the averaged value of diagnostic indicators reduced to their basic values with the account of  their individual weight factors.

How to cite: Ivanov S.L. Changes in operating time of modern domestic EKG exсavators in dependence of their functioning conditions // Journal of Mining Institute. 2016. Vol. 221. p. 692. DOI: 10.18454/PMI.2016.5.692
Manufacturing machinery and equipment
  • Date submitted
    2013-09-26
  • Date accepted
    2013-11-27
  • Date published
    2014-03-01

Improving the strategy of electric rope shovels technical service by entering into the technical service system elements of Total Productivity Maintenance

Article preview

To date, there is need to review the existing rigid system of preventive maintenance and the transition to a more progressive system, which provides maintenance and repairs on its actual state, in which the need for repair work is based on a preliminary examination and the results of the diagnosis and monitoring of major nodes excavator. Pays special attention to the concept of TPM (Total Productivity Maintenance) for the maintenance of mining excavators.

How to cite: Shibanov D.A., Ivanov S.L., Fokin A.S., Zvonarev I.E. Improving the strategy of electric rope shovels technical service by entering into the technical service system elements of Total Productivity Maintenance // Journal of Mining Institute. 2014. Vol. 209. p. 109.
Manufacturing machinery and equipment
  • Date submitted
    2013-09-24
  • Date accepted
    2013-11-16
  • Date published
    2014-03-01

Residual life assessment gears coarse-grained open transfer of mining machines based on the local changes of their surface hardness

Article preview

The effect of local changes in the surface hardness of the end surfaces of teeth of coarse-grained gear transmissions mining machines. Represented by patterns of change of the surface hardness is not the type of reference to the loading. The estimation of the value of destruction of samples. Proposed to assess the remaining amount of coarse-grained gears with consideration of changes in the local surface hardness developed technique.

How to cite: Zvonarev I.E., Ivanov S.L., Fokin A.S., Shibanov D.A. Residual life assessment gears coarse-grained open transfer of mining machines based on the local changes of their surface hardness // Journal of Mining Institute. 2014. Vol. 209. p. 31.
Geology and metallogeny
  • Date submitted
    2012-07-29
  • Date accepted
    2012-09-07
  • Date published
    2013-01-01

Peat resources of the North-West federal district of the Russia and prospect of their development

Article preview

This paper provides an overview of the current analysis of peat resources distribution of Northwest Federal district. The analysis of peat industry is resulted. The power effective technology of career extraction of peat raw materials and manufacture of agglomerated peat fuel for needs of the distributed power is  offered.

How to cite: Mikhailov A.V., Ivanov S.L., Bolshunov A.V., Kremcheev E.A. Peat resources of the North-West federal district of the Russia and prospect of their development // Journal of Mining Institute. 2013. Vol. 200. p. 226.
Mining electromechanics and mining equipment
  • Date submitted
    2011-07-27
  • Date accepted
    2011-09-06
  • Date published
    2012-01-01

Probabilistic approach to the assessment of energy transmissions of mining machines

Article preview

In article the review of methods of a theoretical estimation  of  a resource of elements  of  cars is presented. Perspectivity of the thermodynamic approach is shown at the analysis of an expenditure of a resource by system elements. Presented a probabilistic approach in determining the energy source.

How to cite: Zvonarev I.E., Fokin A.S., Ivanov S.L. Probabilistic approach to the assessment of energy transmissions of mining machines // Journal of Mining Institute. 2012. Vol. 195. p. 249.
Automation of technological processes аnd manufactures in mining and processing industries
  • Date submitted
    2010-10-28
  • Date accepted
    2010-12-04
  • Date published
    2011-04-01

Monitoring of condition, forecastingand increasing of residual resource of transmission and supported bearings of tubular furnaces

Article preview

The reasons of an emergency stop of tubular furnaces is destruction of bearings in support of the furnace, bearings and cogwheels in mechanical transmission, failure the electric motor, infringement of integrity of the case of the furnace and it brickwork. In article possibilities on forecasting of a residual resource of bearings of support and transmission are considered, principles of construction of a complex from system of monitoring of a condition and automatic systems of greasing of bearings are offered.

