SELECTION OF THERMO-MECHANIC MODE OF PELLET MOLDING FROM TiO2 POWDER FOR MAGNETRON APPLICATION OF COMPOSITE COATINGS ON PARTS
- 1 — Moscow State University of Technology «Stankin»
- 2 — Moscow State University of Technology «Stankin»
Abstract
It is advisable to make film coatings based on titanium dioxide for the details of instrumentation industry to reduce their resistance from compositions with other oxides. It is desirable to prepare the compounds during coating stage by magnetron method. Comparison of the designs of magnetron installations substantiates the rationality of using an installation with a single magnetron, equipped with a pellet from a composition of powders based on titanium. The coating technology using a single magnetron equipped with a composite pellet is described using an example of the application of wear-resistant self-lubricating coatings from a Ti + WS 2 composition. To equip the magnetron with a TiO 2 powder pellet, the task was to ensure the greatest uniformity of the density distribution in the pellet volume, and to achieve the greatest value of this density. As a result of the study of the technology of hot molding of TiO 2 powder described in the article, the efficiency of combining the heating of a powder with its compaction in one operation is shown. During this operation, the dependence of the density of the produced pellet on the molding temperature, pressure, holding time under pressure and grain size was experimentally investigated. The chosen thermomechanical mode of TiO 2 pellet molding is substantiated. By using the following mode (in the studied range) of molding it is possible to produce the pellet with the highest density: temperature 1300 ° С , pressure 40 MPa, holding time under pressure 20 min, and grain size 2.2 μ m.
References
- Дамаскин Б.Б. Электрохимия / Б.Б.Дамаскин, О.А.Петрий, Г.А.Цирлина. М.: Химия, 2006. 670 с.
- Износостойкость композиционных покрытий для режущего инструмента / М.Ш.Мигранов, А.М.Мигранов, С.М.Мингалеев, С.Р.Шехтман // Вестник МГТУ «Станкин». 2017. № 4(43). С. 38-42.
- Моррисон С. Химическая физика поверхности твердого тела. М.: Мир, 1980. 488 с.
- Создание на основе переработки титановой стружки наноструктурированных износо-стойких самосмазывающихся покрытий на поверхностях деталей машин и технологического инструмента / А.М.Дмитриев, А.И.Беликов, Н.В.Коробова, Ю.В.Панфилов // Технология легких сплавов. 2010. № 3. С.79-86.
- Сотова Е.С. Технология нанесения AG-содержащего покрытия на полимерные изделия медицинского назначения для усиления их антибактериального действия / Е.С.Сотова, С.В.Федоров // Вестник МГТУ «Станкин». 2017. № 4 (43). С. 33-37.
- Технология создания наноструктурированных износостойких покрытий с использова-нием отходов титана / А.М.Дмитриев, А.И.Беликов, Н.В.Коробова, Ю.В.Панфилов // Ремонт, восстановление, модернизация. 2010. № 4. С. 30-33.
- Федоров С.В. Гидроструйная обработка как способ предварительной подготовки по-верхности твердого сплава перед нанесением износостойкого покрытия / С.В.Федоров, Д.Вайс, Х.Со.Мин // Вестник МГТУ «Станкин». 2017. № 4 (43). С. 48-51.
- Collins J.A. Failure of materials in mechanical design. New York: John Wiley & Sons, 1981. P.188-193.
- Correlanion between microstructure and mechanical properties of severely deformed metals / J.Gubicza, N.Q.Chinh, J.L.Laʹbaʹr, Z.Hegedus, S.Dobatkin, T.G.Langdon // Journal of Alloys and Compounds. 2009. Vol. 483. № 1-2. P.271-274.
- Dmitriev A.M. Expanding of Application of Cold Die Forging by Inducing Active Contact Friction Forces / A.M.Dmitriev, N.V.Korobova // Journal of Friction and Wear. 2013. Vol. 34. P.232-237.
- Huang T.-H. Effect of grain size on mechanical revolution of pure titanium and die cavity filling rate in hot squeezing mini spur-gear forming process / T.H.Huang, C.P.Jiang, F.V.Grechnikov // International Journal of Precision Engineering and Manufacturing. 2017. Vol.18. Iss. 10. P.1371-1377.
- Johnson W. Rupertʹs glass drops: Residual-stress measurements and calculations and hy-potheses for explaining disintegration fracture / W.Johnson, S.Chandrastrar // Journal of Materials Processing Technology. 1992. Vol. 31. P. 413-440.
- Macsarov V.V. Managing the Process of Chip Formation by Preliminary Local Action on the Worcable Surface of the Worcpiece / V.V.Macsarov, J.Olt // Journal of Mechanical Engineering. 2008. № 6. 45 p.
- Madissoo M. Testing of the External Tool Holder Equipped with Alternate in its Construc-tion / M.Madissoo, A.Rassner, V.Maksarov, J.Olt // Material Science. 2015. Vol. 21. № 3. P.391-395.
- Olt J. Dynamic Simylation of Chip Formation in the Process of Cutting / J.Olt, F.Liyvapuu, M.Madissoo, V.Maksarov // International Journal of Materials & Product Technology. 2016. Vol. 53. № 1. P. 1-14.