Submit an Article
Become a reviewer
Vol 216
Pages:
44
Download volume:

Influence of the type of hardening treatment on wear-resistant materials of mining equipment

Authors:
V. I. Bolobov1
S. A. Chupin2
About authors
  • 1 — National Mineral Resources University (Mining University)
  • 2 — National Mineral Resources University (Mining University)
Date submitted:
2014-12-11
Date accepted:
2015-02-11
Date published:
2015-06-01

Abstract

For example, steel 110G13L as the material of teeth of excavator buckets, shows that the work hardening (hardening) is an effective means to increase (up to 10 times) the wear resistance of components in contact with abrasive media, such as marble, yielding the steel in a state of hard-ening of hardness. In the case of wear on the rocks (granite, gabbro) with a hardness greater than the hardness of steel, the effect of hardening has almost no effect. It was found that high-temperature thermomechanical treatment of steel 35HGSA as the material of holders of rotary cut-ters (strain at 900 С, water quenching, tempering at 230 С) leads to a substantial increase of its hardness (23 %) and durability (38 %) compared to typical heat treatment used in the manufacture of cutting tools at the factory.

Go to volume 216

References

  1. Влияние больших деформаций в горячем состоянии на структуру и свойства низкоуглеродистой стали / Н.Г.Колбасников, О.Г.Зотов, В.В.Дураничев и др. // Металлообработка. 2009. № 4 (52). С.25-31.
  2. Давыдов Н.Г. Высокомарганцевая сталь. М.: Металлургия, 1979. 176 с.
  3. Износостойкость стали 110Г13Л в различных абразивных средах / В.И.Болобов, А.П.Баталов, В.С.Бочков, С.А.Чупин // Записки Горного института. 2014. Т.209. С.17-22.
  4. Крапивин М.Г. Горные инструменты / М.Г.Крапивин, И.Я.Раков, Н.И.Сысоев. М.: Недра, 1990. 256 c.
  5. Лахтин Ю.М. Металловедение и термическая обработка металлов. М.: Металлургия, 1976. 407 с.
  6. Львов П.Н. Износостойкость деталей строительных и дорожных машин. М.: Машгиз, 1962. 89 с.
  7. О целесообразности изготовления зубьев ковшей экскаваторов из стали 110Г13Л / В.И.Болобов, В.С.Бочков, Ю.В.Лыков, А.П.Баталов; Освоение минеральных ресурсов Севера: проблемы и решения: Труды 10-й Международной научно-практической конференции; Воркутинский горный институт – филиал Национального минерально-сырьевого университета «Горный». Воркута, 2012. С.319-322.
  8. Причина быстрого износа тангенциальных резцов / В.И.Болобов, В.С.Бочков, В.В.Бобров, М.П.Талеров // Записки Горного института. 2012. Т.195. С.238-240.
  9. Хрущов М.М. Закономерности абразивного изнашивания / Износостойкость. М.: Наука, 1975. С.5-28.
  10. Хрущов М.М. Исследования изнашивания металлов / М.М.Хрущов, М.А.Бабичев. М.: Изд-во АН СССР,
  11. 352 с.
  12. Novel Physical Simulation Technique Development for Multistage Metal Plastic Deformation Processing / A.A.Naumov, Y.A.Bezobrazov, N.G.Kolbasnikov, E.V.Chernikov // Materials Science Forum. 2013. Vol.762. P.62-69.

Similar articles

Design procedure of pressure losses for hydrotransport of the high concetration pulps
2015 V. I. Aleksandrov, Pavel Vlasak
Freiberg mining academy and russia: 250 years of business cooperation
2015 V. G. Afanasev
Modeling of rock massif geomechanical state at gas extraction from coal seams
2015 M. G. Mustafin
Nondestructive control of elasticity modulus anisotropy of composite materials in the products
2015 A. I. Potapov
Freiberg mining academy and mining cadet corps: their place and role in Humboldt´s life and activities
2015 I. G. Rebeshchenkova
Mineral resources in arctic islands of Russia
2015 A. N. Evdokimov, A. N. Smirnov, V. I. Fokin