How to cite: Ivanov S.L., Fokin A.S., Potapenko V.S., Podkhalyuzin S.P. Monitoring of condition, forecastingand increasing of residual resource of transmission and supported bearings of tubular furnaces // Journal of Mining Institute. 2011. Vol. 192. p. 111.
Mining machine, electrical engineering and electromechanics
  • Date submitted
    2010-07-08
  • Date accepted
    2010-09-01
  • Date published
    2011-01-01

Stand for evaluating the efficiency of transport of peat

Article preview

To reduce the use of manual labor in mining peat from deposits with the decrease of anthropogenic impacts on the environment has been developed the device with rational parameters allowing to produce therapeutic peat. In order to improve the performance proposed to use the screw with the optimal angles rise to transport both frozen and thawed peat.

How to cite: Stepuk E.Y., Ivanov S.L. Stand for evaluating the efficiency of transport of peat // Journal of Mining Institute. 2011. Vol. 189. p. 113-116.
Geotechnical engineering, powerengineering and automation
  • Date submitted
    2008-09-16
  • Date accepted
    2008-11-24
  • Date published
    2009-03-01

Comparative assessment of wear intensity of large-modular gears depending on lubrication conditions

Article preview

Ways to raise service life of open tooth gearings on an example of a drive of a spherical mill are considered. Results of introduction of automatic system of greasing are resulted and increase ways efficiency of its uses are offered.

How to cite: Ivanov S.L., Fokin A.S., Poddubnaya A.A. Comparative assessment of wear intensity of large-modular gears depending on lubrication conditions // Journal of Mining Institute. 2009. Vol. 182. p. 129-132.
Technological machinery and equipment of mining and oil & gas industries
  • Date submitted
    2007-11-18
  • Date accepted
    2008-01-05
  • Date published
    2008-05-01

Estimation of lubricating ability of oils of transmissions of mining machines

Article preview

Lubricating value shows loading capacity of transmission oil. Poor lubricating value of friction couples which are used at borderline lubrication ordinary have wear-out areas and these friction couples also fiercely attacked by corrosion. That’s why a decision of choosing oil type have to be substantiated. In this article rapid method of lubricating capacity tests is offered.

How to cite: Poddubnaya A.A., Fokin A.S., Ivanov S.L., Kremcheev E.A., Potapenko V.S. Estimation of lubricating ability of oils of transmissions of mining machines // Journal of Mining Institute. 2008. Vol. 178. p. 86-90.
Diagnostics and control of technical systems and their elements. New technologie
  • Date submitted
    2007-11-24
  • Date accepted
    2008-01-13
  • Date published
    2008-05-01

The area of existence of involute gear mesh with a given overlap coefficient

Article preview

It is shown, that application of the combined displacement while designing toothed gearings considerably allows to expand area of existence of gearing with a non-standard radial backlash. Influence of parameters of the tool on area of existence of gearing is submitted, the technology of realization of tangential displacement by generation of gears is described.

How to cite: Fokin A.S., Poddubnaya A.A., Ivanov S.L., Kremcheev E.A. The area of existence of involute gear mesh with a given overlap coefficient // Journal of Mining Institute. 2008. Vol. 178. p. 191-194.
Electric drive, power supply, automation and control of mining and oil and gas production
  • Date submitted
    2007-11-26
  • Date accepted
    2008-01-10
  • Date published
    2008-05-01

Pilot diagnostics of mining machines transmissions state by parameters of electric drive supply

Article preview

For diagnosing transmission of the mountain machine without installation of expensive gauges pilot diagnostics on parameters of a feed of the electric motor, based on the assumption can be used, that the majority of the indignations arising in transmission and influencing at the moment of resistance, overcome by the engine, affects change of instant power consumed by the electric motor.

How to cite: Poddubnaya A.A., Fokin A.S., Ivanov S.L., Ivanov A.S., Semenov M.A. Pilot diagnostics of mining machines transmissions state by parameters of electric drive supply // Journal of Mining Institute. 2008. Vol. 178. p. 159-161.
Mechanization and electrification of mining and oil & gas industries
  • Date submitted
    2007-11-22
  • Date accepted
    2008-01-23
  • Date published
    2008-05-01

Automatic centralized lubrication systems. Experience of application, problems and prospects of use

Article preview

Presented the practical useful of central oiling systems (COS) for equipment mining and building industry and determined the field using of these systems. Presented the experimental results of flooding different oil for COS bellow zero.

