Submit an Article
Become a reviewer
Vol 196
Pages:
226
Download volume:

Concerning the possibility of an effective hadfield's steel cold-work hardening in the working conditions of the lining of spherical mills

Authors:
V. S. Bochkov1
V. I. Bolobov2
A. P. Batalov3
Yu. P. Boitsov4
About authors
  • 1 — Saint Petersburg State Mining University
  • 2 — Saint Petersburg State Mining University
  • 3 — Saint Petersburg State Mining University
  • 4 — Saint Petersburg State Mining University
Date submitted:
2011-08-29
Date accepted:
2011-10-02
Date published:
2012-02-01

Abstract

Taking a grinding of coal ball mill (type: BTM 400/800) operating without rocks as an example it is shown that a bombardment of the armour by grinding bodies made of steel 110G13L directly is capable to raise its hardness from 200 to 320HB at the depth of the cold-hardened  layer up to 6,7 mm that will approximately 2 times increase its firmness to an abrasion. The time needed for the realization of an effective bombardment is 11 minutes, the period between strengthening cold – work hardenings is 25  days.

Go to volume 196

References

  1. Андреев С.Е. Дробление, измельчение и грохочение полезных ископаемых / C.Е.Андреев, В.В.Зверевич, В.А.Перов. М., 1966. 396 с.
  2. Горбачевский В.В. Эксплуатация и ремонт шаровых барабанных мельниц. Киев, 1967. 40 c.
  3. Гуляев А.П. Металловедение. М., 1986. 544 с.
  4. Давыдов Н.Г. Высокомарганцевая сталь. М., 1979. 176 с.
  5. Егерман У.Ф. Инструкция по ремонту углеразмольных шаровых барабанных мельниц. М., 1963. 32 с.
  6. Крюков Д.К. Футеровки шаровых мельниц. М., 1965. 184 с.
  7. Кудрявцев И.В. Влияние кривизны соприкасающихся поверхностей на глубину пластической деформации при упрочнении деталей поверхностным наклепом / И.В.Кудрявцев, Г.Е.Петушков // Повышение прочности деталей машин поверхностным деформированием: Материалы 2-й Научно-технической конференции. Пермский политехнический институт. Пермь, 1967. С 40-52.
  8. Марганцовистая сталь: Пер. с англ. Б.А.Белоуса
  9. / Под ред. М.Е.Блантера. М., 1959. 94 с.
  10. Саверин М.М. Дробеструйный наклеп. М., 1955. 312 с.
  11. Ткачев В.Н. Методы повышения долговечности деталей машин / В.Н.Ткачев, Б.М.Фиштейн, В.Д.Власенко, В.А.Уланов. М., 1971. 272 с.
  12. Шапошников Н.А. Механические испытания металлов. М.-Л., 1954. 443 с.

Similar articles

Refinements of strategy for calculating cadastral value of ground area considering encumbrances and restrictions with the aim of taxation
2012 Yu. V. Chernetskaya
Control of the condition of the rock-mass condition using tansducers of hydrostatie pressure during mining escalator tunnel of «Admiralteiskaya» underground station
2012 Yu. A. Norvatov, K. E. Volodchenko, M. V. Sergutin
Reconstruction of primary composition of metamorphic rocks of Amurskaya suites (Amurskii superterrane Central Asian orogenic belt)
2012 A. V. Kurguzova
The developing of the system of actions for realization of transition from land shares to land plots
2012 A. S. Garbatsevich
Industrial gold mineralization in the structures of the mineralized zones on the example оf the Natalka deposit in Magadan region
2012 K. E. Chernyshev
The comparative analysis of the technical and economic results of activiti russian and foreign mining diamand enterprises
2012 K. I. Pavlova, A. A. Fedchenko, L. I. Iseeva