-
Date submitted2023-09-08
-
Date accepted2024-06-03
-
Date published2024-12-25
Modern approaches to barium ore benefication
Barite is one of the critically important minerals in several industries, including the fuel and energy, nuclear, and medical sectors. For decades, its extraction did not require any complex techniques; however, with the depletion of rich barite-bearing veins around the world, the circumstances have changed. While the demand for barite is growing widely, it is necessary to optimize and improve the existing methods for benefication of barite and barite-containing ores, and create new approaches to extracting this mineral, as well as develop technogenic barite deposits accumulated in large quantities during the previous ore production. Dumps and tailings often demonstrate high barite content, while new mining technologies make its extraction cost-efficient. Russian and foreign papers of the last 14 years provide data on the current state of primary and technogenic deposits, areas of barite use and the approaches employed for its benefication. Considering the expansion of the range of barite applications, the growing need for the mineral in the oil and gas industry and the difficulties in developing new barite deposits in Russia, the importance of new approaches to the enrichment of ore tailings in polymetallic deposits is revealed.
-
Date submitted2022-05-23
-
Date accepted2022-07-21
-
Date published2023-02-27
Alluvial tin mining by spray-suction borehole method: a case study on remaining alluvial tin reserves in Bangka Belitung, Indonesia
The area of the Bangka Belitung Islands, which is a potential area for alluvial tin deposits in Indonesia, has been affected by the destruction of tin reserves on the mainland due to rampant artisanal mining, which has left remnants of small-dimensional reserves. The remnants of these reserves can no longer be mined using the hydraulic mining of open pit method due to the small dimensions of the deposits. The hypothesis is that such sedimentary conditions can only be mined by the borehole method. This research aimed to design tools and perform test mining using the borehole method with a spray-suction mechanism. This research produced a novelty, namely, a method and parameters for alluvial tin deposits mining using borehole mining methods, such as the excavation capacity, excavation radius, mining recovery, and dilution factor. The benefit of this research is expected to provide an opportunity to increase the amount of onshore alluvial tin reserves to support tin production.
-
Date submitted2022-03-01
-
Date accepted2022-05-25
-
Date published2022-12-29
Study on the rheological properties of barite-free drilling mud with high density
Improved drilling and reservoir penetration efficiency is directly related to the quality of the drilling mud used. The right choice of mud type and its components will preserve formation productivity, stability of the well walls and reduce the probability of other complications. Oil and gas operators use barite, less often siderite or hematite weighting agent as a weighting component in the composition of drilling muds for the conditions of increased pressure. But the use of these additives for the penetration of the productive formation leads to the reduction of filtration characteristics of the reservoir, as it is almost impossible to remove them from the pore channels. Therefore, barite-free drilling mud of increased density based on formic acid salts with the addition of carbonate weighting agent as an acid-soluble bridging agent is proposed. The results of experimental investigations on rheological parameters of barite-free solutions are given and the obtained data are analyzed. Based on the comparison of results it is recommended to use high-density drilling mud on the basis of formic acid salts (sodium and potassium formate) and with the addition of partially hydrolyzed polyacrylamide with molecular mass of 27 million.
-
Date submitted2017-10-25
-
Date accepted2018-01-17
-
Date published2018-04-24
Innovative technology of large-size products manufacture
- Authors:
- S. N. Sanin
- N. A. Pelipenko
Advantages and prospects for the use of mobile robotic machine-tools in the manufacture of large parts in the mining, cement and nuclear industries are considered, as well as the importance of using welded structures to reduce production costs. Schemes for finishing mechanical machining of welded large-sized parts such as bodies of revolution with the use of mobile robotic machine-tools equipped with a belt-grinding tool, an enlarged description of the technological process for manufacturing a large-sized shell of a welded structure are presented. The conclusion is made that it is necessary to take into consideration the use in the industry of frameless production technology, especially for the machining of large-sized parts, and the use of small mobile robotic machine-tools is a productive approach and has a prospective character. The technological approaches proposed in the article make it possible to remove the restriction on the overall size and mass of the parts being manufactured, which are proposed to be manufactured directly at the site of future operation. The effectiveness of this technology is confirmed both by theoretical research and by practical data of the authors. It was noted that the production by the domestic machine-tool industry of mobile universal and special robotic machine-tools will allow the country's engineering industry to be brought to a new, high-quality world level.