How to cite: Ivanov S.L., Dudko P.P., Dmitriev G.Y., Podkhalyuzin S.P. Automatic centralized lubrication systems. Experience of application, problems and prospects of use // Journal of Mining Institute. 2008. Vol. 178. p. 22-26.
Geotechnical engineering, powerengineering and automation
  • Date submitted
    2006-11-30
  • Date accepted
    2007-01-21
  • Date published
    2007-05-01

Experimental evaluation of transmission condition on the stand with closed power flow

Article preview

Advanced diagnostic and monitoring devices are required to carry out timely maintenance and repair of mining equipment and to reduce the number of emergency shutdowns. The article presents a comparative analysis of vibration and acoustic emission diagnostic techniques.

How to cite: Fokin A.S., Poddubnaya A.A., Ivanov S.L. Experimental evaluation of transmission condition on the stand with closed power flow // Journal of Mining Institute. 2007. Vol. 173. p. 119-121.
Without section
  • Date submitted
    2003-07-23
  • Date accepted
    2003-08-12
  • Date published
    2004-02-01

Faculty of Mining and Electrical Engineering of St. Petersburg Mining Institute

Article preview

The article describes the history of the formation and development of the Faculty of Mining and Electrical Engineering at the St. Petersburg State Mining Institute. Its current state is described. Information about leading scientists, founders of the faculty is presented.

How to cite: Ivanov S.L., Kozyaruk A.E., Kuleshov A.A., Semenov M.A. Faculty of Mining and Electrical Engineering of St. Petersburg Mining Institute // Journal of Mining Institute. 2004. Vol. 157. p. 7-12.
Mining engineering technologies. Diagnostics and control of technical systems and their elements. New technologies
  • Date submitted
    2003-07-28
  • Date accepted
    2003-08-09
  • Date published
    2004-02-01

Features of gear design with combined displacement

Article preview

Application of the combined displacement when designing gears allows to considerably expand the area of existence of meshing with non-standard radial clearance. The influence of the parameters of the rack-shaped producing contour on the region of the meshing existence is shown, the technology of the tangential displacement realization during gear cutting is described.

How to cite: Ivanov S.L., Kuznetsova N.V., Poddubnaya A.A., Fokin A.S. Features of gear design with combined displacement // Journal of Mining Institute. 2004. Vol. 157. p. 163-166.
Mining engineering technologies. Diagnostics and control of technical systems and their elements. New technologies
  • Date submitted
    2003-07-19
  • Date accepted
    2003-08-21
  • Date published
    2004-02-01

Experimental evaluation of wear resistance of spur gears

Article preview

Extensive opportunities to influence the properties of involute gears are available with combined displacement of tooth profiles - a combination of radial and tangential displacements, including the use of cutting tools with a standard initial contour. In particular, by combined displacement, the bending strength and wear resistance of cylindrical gear teeth can be increased by one and a half to two times, which is commensurate with material replacement.

How to cite: Ivanov S.L., Fokin A.S. Experimental evaluation of wear resistance of spur gears // Journal of Mining Institute. 2004. Vol. 157. p. 167-170.
Mining engineering technologies. Diagnostics and control of technical systems and their elements. New technologies
  • Date submitted
    2003-07-03
  • Date accepted
    2003-08-06
  • Date published
    2004-02-01

Energy service life of the plain bearing

Article preview

Design schemes of pneumatic, hydraulic and drilling machines with combined drive, used in mines and mines, mainly have mechanical drives of drilling rod rotation. This refers to machines of domestic and foreign production. A considerable part of failures of drilling equipment occurs exactly due to the fault of rotary units. One of the weak points of the design is often the transmission output shaft support unit made on the basis of plain bearing. The energy and life of such a sliding bearing is limited by the limit value of wear, leading to the occurrence of unacceptable misalignment of the gear wheels’ axes. The expression for determining the energy resource of the plain bearing from the condition of permissible volume wear of the liner material is proposed.

How to cite: Kremcheev E.A., Ivanov S.L. Energy service life of the plain bearing // Journal of Mining Institute. 2004. Vol. 157. p. 178-180.
Without section
  • Date submitted
    2000-07-15
  • Date accepted
    2000-08-16
  • Date published
    2001-02-01

New developments in mechanical equipment at the Faculty of Mining and Electrical Engineering

Article preview

The main results of research work performed at the departments of the mechanical cycle of the Faculty of Mining and Electromechanics in 2000 are presented. Research and design works for making effective and environmentally safe machines and complexes for mining and processing industries are made at the Faculty of Mining and Electromechanics under the guidance of leading experts. The analysis of design and operating characteristics of manufactured dump trucks is given and modern principles of formation of design and operating requirements to them are formulated. A methodology and mathematical model for determining the optimal characteristics of the complexes have been developed. Studies on the development of hydraulic transport equipment for underwater development of offshore mineral deposits have been carried out. New technological schemes of slurry hydrotransportation in flexible sectional pipelines of variable curvature united by spherical joints are proposed. Research work on the development of the theory of working processes and improvement of electromechanical mining equipment complexes for energy-saving technologies was carried out.

