Submit an Article
Become a reviewer
Tatyana Anatolievna Larionova
Tatyana Anatolievna Larionova
assistent
Peter the Great Saint Petersburg Polytechnic University
assistent
Peter the Great Saint Petersburg Polytechnic University
St. Petersburg
Russia

Articles

Electromechanics and mechanical engineering
  • Date submitted
    2020-05-13
  • Date accepted
    2021-05-21
  • Date published
    2021-09-20

Increasing the efficiency of technological preparation for the production of the manufacture components equipment for the mineral resource complex

Article preview

An increase of components production for the equipment intended for oil and gas production is a key factor for analyzing existing technological processes and searching for new technological solutions to improve the efficiency of the production process and the quality of components. The article presents a simulation model designed to determine the rational technological processing parameters for the production of the “Centralizer shell” part. The basis for optimizing the working cycle of a production line is synchronization based on the principle of proportionality, which involves equalizing the duration of all technological operations with the rhythm of the production line. Synchronization of technological operations on the production line is carried out by choosing rational cutting parameters for each technological transition (cutting speed, feedrate, number of working passes). The “Centralizer shell” part is made of titanium alloy VT16, which has high strength, corrosion resistance and ductility. For the part under consideration, the permissible values ​​of the cutting parameters were determined based on the calculation of the total processing error, as well as the frequency of replacement of the worn cutting tool. The simulation model described in the article made it possible to increase the efficiency of the production process due to the synchronization of technological operations and the search for rational technological parameters, as well as to improve the manufacturing quality of the “Centralizer shell” part by analyzing the processing error at various parameters of the technological process.

How to cite: Khrustaleva I.N., Lyubomudrov S.A., Larionova T.A., Brovkina Y.Y. Increasing the efficiency of technological preparation for the production of the manufacture components equipment for the mineral resource complex // Journal of Mining Institute. 2021. Vol. 249. p. 417-426. DOI: 10.31897/PMI.2021.3.11
Metallurgy and concentration
  • Date submitted
    2020-06-16
  • Date accepted
    2020-07-13
  • Date published
    2020-11-24

Study of Aluminum Influence on the Adhesion of Stainless Steel in Flame Spraying

Article preview

This paper is dedicated to a study of aluminum influence on the improvement of surface adhesion strength. The main purpose of this work is to investigate the strength of adhesion to the substrate by mixing flame spray powder with aluminum, which not only possesses high corrosion resistance and conductivity, but also provides additional strength, as it combines and reacts with other components of the powder. Research results of sandblasting dependence on surface roughness parameter Ra are demonstrated. The paper describes authors’ original device for a measuring instrument “Profilometer”, which was also used for measuring roughness parameter in order to obtain comparative results. Authors present results of adhesion measurements given obtained values of surface roughness by mixing nominal chemical composition of PR-30X13 powder, used as a testing material, with aluminum, which reacts with oxides on the surface of steel substrates, imparts strength to the bonding between the coating and the substrate, protects the base metal due to a combination of chemical components of the powder and creates a layer of dense surface coating. These dependencies are analyzed and parameters, exerting the greatest influence on their values, are identified. Taking into account the results obtained through numerical modeling, authors propose a mathematical model of a dependency between adhesion strength and certain values of surface roughness for different chemical compositions of flame spray powder. These studies will help in the development of certain material types for spraying and hardening of steel parts and products in order to improve their durability.

How to cite: Stepanov S.N., Larionova T.A., Stepanov S.S. Study of Aluminum Influence on the Adhesion of Stainless Steel in Flame Spraying // Journal of Mining Institute. 2020. Vol. 245. p. 591-598. DOI: 10.31897/PMI.2020.5.11