Submit an Article
Become a reviewer
P. N. Makharatkin
P. N. Makharatkin
Saint-Petersburg Mining University
Saint-Petersburg Mining University

Articles

Geotechnical Engineering and Engineering Geology
  • Date submitted
    2021-12-15
  • Date accepted
    2022-09-12
  • Online publication date
    2023-03-16
  • Date published
    2023-08-28

Substantiation and selection of the design parameters of the hydroficated equipment complex for obtaining backfill mixtures from current enrichment tailings

Article preview

The issue of the influence of the concentration of the solid phase on the reduction of energy costs and specific energy consumption during pulp transportation is considered. The procedure for preparing slurry from the current enrichment tailings is shown. A scheme is given and the operation of a hydroficated unit for thickening and hydraulic transport of backfill mixtures is described. A diagram of the movement of solid particles in one of the units of the complex – a lamellar thickener is shown. The summary table shows the main design parameters and characteristics of the lamellar thickener. A general view of the laboratory setup used for experimental studies with slurry at various concentrations is given. An example of calculating productivity, density and specific load is presented. The dependence of the shear stress on the velocity gradient was determined for various pulp concentrations. Experimental studies of the process of thickening the production of slurry from the current enrichment tailings have been carried out. It was found that the geometric dimensions of the thickener depend on the concentration of the solid phase in the transported mixture. It is concluded that the flow rate of the slurry and the head loss are functions of the rheological characteristics of the viscoplastic slurry and can be calculated from the derived calculated dependencies.

How to cite: Alexandrov V.I., Vatlina A.M., Makharatkin P.N. Substantiation and selection of the design parameters of the hydroficated equipment complex for obtaining backfill mixtures from current enrichment tailings // Journal of Mining Institute. 2023. Vol. 262. p. 541-551. DOI: 10.31897/PMI.2022.68
Electromechanics and mechanical engineering
  • Date submitted
    2017-01-16
  • Date accepted
    2017-03-11
  • Date published
    2017-06-25

Energy efficiency of hydraulic transportation of iron ore processing tailings at Kachkanarsky MPP

Article preview

The article presents analytical calculations of specific pressure losses during hydraulic transportation of slurry tailings from iron ore beneficiation processes at the Kachkanarsky MPP during the storage of processing tailings in the tailings pond. The calculations were performed based on the results of experimental studies of dependence of specific pressure losses on roughness of inner surface of pipelines lined with polyurethane coating. In the process of experimental determination of pipeline polyurethane coatings roughness, it was established that the physical roughness of the coatings is more than four times less than the roughness of steel pipelines, which leads to a decrease in the coefficients of hydraulic resistances included in the design formula for the specific pressure losses - the Darcy-Weisbach formula. The coefficients of relative and equivalent roughnesses for pipelines with and without coating have been calculated. Comparative calculations have shown that the use of polyurethane coatings of hydrotransport pipelines contributes to a decrease in the specific energy during hydraulic transportation of processing tailings of iron ore from Kachkanarsky MPP in 1.5 times. To assess the nature and intensity of changes in the physical roughness of test pipes with polyurethane coating, experiments were performed on the roughness on a laboratory hydraulic bench. The prepared slurry of the iron ore tailings of Kachkanarsky MPP was pumped through a looped pipeline, in the linear part of which three test coated pipes were sequentially installed. Experiments showed that the roughness after running 484 hours on all the samples of the pipelines varies insignificantly. Roughness values are in the range from 0.814 to 0.862 μm. As a result of the processing of experimental data by mathematical statistics, an empirical formula is obtained for calculating the surface roughness of the polyurethane coating surface, depending on the time of operation of pipeline transporting the slurry of the iron ore processing tailings.

How to cite: Aleksandrov V.I., Timukhin S.A., Makharatkin P.N. Energy efficiency of hydraulic transportation of iron ore processing tailings at Kachkanarsky MPP // Journal of Mining Institute. 2017. Vol. 225. p. 330. DOI: 10.18454/PMI.2017.3.330