How to cite: Ivanov S.L., Kuleshov A.A., Makhovikov B.S., Timofeev I.P. New developments in mechanical equipment at the Faculty of Mining and Electrical Engineering // Journal of Mining Institute. 2001. Vol. 147. p. 105-111.
Mining
  • Date submitted
    1994-09-03
  • Date accepted
    1994-11-15
  • Date published
    1995-03-01

Совершенствование методов расчета и оценки качества горных машин (на примере привода подачи типа "Урал")

Article preview

Изложен разработанный первый этап комплексного энергетического метода определения потерь энергии в элек­тромеханическом приводе, испытывающем случайные динамические нагрузки. Метод основан на сочетании расче­та и эксперимента по определению потерь в диапазоне ре­альных нагрузок, преодолеваемых приводом. Метод отрабатывается на серийном гидроприводе подачи комбай­на типа УPC.

How to cite: Ivanov S.L., Kolomiitsov M.D. // Journal of Mining Institute. 1995. Vol. 142. p. 113.
Without section
  • Date submitted
    1992-09-04
  • Date accepted
    1992-11-21
  • Date published
    1993-03-01

Область существования зацепления цилиндрических зубчатых колес с заданным коэффициентом перекрытия

Article preview

Широкое распространение шестеренных гидромашин, и в частности гидронасосов, объясняется их высокой технологичностью и простотой конструкции. Од­нако наличие защемленного объема шестеренной гидромашины, обусловленного реализацией зоны двупарного зацепления при коэффициенте перекрытия ε α > I , ведет в снижению объемного КПД гидромашины, а также требует технологических и конструктивных мероприятий по разгрузке защемленного объема, что в конеч­ном счете сказывается на трудоемкости изготовления пгдромашины, снижает ре­сурс работы ...

How to cite: Ivanov S.L. // Journal of Mining Institute. 1993. Vol. 138. p. 15.
Without section
  • Date submitted
    1992-09-18
  • Date accepted
    1992-11-07
  • Date published
    1993-03-01

Совершенствование шестеренных гидромашин геометрией зацепления

Article preview

В зависимости от конструкций шестеренных гИдромашин их используют в качестве насосов, моторов и делителей потоков при давлении до 28-30 МПа в силовых гидросистемах машин. В диапазоне давлений 0,3-2,5 МПа применя­ют насосы в системах смазки двигателей, трансмиссий различных рабочих ма­шин, в компрессорах. Шестеренные насосы применяют также для перекачки и транспортировки жидкостей и квазижидких сред с температурой до 250 °С и вязкостью 1-3800 сСт, включая агрессивные и абразивные среды ...

How to cite: Ivanov S.L., Ivanov I.P., Krasnozhon O.A. // Journal of Mining Institute. 1993. Vol. 138. p. 61.
Without section
  • Date submitted
    1985-08-11
  • Date accepted
    1985-10-25
  • Date published
    1986-02-01

Распирающие усилия при внедрении клина в шпур

Article preview

Задача внедрения клина в деформируемую преграду решалась многими исследователями применительно к работе бурильных машин, струговых установок, добычных комбайнов и другой аналогичной техники, т.е. для усло­вий, когда клин на своем острие испытывает больше соп­ротивления при внед­рении в разрушаемую породу ...

How to cite: Korsakov P.F., Ivanov S.L. // Journal of Mining Institute. 1986. Vol. 108. p. 39.
Without section
  • Date submitted
    1983-07-26
  • Date accepted
    1983-09-06
  • Date published
    1984-01-01

Конструктивные схемы рабочих органов машин для невзрывного разрушений негабаритов

Article preview

Одной из актуальных, влияющих на эффективность горного производства проблем, является подготовка горной массы в погрузке. Эта проблема вклю­чает не только работы по дроблению горных пород массовым взравом, но и разрушение негабаритных кусков ...

How to cite: Korsakov P.F., Ivanov S.L. // Journal of Mining Institute. 1984. Vol. 99. p. 105.