-
Date submitted2023-09-05
-
Date accepted2024-11-07
-
Date published2025-02-25
Investigation of the accuracy of constructing digital elevation models of technogenic massifs based on satellite coordinate determinations
At all stages of the life cycle of buildings and structures, geodetic support is provided by electronic measuring instruments – a laser scanning system, unmanned aerial vehicles, and satellite equipment. In this context, a set of geospatial data is obtained that can be presented as a digital model. The relevance of this work is practical recommendations for constructing a local quasigeoid model and a digital elevation model (DEM) of a certain accuracy. A local quasigeoid model and a DEM were selected as the study objects. It is noted that a DEM is often produced for vast areas, and, therefore, it is necessary to build a local quasigeoid model for such models. The task of assessing the accuracy of constructing such models is considered; its solution will allow obtaining a better approximation to real data on preassigned sets of field materials. A general algorithm for creating both DEM and local quasigeoid models in the Golden Software Surfer is presented. The constructions were accomplished using spatial interpolation methods. When building a local quasigeoid model for an area project, the following methods were used: triangulation with linear interpolation (the least value of the root mean square error (RMSE) of interpolation was 0.003 m) and kriging (0.003 m). The least RMSE value for determining the heights by control points for an area project was obtained using the natural neighbour (0.004 m) and kriging (0.004 m) methods. To construct a local quasigeoid model for a linear project, the following methods were applied: kriging (0.006 m) and triangulation with linear interpolation (0.006 m). Construction of the digital elevation model resulted in the least aggregate value of the estimated parameters: on a flat plot of the earth’s surface – the natural neighbour method, for a mountainous plot with anthropogenic topography – the quadric kriging method, for a mountainous plot – quadric kriging.
-
Date submitted2022-03-24
-
Date accepted2022-07-21
-
Date published2022-12-29
A probabilistic study on hole cleaning optimization
- Authors:
- Seyyed Shahab Tabatabaee Moradi
Hole cleaning is considered as one of the most important drilling fluid functions. An efficient hole cleaning ensures a reliable well drilling practice with minimum troublesome problems. In this study, two main steps of hole cleaning, i.e., cuttings removal from under the bit and cuttings transport to the surface are discussed based on the drilling data of a shale formation. The traditional models for optimization of each step are presented. As the models require variety of input data, which are usually subjected to some extent of errors and uncertainties, the output of the model is also an uncertain parameter. Using Monte Carlo simulation, a simple probabilistic study was conducted to quantify the certainty level of the obtained results. Based on the result of this study, it is shown that for the proposed well, a good hole cleaning is expected. However, a more reliable decision for further hole cleaning optimization should be made considering the results of uncertainty analysis.
-
Date submitted2021-07-19
-
Date accepted2022-05-31
-
Date published2022-07-13
Study of a set of factors influencing the error of surveying mine facilities using a geodesic quadcopter
The factors influencing the qualitative and quantitative components of the result of surveying in open-pit mining using a quadcopter were identified and systematized, and the mathematical dependence of the influence of factors on the final error of surveying was determined. After a large number of field observations – numerous flights of a geodesic quadcopter over mining facilities – the subsequent mathematical justification of the results of the aerial photogrammetric surveying was made, which allowed to analyze the degree of participation in the final accuracy of the survey of each of the considered factors. The results of this study demonstrate the source of errors, which provide the surveyor with the opportunity to efficiently and competently carry out pre-flight preparation and planning of fieldwork. The study and subsequent consideration of the factors affecting the accuracy of surveying with the use of an unmanned aerial vehicle are the basis for the subsequent development and formation of a methodology for using a geodesic quadcopter in the conditions of open-pit mining.
-
Date submitted2020-05-13
-
Date accepted2021-05-21
-
Date published2021-09-20
Increasing the efficiency of technological preparation for the production of the manufacture components equipment for the mineral resource complex
An increase of components production for the equipment intended for oil and gas production is a key factor for analyzing existing technological processes and searching for new technological solutions to improve the efficiency of the production process and the quality of components. The article presents a simulation model designed to determine the rational technological processing parameters for the production of the “Centralizer shell” part. The basis for optimizing the working cycle of a production line is synchronization based on the principle of proportionality, which involves equalizing the duration of all technological operations with the rhythm of the production line. Synchronization of technological operations on the production line is carried out by choosing rational cutting parameters for each technological transition (cutting speed, feedrate, number of working passes). The “Centralizer shell” part is made of titanium alloy VT16, which has high strength, corrosion resistance and ductility. For the part under consideration, the permissible values of the cutting parameters were determined based on the calculation of the total processing error, as well as the frequency of replacement of the worn cutting tool. The simulation model described in the article made it possible to increase the efficiency of the production process due to the synchronization of technological operations and the search for rational technological parameters, as well as to improve the manufacturing quality of the “Centralizer shell” part by analyzing the processing error at various parameters of the technological process.
-
Date submitted2019-07-06
-
Date accepted2019-08-25
-
Date published2019-12-24
Improving the efficiency of technological preparation of single and small batch production based on simulation modeling
Technological preparation of production is an integral stage of the production process, which is characterized by high complexity, which is largely felt in the conditions of single and small-scale types of production. The effectiveness of technological preparation of production is increased through automation with the use of simulation modeling. The objective of the study is to develop a simulation model that allows you to determine a rational version of the process for processing a batch of parts. The simulation model described in the article allows to analyze the production schedule of the enterprise, build processing routes, evaluate options for using various types of workpieces and technological equipment, determine the acceptable values of cutting conditions, and choose a rational variant of the technological process of processing a batch of parts. The developed simulation model is based on the principles of modular technologies, the part is considered as a combination of individual elementary surfaces. Each elementary surface contains information about the technological processing route, technological equipment and the type of technological equipment used in its manufacture, cutting conditions and the size of the allowance for each processing stage. The rational choice of the technological process is selected on the basis of multicriteria analysis according to three criteria: the value of variable costs, the production time of a batch of parts and the value of the processing error. The analysis of these criteria is made and the parameters that have the greatest impact on their value are determined. The developed classification of surface elements is described: design elements, technological elements, basic elements, as well as a mathematical model based on which the calculation of the values of the criteria for choosing a rational option.
-
Date submitted1958-03-28
-
Date accepted1958-05-11
-
Date published1958-05-09
ОБ УЧЕТЕ ВЛИЯНИЯ ПЛОСКОЙ ЗЕМНОЙ ПОВЕРХНОСТИ В ЭЛЕКТРОРАЗВЕДКЕ
- Authors:
- Unknown
Обычно применяемый в электроразведке постоянным током приближенный способ учета влияния земной поверхности состоит в удвоении значений электрического потенциала, найденного для случая тела, находящегося в электрическом поле в неограниченной вмещающей среде, т.е. при отсутствии границы раздела земля — воздух. В настоящей работе приводится анализ погрешностей, вносимых указанным выше методом учета влияния плоской земной поверхности, для тел правильной геометрической формы. С этой целью для приближенных кривых потенциала, рассчитанных с использованием обычного приема удвоения, подбирается такая форма поверхности тела, для которой решение, полученное путем удвоения, оказывается абсолютно точным.