-
Date submitted2022-05-17
-
Date accepted2022-09-06
-
Date published2022-11-03
On the need to classify rock mass fed to dry magnetic separation
The hypothesis of a possible use of dry magnetic separation is substantiated on the example of ores from ferruginous quartzite deposits operated by plants of PAO “Severstal” Holding. Size class of ore after medium crushing is –80+0 mm when the vibrating feeder is used for feeding ore mass to the separation zone. The rationale is based on the analysis of video recording of physical simulation on a laboratory drum magnetic separator of SMBS-L series, in the VSDC Video Editor, and simulation modelling of dry magnetic separation on its virtual prototype in Rocky DEM software package. It has been proved that the use of a vibrating feeder for feeding the material to the working area of a magnetic separator makes it possible to: form a monolayer on the surface of the vibrating feeder chute with a thickness close to the maximum size of a lump of separated ore; implement batch feed of material to the separation zone; increase the spacing between lumps in the separation zone when passing through the free fall area, thereby allowing dry magnetic separation of ferruginous quartzites of size class –80+0 mm without pre-preparation.
-
Date submitted2022-06-20
-
Date accepted2022-10-07
-
Date published2022-11-03
Evaluation of deformation characteristics of brittle rocks beyond the limit of strength in the mode of uniaxial servohydraulic loading
One of the most reliable methods for assessing the physical and mechanical properties of rocks as a result of their destruction are laboratory tests using hard or servo-driven test presses. They allow to obtain reliable information about changes in these properties beyond the limit of compressive strength. The results of laboratory tests of rich sulfide ore samples are presented, which made it possible to obtain graphs of their extreme deformation. Both monolithic samples and samples with stress concentrators in the form of circular holes with a diameter of 3, 5 and 10 mm were tested. It was revealed that during the destruction of the samples, the modules of elasticity and deformation decrease by 1.5-2 times, and in the zone of residual strength – by 5-7 times.
-
Date submitted2020-06-15
-
Date accepted2020-06-15
-
Date published2020-06-30
Multi-terminal dc grid overall control with modular multilevel converters
This paper presents a control philosophy for multiterminal DC grids, which are embedded in the main AC grid. DC transmission lines maintain higher power flow at longer distances compared with AC lines. The voltage losses are also much lower. DC power transmission is good option for Russian north. Arctic seashore regions of Russia don't have well developed electrical infrastructure therefore power line lengths are significant there. Considering above it is possible to use DC grids for supply mining enterprises in Arctic regions (offshore drilling platforms for example). Three different control layers are presented in an hierarchical way: local, primary and secondary. This whole control strategy is verified in a scaled three-nodes DC grid. In one of these nodes, a modular multilevel converter (MMC) is implemented (five sub-modules per arm). A novel model-based optimization method to control AC and circulating currents is discussed. In the remaining nodes, three-level voltage source converters (VSC) are installed. For their local controllers, a new variant for classical PI controllers are used, which allow to adapt the values of the PI parameters with respect to the measured variables. Concerning the primary control, droop control technique has been chosen. Regarding secondary level, a new power flow technique is suggested. Unbalance conditions are also verified in order to show the robustness of the whole control strategy.
-
Date submitted2020-05-05
-
Date accepted2020-05-24
-
Date published2020-06-30
Justification of stripping and development of a modular mine site for a combined coal mining method in Kuzbass on the example Baikaimskaya mine site
- Authors:
- Roman I. Shishkov
- Valerii A. Fedorin
The article considers one actual method for development coal deposits in the Kuzbass by open-underground mining. The scientific and practical advantages of the proposed method due to the use of common infrastructure of coal mine and a modular mine site (subsequently transformed into a mining and technological structure operating according to the mine – longwall scheme) are presented. Currently, a development strategy for Kuzbass until 2035 has been developed. As part of the strategy, a draft program for subsoil use is being formed in the coal industry department. The program should take into account all the positive and negative aspects associated with coal mining in cities and municipal areas and also their prospects. In the Kuznetsk coal basin, 42 mines and 52 opencast mines are mining, of which 12 enterprises use partially unified infrastructure. According to the results of open-underground mining work conducted by the laboratory of the Institute of Coal and Coal Chemistry of the Siberian Branch of the Russian Academy of Sciences (Institute of Coal SB RAS), the list of sites includes favorable mining and geological conditions with incidence angles of up to 18 degrees. As open-pit coal production increases, many sites encounter such a parameter as maximum allowable (boundary) strip ratio. At the stage of preparing the feasibility study for the development of a coal deposit, this coefficient is calculated first of all, since duration of enterprise’s work and its economic component depend on it. In order to increase parameters, it is necessary to carry out transition from open works to underground. As a result, coal mine will not work at a loss, providing production with an economically disadvantageous strip ratio.
-
Date submitted2019-04-30
-
Date accepted2019-07-16
-
Date published2019-10-23
Salt Rock Deformation under Bulk Multiple-Stage Loading
- Authors:
- I. L. Pankov
- I. A. Morozov
The paper presents experimental justification of the possibility to use bulk multiple-stage loading to study the process of salt rock deformation in the laboratory conditions. Results of comparative tests between bulk multiple- stage and single-stage loading of salt rock samples are demonstrated. The paper contains results of research on the rate of lateral pressure and its impact on strength limit and residual strength limit of sylvinite, estimated using single- stage and multiple-stage methods. Research results demonstrate how the rate of lateral pressure impacts dilatancy boundary of salt rocks. Analysis of how the loading method influences certificate parameters of Mohr-Coulomb strength of sylvinite has been carried out. The dynamics of elastic modulus in the process of salt rock deformation is analyzed depending on the rate of lateralpressure. It is demonstrated how the method of multiple-stage loading adequately reflects the processes of salt rock de- formation and decomposition, and facilitates not only lowering impact of sample’s inner structure heterogeneities on the experimental results, but also significant reduction in the required amount of rock material.
-
Date submitted2014-12-25
-
Date accepted2015-02-07
-
Date published2015-12-25
Nondestructive control of elasticity modulus anisotropy of composite materials in the products
- Authors:
- A. I. Potapov
The technique of nondestructive control of anisotropy of composite materials in a product us-ing a pulse ultrasonic method is considered in the article. Calculated dependence to determine the degree of filler orientation in a polymeric composite material with varying filler laying is shown. The following filler laying is considered: chaotic, longitudinally cross, unidirectional. In addition, experimental results of anisotropy control of the elastic modulus in glass-reinforced plastics with different degrees of anisotropy using the pulsed ultrasonic method are given in the article.
-
Date submitted2009-08-10
-
Date accepted2009-10-21
-
Date published2010-02-01
Precipitation of alumina liquor inclusive potassium
- Authors:
- V. V. Radko
The materials of experimental research on alumina liquor precipitation kinetics in system Na 2 O – K 2 O – Al 2 O 3 – H 2 O using carbonated alumina hydroxide as a seed are presented. Particle size distribution (PSD) analyses of settling products are given. Correlation link of alumina liquor decomposition degree and average median diameter of received aluminum hydroxide are shown.
-
Date submitted2008-10-29
-
Date accepted2008-12-06
-
Date published2009-12-11
Data collection and processing system of low-frequency electrical method with artificial source
- Authors:
- A. I. Geraskin
Review of the basic components of elaborating system is presented. The basic trends of application of these components and software products created on their basis are shown. The concept of a processing graph is entered and shown its dynamic features. Specific examples of the successful practical application of the system are considered.